レックス List of Products and Services

Equipped with 21 alarm lamps, it enhances visibility during alarms. With a protection rating equivalent to IP67, it is reliable even in harsh environments, making it an ideal gas monitor for work sites. Its intrinsically safe explosion-proof structure allows for detection even in specially hazardous areas under hydrogen and acetylene atmospheres. *Please select one gas type from Type-A1/A2/B1/B2/C1/C2/D1/D2/E/G1/G2.

• Other measurement, recording and measuring instruments

It is equipped with a K-type thermocouple sensor with a diameter of φ3.3mm and a length of 120mm. It can handle various temperature measurements with one device, such as checking the acceptance temperature of raw materials and measuring the surface temperature of products as an infrared thermometer, as well as measuring the core temperature of products as a K-type thermocouple. The emissivity can also be adjusted according to the measurement target for non-contact temperature measurements.

• Other environmental analysis equipment
• Thermometer
• Other temperature and humidity measuring instruments

CENTER350 has a resolution of 0.5℃, while CENTER352 has a resolution of 0.1℃. It measures temperature in approximately 0.5 seconds. With a wide measurement range of -20 to +500℃, it is an ideal infrared radiation thermometer for measuring temperatures in food, air conditioning equipment, electrical circuits, engines, tires, heating and cooling devices, and more.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

Calibration can be performed between -10℃ and +110℃ with a resolution of 0.1℃. Additionally, by replacing the insert, it can accommodate temperature sensors with diameters of 3.3, 4.1, 4.8, 6.4, and 9.6 mm. After connecting to the power supply and turning on the switch on the front panel, the temperature will stabilize at either 0℃ or 100℃ within approximately 10 minutes, with an accuracy of ±0.5℃ from the ambient temperature. Then, insert the thermometer's sensor into the hole of the insert that matches the size of the sensor to determine the error between the displayed temperature of the DW-3101 and the thermometer. The DW-3004 will be delivered with a calibration certificate that includes traceability.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The DW-3001 supports sensor diameters of 3.3, 4, 4.76, and 6.35 mm. After connecting to the power supply and turning the switch on the front panel to "On," the specified temperature will stabilize within ±0.5℃ after about 5 minutes. Then, insert the thermometer's sensor into a hole of the same size as the sensor to determine the error between the displayed temperature of the DW-3001 and the thermometer. The DW-3001 can be calibrated with a resolution of 0.1℃ between +33℃ and +300℃.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The BX-350 can be calibrated between +50°C and +350°C, while the BX-500 can be calibrated between +50°C and +500°C. Connect the BX-350/500 to the power supply, turn the switch on, and set it to the desired calibration temperature. After the temperature stabilizes, set the emissivity of the infrared radiation thermometer to 0.95 and measure the temperature on a large black body target. Then, determine the error between the displayed temperature of the BX-350/500 and the temperature reading of the thermometer. The BX-350/500 is equipped with an RTD (platinum resistance) temperature sensor for temperature control.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The Pt-100 sensor is used, achieving a measurement range of -199.9℃ to +199.9℃, a resolution of 0.01℃, and an accuracy of ±0.05℃. The RF-100 will be delivered with a temperature calibration certificate from UKAS (United Kingdom Accreditation Service), ensuring traceability.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The output temperature can be measured at 12 points: -20, -10, 0, +10, +30, +50, +100, +195, +250, +500, +800, and +1000℃. The MIcroCal-2 will be delivered with a traceable UKAS calibration certificate.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

This is an electronic scale powered by dry batteries (4 D batteries) that can be used anywhere without being restricted by location, and it features an auto-off function. We offer two types with capacities of 60 kg and 150 kg. *Please choose one type from below: AZ-B60K or B150.

• Weight related measuring instruments
• Scale

This is a battery-operated electronic scale that can be used anywhere, is easy to install, and can operate continuously for up to 1,000 hours. It has a capacity of 30 kg and a minimum display of 5 g.

• Weight related measuring instruments
• Scale

Regular temperature checks of thermometers are essential for reliable temperature measurement. To perform high-precision temperature calibration with the simple temperature calibrator MINI, it is recommended to use the high-precision standard thermometer RF-100 for regular temperature checks.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

You can easily check the accuracy of your infrared radiation thermometer. The temperature calibrator for infrared radiation thermometers that measure surface temperature is very expensive and not common, but ACOM has a structure that applies black enamel paint to the base steel material and attaches an aluminum tube on top of it.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The measurement range can be selected from -50 to +50℃, 0 to +100℃, 0 to +250℃, and 0 to 500℃. It is a multifunctional type with a minimum and maximum temperature alarm function, allowing for a measurement period switchable between 24 hours, 7 days, or 31 days.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The AZ-B6000 is a battery-operated electronic scale with an intrinsically safe explosion-proof design that can be used anywhere without restrictions. It has a capacity of 6 kg and a minimum display of 1 g. With a low power consumption design, it reduces CO2 emissions and features a large LCD with a backlight (equipped with an auto-off function).

• Weight related measuring instruments
• Scale

Made of stainless steel with excellent chemical resistance and corrosion resistance, available in two capacities: 320 g and 620 g. Designed for low power consumption to reduce CO2 emissions. Additionally, it features a large LCD with a backlight and an auto-off function, making it convenient for use in dark places. *Please choose either the 320 g or 620 g capacity.

• Weight related measuring instruments
• Scale

This electronic scale, powered by four AA batteries and suitable for any location, is made of stainless steel with excellent chemical resistance and corrosion resistance. *Please choose one from the following capacities: 3200g, 6200g, or 15kg.

• Weight related measuring instruments
• Scale

This is a compact explosion-proof balance with intrinsic safety Ex ia B T4 suitability, featuring a stainless steel design that is resistant to rust and chemicals, as well as dust and water-proof construction. *Please select one from the capacity options of 320 g or 620 g.

• Weight related measuring instruments
• Scale

By entering the alphabet, lot number, code number, and measurement date and time, it is possible to construct measurement record data. *Please use it together with scales from the AZ-B, CZ-B/BS, GZL-B, GZM-B, GZ/B/A/AB series.

• Weight related measuring instruments
• Scale

- It directly indicates important engineering properties such as soil compaction strength, shear strength, and cohesion in situ, making it useful for soil profile measurements. - Reliable data can also be obtained for determining the bearing capacity and stability of the subsoil.

• Testing Equipment and Devices
• others

This product complies with JIS R 5201 standards.

• Testing Equipment and Devices
• others

The hydraulic jack uses a Bourdon tube pressure gauge with a capacity of tons and a minimum scale of 100 kg.

• Testing Equipment and Devices
• others

- By connecting the parts where the penetration resistance changes from the test results, a soil layer composition cross-section can be created. - The simple dynamic cone penetration test aims to easily determine the penetration resistance of soil in situ by dropping a 5 kg hammer from a height of 50 cm.

• Testing Equipment and Devices
• others

- The rod has a diameter of φ25mm, the cone has a diameter of φ30mm, and the weight is 5kg, with a tripod equipped with wire and pulleys included. - Based on the relationship between the number of blows of the heavy cone and the penetration amount, it can measure the relative bearing capacity strength of the road subgrade and subbase, and it is applicable for similar purposes as CBR tests and plate load tests.

• Testing Equipment and Devices
• others

- A load of 100 kg is applied to a rod with a screw point, and the number of rotations (half turns) per penetration amount is determined. It is said to have a good correlation with standard penetration tests. - The test results also have a data sheet, and the condition of the soil can be clearly displayed through test tables and illustrations. There is an increasing trend of its use in soil location surveys.

• Testing Equipment and Devices
• others

- Soft ground primarily composed of weak clay, silt, or peat is optimal, and it is convenient to quickly measure the approximate cohesion and depth of cohesive soil and to grasp an outline of the ground profile. - The penetration resistance required when statically pushing a cone into the soil manually is measured with a probing ring, and estimates of the relative strength, cohesion, unconfined compressive strength, and allowable bearing capacity of cohesive soil are obtained.

• Testing Equipment and Devices
• others

The maximum particle size of the soil for this test is specified to be 53mm or less according to JIS standards. 【Features】 - The unit volume of soil at the site is replaced with dry sand, allowing for indirect measurement of the soil volume. - Applicable in cases of cohesive soil, non-cohesive soil, or gravelly soil. - Compliant with JIS A 1214 standards.

• Testing Equipment and Devices
• others

It is an easy-to-use simple scale available in several models. *Please choose one from the capacity options: 16kg, 30kg, or 60kg.

• Scale
• Weight related measuring instruments

Not only for measuring specific gravity, but when replaced with a weighing pan, it can be specified as a high-precision balance of 600g/0.01g. *Please choose either DME-220 (manual span adjustment type with external calibration weights) or DME-220H (knob-type span adjustment with built-in calibration weights).

• Scale
• Weight related measuring instruments

The GMW-12K can operate continuously for about 50 hours on two alkaline AA batteries, making it ready for immediate use on-site.

• Scale
• Weight related measuring instruments

The GM-12K can operate continuously for about 20 hours on a single alkaline rectangular battery.

• Scale
• Weight related measuring instruments

The TS-30K can operate continuously for about 150 hours on two D-size alkaline batteries.

• Scale
• Weight related measuring instruments

The temperature being measured can also be displayed digitally, and it is a multifunctional type that allows switching between measurement periods of 24 hours or 7 days, as well as setting relay contacts and minimum/maximum temperature alarms.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

The SL-4 features an energy-saving design that allows for approximately 3 years of continuous use with a single AA battery, and is used for temperature measurement and management in laboratories, schools, hospitals, food storage, animal husbandry, and residential environments.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

It can digitally display the current temperature and humidity in 0.1 units, and allows switching between measurement temperature ranges of -20 to +50°C or +5 to +40°C, as well as switching between relative humidity/dew point temperature. The measurement period can be switched between 24 hours, 7 days, or 31 days. It operates on a 100V power supply, but it also has a backup function with a 9V lithium battery in case of a power outage.

• Temperature and humidity measuring instruments
• Other environmental analysis equipment
• Thermo-hygrometer

You can measure materials such as steel, cast iron, aluminum, zinc, crystal glass, polyethylene, and polyvinyl chloride.

• Other measurement, recording and measuring instruments

It demonstrates its power in the precise thickness measurement of thin materials such as metal, plastic, ceramic, and glass, where ultrasound propagates well. - Minimum measurement unit: 0.001 mm (0.0001 inches) - Minimum measurement thickness: 0.15 mm (0.006 inches)

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

Wide measurement range, capable of measuring the hardness of all metal materials. Directly displays all hardness scales: HRB, HRC, HV, HB, HS, HL.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

Wide measurement range, capable of measuring the hardness of all metal materials, and with a built-in printer, it can print out results immediately on-site.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

A large screen (128×64 dot matrix LCD with EL backlight) displays all functions and parameters, directly showing HRB, HRC, HV, HB, HS, and HL, as well as instantly displaying three major hardness scales. Additionally, the main unit is equipped with a printer, allowing for immediate printing on-site.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

Since it is a probe separation type, it can measure objects that can only secure a narrow measurement space.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

A pocket-sized durometer can primarily measure softer rubber and plastic.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

This is a surface contour gauge with a measurement range of 0μm to 800μm and a resolution of 1μm.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

It is compatible with four standards: ISO, DIN, ANSI, and JIS. When measuring surface roughness, the sensor is placed on the surface and then uniformly slides along the surface due to the driving mechanism inside the testing device.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

It comes with a standard 5Mφ8mm probe, a low battery indicator, and an auto power-off function.

• Ultrasonic Oscillator
• Other measurement, recording and measuring instruments
• Other inspection equipment and devices

You can measure the thickness of metals, plastics, ceramics, composite materials, epoxy, glass, and other materials that transmit ultrasonic waves well.

• Other measurement, recording and measuring instruments