TLC List of Products and Services

【Precision Metal Needle】 The world's first to maintain the same outer diameter while achieving a wider inner diameter. It is effective in eliminating residual pressure of high-viscosity liquids in microfabrication and improving discharge speed. 【Coated Metal Needle】 *Coating is available as an option. To reduce the hassle of cleaning each needle individually and the errors in quantitative discharge caused by contamination of the needle, a special coating is applied to the needle, eliminating the phenomenon of liquid rising on the needle. In cases of low-viscosity fine coating or processes that could not be discharged with conventional general needles, the coated metal needle makes it possible.

• dispenser

Using a particle mixture significantly reduces seal wear. With a patented technology dispenser, you can reassess the time and costs associated with maintenance. It can accommodate a wide range of discharge volumes and methods.

• Weighing Control

You can specify the length, number of pieces, and pitch of the Teflon tube.

• dispenser

This device is a dedicated far-infrared thermal bending transport system for side moldings. It can accommodate up to 16 fixtures for front left and right side moldings or rear left and right side moldings. The upper and lower furnaces are equipped with three vertical columns of four far-infrared heater plates arranged left, center, and right, allowing for temperature management in each column. Additionally, temperature sensors are installed in the upper and lower furnaces as a safety measure to detect abnormal temperature rises. The system allows for optimal condition management of the products through temperature setting of the far-infrared heater plates and adjustment of transport speed. The side access doors are designed with a double-layer structure, ensuring thermal insulation and safety considerations regarding the heating sensation of the exterior.

• Conveyor

This is a low-cost spray valve with a check valve and vacuum generator. The liquid setting is based on the size (gauge) of the metal needle and the spray pressure.

• dispenser
• spray

Multiple points: Nozzle count, pitch, length, and pipe thickness can be customized according to application. The image shows 7 nozzles, P3.5, 20mm, 14g. Slit: Slit length and slit gap can be selected. The image shows 15mm, 1mm. R slit: Slit length, slit gap, and R shape can be selected. The image shows 10mm, 1mm, R7.

• dispenser

1. Liquid is discharged onto a rotating disk and applied by centrifugal force. 2. The application position is set for the start and end positions of the application using the robot's coordinate values. 3. The disk will be manufactured to match the inner diameter of the tube.

• dispenser

This valve uses chemical-resistant SUS and Teflon for the wetted parts. By using a diaphragm for the sealing part, there are no seals between the drive part and the wetted part, resulting in minimal wear even with materials that may cause filler contamination, ensuring a long lifespan. It can be widely used for low to medium viscosity fluids, and the poppet valve provides a suction back effect.

• dispenser

This valve has no wear in the plunger and the cylinder part of the measuring body due to its original drive, resulting in minimal wear even with materials such as paste and filler mixtures, ensuring a long lifespan. It can be widely used for both low and high viscosity applications.

• dispenser

Easily vacuum fill directly from commercially available material containers (1KG cans, pails, one-gallon cans, resin containers, etc.) into dispensers such as syringes, cartridges, and two-component cartridges. Filling is done by creating a vacuum inside the syringe.

• dispenser
• glue

This is a system for directly filling low to medium viscosity liquids from a material can into 2-component MIXPAC cartridges using a vacuum method. (Type A container type and Type B cartridge direct type) Optional: It is also possible to recognize the filling level of the material using a camera image recognition system.

• dispenser

The original pinch valve is a rotary clamp type, making it easy to attach and detach Teflon tubes. The small pressurized container is designed to directly hold commercially available weekly adhesive containers (20g). Control can be customized according to applications, from a standalone dispenser to upper units, robots, etc. Since the liquid is pumped under pressure, it has a clean cut and can be set for a short cycle time.

• dispenser

The main body and lid are processed with U-shaped grooves, making it easy to remove the bolts and nuts. It is available in capacities of 5L and 10L, with bottom-type and container-type options.

• Other assembly machines
• dispenser

The interior is visible, and commercially available material containers can be used directly.

• dispenser

Uniform coating is applied around the inside of the pipe for low-viscosity liquids. By using simultaneous multi-point application, the work time can be reduced from a small amount to any desired quantity. Separate work and retrieval stages are established, which also improves work efficiency.

• Other industrial robots

It can apply small amounts of all types of liquids, from low viscosity to high viscosity. Since it does not use electricity or air, it can be used anywhere. By simply changing the syringe, different liquids can be easily applied.

• Other processing machines

It is possible to perform a micro-quantitative application of 0.0001 CC. Due to its simple system configuration, it excels in maintainability. Transitioning from manual operation to automated line integration can be easily accomplished.

• dispenser

Due to the fixed ratio design, the mixing ratio does not change regardless of the amount applied. The syringe type makes it easy to handle during manual operation. It has a structure that allows the concentrated solution to be filled into the syringe when not in use. It has a simple configuration of a handgun, liquid agent tank, and controller. The syringe will be made according to the mixing ratio of the liquid agent you are using.

• dispenser

It is now possible to automate the precise application of instant adhesive, which has been difficult until now.

• dispenser

Due to its high-pressure resistant gear pump structure that can be directly connected to commercially available lubricators, it is simple, compact, and features touch panel control for easy operation.

• dispenser

Micro quantitative mixing discharge Gear pump method Stirring type disposable static mixer

• dispenser

Since a valve is incorporated inside the needle's base, there is no change in the external dimensions. The vacuum mechanism of the dispenser controller is not used. When the material is loaded into the syringe, there is no leakage from the tip of the needle, which improves workability.

• dispenser

The tip of the PP-made syringe connection adapter can be locked with a two-thread screw. The valve side is NTP 1/8.

• dispenser

This is a product that has reduced costs compared to the conventional lure lock adapter. 1P (contains 4 pieces).

• dispenser

By adopting a diaphragm, there are no seals on the drive parts that come into contact with the material. The orifice ranges from φ0.2 to φ4.

• dispenser

The connection is for each PT 1/4 and 1/8. The material used is SUS316. The syringe connection adapter (luer lock) has a two-thread screw.

• dispenser

There is a tube crushing adjustment screw and cylinder stroke adjustment, allowing for the setting of discharge volume. Tube replacement is done with a rotating clamp type.

• dispenser

With the vacuum generator, materials with medium to high viscosity can be easily filled into syringes, cartridges, and two-component cartridges from 1, 10, and 18-liter cans.

• dispenser

◆ Reduced the allowable error from ±20% to ±3% to ensure more precise quantification. ◆ Shortened the response time by 50% with the discharge signal, reducing the waiting time during discharge start and stop (achieving high-speed response). ◆ Achieved even more precise discharge time control with 1/1000 second unit control. ◆ Compact size. ◆ Equipped with a high-end silencer, reducing noise by 50%.

• dispenser

◆ This product features precise control of minimal discharge volume and high-speed operation, automatic discharge via an interval timer, and an automatic stop function, enhancing convenience through the use of a timer. ◆ It is optimal for high-pressure liquid control with a double-acting control type. ◆ The external output function is diversified, making automation and interface easy. ◆ In manual mode, the digital timer is displayed on the LED, making it easy to set the automatic discharge time. ◆ Existing data is retained even after re-inputting the power supply, eliminating the need for reconfiguration.

• dispenser