アルク List of Products and Services

The "Meister II CC-420" is a cutting meister compatible with carbon and steel shafts. It comes standard with a diamond blade, allowing for precise cutting with impact. The shaft can be positioned vertically, making sanding of the chip diameter easy. Additionally, it features a quiet condenser motor and can be used with a 100V power supply. 【Features】 ■ Cuts 99% of harmful carbon dust ■ Can be dust collected with a household vacuum cleaner and used with a 100V power supply ■ Achieves precise positioning ■ Sanding of chip diameter is also possible ■ Beveling of cut surfaces is also possible *For more details, please refer to the PDF document or feel free to contact us.

• cutter
• Other cutting tools

The "GS-450" is a gear specification gauge that can simultaneously measure real loft and face angle. It employs a large gauge for accurate measurement, allowing loft to be measured from 0 degrees to 60 degrees in 0.5-degree increments, compatible with drivers, putters, fairway woods, and irons. Additionally, face progression can be measured from -10 mm to +20 mm. 【Features】 ■ Simultaneous measurement of real loft and face angle ■ Loft measurement from 0 degrees to 60 degrees in 0.5-degree increments ■ Compatible with drivers, putters, fairway woods, and irons ■ Precise measurement enabled by clamping at the shaft center ■ Linear guide adopted for smooth measurement ■ Special resin used at the shaft clamp area to minimize scratches *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments
• Other measurement, recording and measuring instruments

The "GCT-400" is a grip cutter that offers exceptional sharpness and can easily cut with minimal effort. It can be used on a table, takes up little storage space, keeps the area tidy, and does not get in the way. Additionally, it features a safety design that retracts the blade tip and has a special polishing that makes it resistant to scratches on the shaft. 【Features】 ■ Safe and resistant to scratches on the shaft ■ Exceptional sharpness and easy cutting with minimal effort ■ Does not take up space on the table ■ Safety design that retracts the blade tip ■ Scratch-resistant design for the shaft *For more details, please refer to the PDF document or feel free to contact us.

• cutter
• Other cutting tools

The "SA-350" calculates the rigidity applied to the chip, bat, and center using a formula to determine the relationship between the tuning coefficient and the kick point. Mark the positions at 100 mm and 250 mm from the end and align them with the marks on the left block. Then, use the round handle at the top to lower the center bearing until it contacts the shaft, and it’s a simple operation of just pressing the lever. Additionally, we also offer the "SA-350S" with center flex. 【Features】 ■ 3-point rigidity measurement device ■ Calculates the rigidity applied to the chip, bat, and center to determine the relationship between the tuning coefficient and the kick point ■ Size: W350×D200×H340mm ■ Weight: 14.6kg ■ Accessories: Wrench *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments
• Other measurement, recording and measuring instruments

The "CC-320" is a cutting master that can cut 99% of harmful carbon dust from the body. It can cut accurately with a hit, and it cuts safely with excellent sharpness. Cutting at difficult angles is easy, and it comes with a clear protractor for fine adjustments. Additionally, sanding of chip diameters can be easily done with the shaft positioned vertically. We also offer the "ACJ300," a shaft cutting machine with a memory feature for improved workability. 【Features of the Cutting Master "CC-320"】 ■ Achieves precise positioning ■ Easy angle cutting ■ Sanding of chip diameters is also possible ■ Dust collection with a household vacuum cleaner ■ Usable with a 100V power supply ■ Quiet capacitor motor adopted *For more details, please refer to the PDF document or feel free to contact us.

• cutter
• Other cutting tools

The "ESN-300" is a shaft extractor that can achieve a 90mm stroke in a single operation. By adopting a clutch mechanism, it moves smoothly and can reliably extract shafts compared to traditional ratchet methods. Additionally, by shaping the hard rubber into a circular form, it clamps around the shaft, making it less likely to slip. We also offer socket millers "MDW-10/MDW-20/MDI-10" that do not require files or sandpaper. 【Features】 ■ Uses special rubber that does not scratch the shaft ■ Ensures reliable extraction with light handle operation ■ Complete prevention of seizing by using "square screws" for the parent screw ■ Experience time savings with a 90mm stroke in a single clamp ■ Reliable clamping with circular hard rubber *For more details, please refer to the PDF document or feel free to contact us.

• Processing Jig
• Other work tools

The "CFG-910" is a center flex gauge that can measure the load applied to the shaft. By measuring not only the center but also any arbitrary position, it allows for a comparison of the hardness at the tip and butt side, enabling more advanced club settings. Additionally, spine measurement is also a simple process that just requires setting it up. 【Features】 ■ Digital display ■ Stable measurement ■ Simple spine measurement with just setup ■ Can compare with the head and grip attached ■ Allows for easy visual confirmation of distortion by rotating the shaft *For more details, please refer to the PDF materials or feel free to contact us.

• Other electronic measuring instruments
• Other measurement, recording and measuring instruments

This document is the instruction manual for the Center Multi Gauge "CMG-500." The "CMG-500" allows you to move the center section while supporting both ends, enabling you to find the kick point and accurately locate the spine at the kick point by rotating the shaft. Please read this instruction manual carefully before use and ensure that you use it correctly and safely. 【Contents】 ■ Confirmation before preparation ■ Preparation before work ■ Features of the Center Multi Gauge ■ Basic operation section ■ Optional operation section ■ Cautions *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments
• Other measurement, recording and measuring instruments

The "FC-200" is a flex checker that accurately measures the different flexes of shaft manufacturers. It achieves a wide measurement range for flex from LL to XXX. With a left-right sliding support base that does not depend on the length of the shaft, it can accommodate everything from sand wedges to drivers. Additionally, we also offer the torque checker "TC-200," which can accurately measure torque. 【Features】 ■ Space-saving wall-mounted design ■ Easy measurement even with the head attached ■ Simple setup for spine measurement ■ Clear digital display ■ Sliding support base *For more details, please refer to the PDF document or feel free to contact us.

• Other electronic measuring instruments
• Other measurement, recording and measuring instruments

We would like to introduce the "Professional Tools" handled by Alku. Starting with the drill press jig "BJ-100," which assists in neck processing, we also offer the grip cleaner "GC-380," designed to remove tape residue from inside the grip. Our company is a top brand specializing in precision molds and precision jigs, known for our technology and ideas. Please feel free to contact us when you need assistance. 【Product Lineup】 ■ Drill Press Jig "BJ-100" ■ Loft Lie Adjustment Lever "LLB-30/LLB-22" ■ Grip Cleaner "GC-380" ■ Socket Insertion Base "DW-100" *For more details, please refer to the PDF materials or feel free to contact us.

• Processing Jig
• Other work tools

The LL-380 is a loft and lie adjuster with a plunger that can be used for both left and right-handed clubs. It achieves a wide adjustment range of loft angles from 15 to 65 degrees and lie angles from 52 to 67 degrees. Additionally, it allows for more precise adjustments with an easy-to-read scale in 0.5-degree increments. 【Features】 ■ Strong fixation with minimal force ■ Includes a rotating base; suitable for both left and right-handed use ■ Wide adjustment range and easy-to-read scale ■ Clamps with a special resin head ■ Easily visible score lines *For more details, please download the PDF or feel free to contact us.

• Other machine elements