ハルツォク・ジャパン List of Products and Services

For rough grinding and surface finishing of steel, non-ferrous metals, substrates, resins, etc. It can be used as a substitute for SiC grinding paper. White alumina features slightly higher grinding power than alumina and good friability. Its good friability makes it suitable for sample grinding as it is less likely to create large, deep scratches. 【Features】 ○ It does not fall under the Labor Safety and Health Act, so there is no hassle of maintaining 30 years of work records. ○ Higher grinding power than alumina, compatible with a wide range of samples. ○ Good friability, making it suitable for sample grinding as it is less likely to create deep scratches. ○ A wide range of abrasive grain sizes from #80 to #3000. ○ The diameter sizes are as follows: ・φ200mm ・φ203mm ・φ223mm ・φ250mm ・φ300mm ・φ305mm ○ Available in various types, both adhesive and non-adhesive.

• Hand polishing and filing

Epoxy resin is said to be the most suitable cold-cure resin for sample polishing due to its high hardness and low shrinkage rate among cold-cure resins at room temperature. This product eliminates hazardous substances such as ethylene triamine and triethylene tetraamine, yet it possesses performance characteristics such as hardness, curing time, and shrinkage that are comparable to conventional epoxy hardeners. **Benefits of Being Hazardous Substance-Free** - No need to handle materials from locked storage shelves for "pharmaceutical-grade hazardous substances." - Elimination of daily management and record-keeping for usage and remaining quantities. - No need for special leakage or theft prevention measures. - Removal of management duties for toxic substance handlers. - Reduction of safety and health concerns. By being hazardous substance-free, unnecessary tasks outside of practical work are eliminated, leading to increased productivity. Of course, it also contributes to safety and health. **Drawbacks of Being Hazardous Substance-Free** Since substances commonly used have been eliminated, there may be slight differences in user experience compared to the epoxy you have used before. Therefore, if you have concerns about usage, we can send you a free sample so you can try it out and verify for yourself. ★ It is also available for purchase on Amazon. Please check the link below.

• Ceramics
• Printed Circuit Board
• aluminum

This is a polyester resin for embedding samples. It is a two-component, room-temperature curing resin. The embedding resin is suitable for embedding samples that are prone to deformation due to heat or pressure. Additionally, while polyester resin has lower hardness compared to epoxy resin, it has a faster curing time, making it recommended for those who want to polish samples immediately. Aqua does not contain styrene, which is typically found in polyester, so it is not classified as a "special management substance" under the organic solvent method. We are distributing free samples, so please feel free to contact us if you are interested. 【Features】 - Does not contain styrene - Users are not required to undergo "specific chemical substance health examinations" - Can be stored normally, eliminating the need for management tasks - Suitable for large-scale sample testing - Fast curing time, making it suitable for urgent testing - Inexpensive ★ It is now also available for purchase on Amazon. (Link below)

• Printed Circuit Board
• Ceramics
• Steel

We will send you a free sample. If you are interested, please contact us. 【Features】 〇 This is a wet precision cutting wheel for metal cutting. 〇 It is a versatile cutting wheel made with alumina-based abrasive grains. 〇 We are able to sell it at a low price due to mass production. 〇 The sizes are as follows: Outer diameter - Hole size - Thickness ・Φ230 - 25.4 - 1.0 ・Φ255 - 31.75 - 1.2 ・Φ305 - 31.75 - 1.5 * Thanks to your support, we have received very positive feedback. We plan to expand our lineup in the future, so we will also be producing sizes other than those listed above. We are currently distributing free samples. If you are interested, please feel free to contact Harlzok Japan. You can also purchase from Amazon via the link below.

• cutter
• Cutting Oil
• Grindstone

<Features> - Cutting and polishing of rock samples can be done with one machine. - The cutting and polishing motors are shared, providing excellent cost performance. - Cutting and polishing can be performed while the sample is attached to a glass plate using a vacuum chuck. - Micron-level polishing is possible. - The operation is simple enough for anyone to use.

• Other inspection equipment and devices
• Stone Processing Machinery
• Other processing machines

This is the top model of a sample polishing machine that can polish various samples such as metals, non-ferrous metals, substrates, and ceramics. <Features> ● Increased stability with a base and head integrated design ● Ample motor capacity specifications and a stable housing enable precise polishing ● Equipped with almost all necessary functions as standard ● The left-right oscillation function of the head increases polishing speed, particularly effective for surface preparation

• Circuit Board Inspection Equipment
• Special Steel
• Optical microscope

■Sample Cutting Machine We have the MICRACUT series of small cutting machines, the SERVOCUT series of medium and large cutting machines, and the manual METACUT, among others. *The new MICRACUT-200-S has been added. ■Sample Embedding Machine We have the ECOPRESS series of resin embedding machines for samples and the VACUMET, a degassing impregnation machine for embedding with room temperature resin. ■Sample Polishing Machine We offer the bestselling FORCIPOL series of sample polishing machines, the full-spec ACCURA, the fully automatic VELOX, the ELOPREP electro-polishing machine, and vibratory polishing machines, among others.

• Plastic processing machines (cutting and rolling)

■Cutting We introduce cutting stones and diamond wheels. We have original brand products such as the Meivia series. ■Embedding We introduce hot resins such as phenol, epoxy, and acrylic, as well as room temperature resins like polyester resin (styrene-free) and epoxy resin (non-hazardous). ■Polishing We offer polishing paper, diamond plates, diamond abrasives, alumina, colloidal silica, buffs, lubricants, etc., at low prices. WA polishing paper has been added to our lineup.

• Plastic processing machines (cutting and rolling)
• Other processing machines
• Steel

EcoPress allows for the easiest embedding. You can choose from three models according to your needs. We have demo units available, so if you would like a demonstration, please feel free to contact us. Online demos and on-site demos at your company are also possible. 【Features】 ◆ It automatically performs a series of processes including heating, pressurizing, cooling, and degassing. ◆ The upper fixed cover uses a bayonet system, making it easy to remove even after sample preparation without becoming stiff. ◆ The mold can be removed individually, allowing for the use of multiple mold sizes with a single unit. *For more details, please request our materials. The catalog has been updated.

• Other machine tools
• Analytical Equipment and Devices
• Steel

The resin is compressed and pressed to embed and mold the sample. You can choose from two models according to your application. 【Features】 ◆ The entire process of heating, pressurizing, cooling, and degassing during resin molding is performed automatically. ◆ The upper fixed cover uses a bayonet system, making it easy to remove even after the sample is created, and it does not become difficult to detach. ◆ Mold diameters can be selected from Φ25, 30, 40, 50 mm and 1, 1-1/4, 1-1/2, 2 inches. There is also a chamfered ram available. ◆ The mold can be removed individually, allowing the use of multiple mold sizes with a single machine. ◆ Program management is possible, enabling various embedding conditions to be retrieved with the push of a button. ◆ It is equipped with functions for "preheating" to ensure resin penetrates into fine details and "pre-pressurizing" for embedding low-hardness non-ferrous metals, among others.

• Analytical Equipment and Devices
• Steel
• Optical microscope

For polishing samples such as metals, non-ferrous metals, substrates, ceramics, and resins. 【Features】 〇 Abrasive particle sizes range from #80 to #4000. 〇 The diameter sizes are as follows: ・φ200mm ・φ223mm ・φ250mm ・φ300mm ・φ8 inches ・φ12 inches 〇 Available in various options, both adhesive and non-adhesive. ☆ You can now purchase it on Amazon as well. 　 (There is a link below.) Please compare it with what you are currently using.

• Hand polishing and filing
• Steel
• Optical microscope

This is a resin plate containing diamond abrasive. 【Features】 〇 A wide variety of sizes (μ) and types are available. 〇 Effective for polishing hard samples that cannot be polished with sandpaper. 〇 It can be easily attached and detached using magnets. 〇 The durability is approximately equivalent to 100 sheets of sandpaper. ☆ It is now available for purchase on Amazon. Φ200mm Diamond Plate https://amzn.to/2xVIxDN Φ250mm Diamond Plate https://amzn.to/3aFh86J Φ300mm Diamond Plate https://amzn.to/3axVFwl

• Other abrasives
• Hand polishing and filing
• Other consumables

<Features> ● Automatically sets optimal parameters with the auto-scan function. ● Equipped with a cooling function to suppress the temperature rise of the chemical solution. ● Manual etching can be performed with an external etching unit. ● Expansion of the electro-polishing unit is also possible. ● Accessories such as masks and cathodes tailored to the samples are available. *For more details, please contact "Request for Information."

• Steel
• Other machine tools
• stainless

VELOX achieves complete automation of the sample polishing process. It is a device that performs not only polishing tasks but also sample cleaning, drying, holder attachment, holder replacement, and storage of holders in racks. VELOX offers overwhelming reductions in labor costs. 【Components】 ● Flat polishing station ● Rough polishing and finishing polishing stations ● Sample cleaning and drying station ● Polishing disk exchange tower ● 8-channel automatic supply unit ● Automatic holder exchange system ● Barcode scanner 【Benefits】 ● Slim design of the smallest class (about half the size of conventional machines) ● Amazingly low price (achieved by significantly cutting material costs through slimming) ● Overwhelming time savings 【Reasons to Recommend VELOX-102】 Did you know that data shows that more time is spent on tasks other than actual polishing during sample polishing? <Tasks other than polishing> ● Cleaning and drying of samples and holders. ● Removal, replacement, and storage of disks. ● Management of buffs, polishing materials, and lubricants. ● Waiting time for operators to start the next process. All of these tasks are handled by VELOX.

• Special Steel

Rock Cutting Machine <Features> - Capable of cutting large rock samples - Horizontal table movement allows for slice cutting - Can accommodate wheels up to Φ300mm - Easy operation that anyone can use

• Other inspection equipment and devices
• Stone Processing Machinery
• Other processing machines

Four-Column TS <Features> ● Designed for stability even at low speeds. ● High-precision polishing is possible with a stable housing. Four-Mat TS <Features> ● Automatic polishing is possible. ● Easy polishing with a holder dedicated to thin slices. ● Available in low-speed and ultra-low-speed specifications. ● Can be retrofitted.

• Other inspection equipment and devices
• Stone Processing Machinery
• Other processing machines

【Features】 〇 This is a wet precision cutting wheel designed for cutting aluminum samples. It is also proficient in cutting non-ferrous metals such as copper and titanium. 〇 The GC abrasive grains cut non-ferrous metal samples cleanly. 〇 It is now available for purchase on Amazon. (Link below) 〇 The sizes are as follows: Outer diameter - Hole diameter - Thickness ・Φ205 - 25.4 - 0.8 ・Φ255 - 31.75 - 1.2 ・Φ305 - 31.75 - 1.2 Free samples are currently being distributed. If you are interested, please feel free to contact Haruzoku Japan.

• cutter
• Cutting Oil
• Grindstone

【Features】 〇 This is a wet precision cutting wheel designed for cutting stainless steel samples. 〇 It cuts stainless steel samples cleanly with special abrasive grains. 〇 It is now available for purchase on Amazon. (Link provided below) 〇 The sizes are as follows: Outer diameter - Hole diameter - Thickness ・Φ205 - 25.4 - 0.8 ・Φ255 - 31.75 - 1.2 ・Φ305 - 31.75 - 1.2 We are currently distributing free samples. If you are interested, please feel free to contact Harlzok Japan.

• cutter
• Grindstone
• stainless

This is a polishing material suitable for sample polishing in cross-sectional observation, tissue observation, and defect analysis. It is a polishing agent with high-quality diamond abrasives evenly blended. 【Features】 〇 A wide range of sizes (μ) is available. 〇 There are three types of abrasive particle shapes: polycrystalline, single crystal, and natural. 〇 It is a cost-effective polishing agent that is less prone to abrasive flow. ☆ It is now available for purchase on the Amazon site. (A link is provided below.)

• Other abrasives
• Hand polishing and filing
• Other consumables

This is an abrasive suitable for sample polishing in cross-sectional observation, tissue observation, and defect analysis. It is a polishing agent with uniformly blended diamond abrasives. 【Features】 〇 A wide range of sizes (μ) is available. 〇 There are two types of abrasive shapes: polycrystalline and single crystal. 〇 Automatic supply is possible. 〇 It offers excellent cost performance. ☆ It is now available for purchase on the Amazon site. (There is a link below.)

• Other abrasives
• Hand polishing and filing
• Other consumables

This is an abrasive suitable for sample polishing in cross-sectional observation, tissue observation, and defect analysis. It is a diamond slurry abrasive with a lubricant, eliminating the need for additional lubricants, making it easy to manage polishing conditions. 【Features】 〇 A wide range of sizes (μ) is available. 〇 There are two types of abrasive grain shapes: polycrystalline and single crystal. 〇 Automatic supply is possible. ☆ It is now available for purchase on the Amazon site. (A link is provided below.)

• Other abrasives
• Hand polishing and filing
• Other consumables

This is an abrasive suitable for sample polishing in cross-sectional observation, tissue observation, and defect analysis. We uniformly blend high-quality diamond abrasives. Our company positions the suspension as a higher quality abrasive compared to slurry. 【Features】 〇 High uniformity, making it less likely to stick inside hoses, suitable for use with automatic feeders. 〇 A wide range of sizes (μ) is available. 〇 There are two types of abrasive grain shapes: polycrystalline and single crystal. 〇 If you are having trouble with finishing polishing, please try this product. ☆ It is now available for purchase on Amazon. (A link is provided below.)

• Other abrasives
• Hand polishing and filing
• Other consumables

This is an abrasive suitable for sample polishing in cross-sectional observation, microstructural observation, and defect analysis. In the polishing of steel samples, alumina abrasives often yield better results than diamond abrasives. 【Features】 〇 It is the optimal abrasive for finishing polishing of carbon-rich iron-based materials. 〇 A wide range of sizes (μ) is available. 〇 It is more affordable compared to diamond abrasives. ☆ It is now available for purchase on Amazon. (There is a link below.)

• Other abrasives
• Hand polishing and filing
• Steel

This is an abrasive suitable for sample polishing for cross-sectional observation, tissue observation, and defect analysis. It is suitable for finishing metal polishing such as aluminum and stainless steel. 【Features】 〇 Effective for finishing polishing of aluminum, stainless steel, and other materials. 〇 It has a chemical polishing effect, resulting in a smooth polished surface. 〇 Please try it on samples that cannot be polished well with diamond abrasives. 〇 Short polishing time. ☆ It is now available for purchase on the Amazon site. (There is a link below.)

• Other abrasives
• Hand polishing and filing
• aluminum

This is an abrasive suitable for sample polishing for cross-sectional observation, tissue observation, and defect analysis. It is suitable for finishing the polishing of metals such as copper and titanium. 【Features】 〇 Effective for finishing polishing of metals like copper and titanium. 〇 Please try it on samples that cannot be polished well with diamond abrasives. ☆ It is now available for purchase on Amazon. (There is a link below.)

• Other abrasives
• Hand polishing and filing
• alloy

This is a polishing material suitable for cross-sectional observation, tissue observation, and defect analysis sample polishing. It is used in conjunction with diamond abrasives during buff polishing. 【Features】 〇 Available in three types: alcohol-based, glycerin-based, and water-based. 〇 Reduces heat generation during buff polishing. 〇 Provides a sliding effect to prevent diamond abrasives from embedding too deeply. ☆ It is now available for purchase on Amazon. (There is a link below.)

• Other abrasives
• Hand polishing and filing
• Lubricants

It is a thermosetting embedding resin. 【Features】 ◆ It is said to be the most suitable resin for sample embedding among thermoplastic resins. ◆ Available in powder and granule types. ◆ High adhesion. ◆ High hardness. ★ It can also be purchased on Amazon. Please check the link below.

• Repair Agent
• Other consumables
• Optical microscope

It is a thermosetting embedding resin. 【Features】 ◆ It is the most affordable embedding resin among thermosetting resins. ◆ Available in both powder and granule types. ◆ The granule type is available in three colors for identification purposes. ★ It can also be purchased on Amazon. Please check the link below.

• Other consumables
• Steel
• Other abrasives

It is a thermosetting embedding resin. 【Features】 ◆ Contains glass fibers to reduce edge sagging. ◆ Suitable for samples made of hard metal materials. ◆ It is green in color, making it easy to check the samples. ★ It is also available for purchase on Amazon. Please check the link below.

• Repair Agent
• Other consumables
• Optical microscope

It is a thermoplastic embedding resin. 【Features】 ◆ It is a high-hardness acrylic resin. ◆ It has high transparency, allowing for the entire sample to be observed. ◆ Alcohol-based lubricants can be used. ★ It is also available for purchase on Amazon. Please check the link below.

• Repair Agent
• Other consumables
• Optical microscope

<Features> ■ The polishing machine can be used in locations without water supply and drainage facilities. ■ It is an environmentally friendly device as it does not produce polishing wastewater. ■ Control is only through valve opening and closing, so there is no need for electrical connection to the polishing machine. ■ It is compact and small enough to fit under a workbench.

• Hand polishing and filing
• tank
• Grindstone

When setting samples such as substrates or thin plates and filling them with resin, it is common for them to fall or tilt, resulting in embedding failures. Extracting the embedded samples requires additional work such as breaking or dissolving the resin, which can be a significant burden for the operator. By using sample clips, it is possible to reduce embedding failures and operator stress. 【Features】 ◆ Can stabilize thin samples upright ◆ Three types of clips available ◆ Usable for both hot and cold embedding Free samples are available. Please feel free to contact us if you are interested.

• Repair Agent
• Other consumables
• Optical microscope

This is a reusable silicone mold. It has the best release properties among embedded molds and is easy to use. Compared to plastic molds, the transparency on the sides is lower. 【Features】 ◆ Economical and reusable ◆ Good release properties, easy to remove ◆ Can embed large samples ★ It is now available for purchase on Amazon. ・Cylindrical shape https://amzn.to/3bBrs0v ・Rectangular shape https://amzn.to/2Kxmbvf

• Repair Agent
• Other consumables
• Optical microscope

Hardened steel has a high hardness and the cutting surface becomes compact, making it unsuitable for cutting with cutting wheels. However, there is a strong demand for cutting with grinding wheels, and to address this issue, Meibia S was born. Meibia S is designed with specifications that are believed to be the most suitable after repeatedly conducting cutting tests on hardened steel. 【Features】 〇 It is a wet precision cutting wheel for hardened steel. 〇 It can be used for hard iron-based materials with alumina-based abrasives. 〇 It has become possible to sell at a low price due to mass production. Free samples are currently being distributed. If you are interested, please feel free to contact Haruzoku Japan.

• cutter
• Cutting Oil
• Grindstone

We offer various clamps for securing samples for precision cutting machines. - One-touch clamp - Spring clamp - Vertical clamp - Chain clamp - Angle-adjustable clamp - Various small sample vices, etc. A wide variety of clamps are available. Additionally, custom clamps can also be created.

• cutter
• Grindstone
• stainless

The rotating sample fixation stand (rotation clamp) can be used with the precision cutting machine "MicraCut." <Features> ■Reduction of cutting time It can cut off at half the cutting distance of normal cutting. ■Reduction of cutting load The contact area of the cutting wheel is smaller, which reduces the load on the sample. ■Clean cutting of the outer circumference Since it cuts from the outer circumference, there are no burrs on the edges, making it suitable for cutting when you want to observe surface treatment.

• Special Steel
• Optical microscope
• Plastic processing machines (cutting and rolling)

Hartzok, the market leader in sample preparation equipment used in the analysis and quality control of the steel and cement industries, will introduce the fundamental technologies related to its operation and automation. [Content] This is a foundational edition that incorporates years of experience and knowledge regarding the sampling, transportation, and adjustment methods of samples and their automation. If you would like to know more, please feel free to contact us.

• Analytical Equipment and Devices
• X-ray fluorescence analyzer
• Spectroscopic Analysis Equipment

The goal of "Haltzok Workshop" is to respond to the demands of niche industries specialized in jigs and components for sample preparation. This includes dedicated holders for polishing machines, special clamps for cutting machines, and the creation of parts that other companies have declined. If it relates to sample preparation, you can trust "Haltzok Workshop." ■ Why choose Haltzok Workshop? At Haltzok, we have been providing total support for sample preparation by selling and maintaining cutting machines, embedding machines, and polishing machines, as well as offering various condition settings. For parts and jigs used in sample preparation, detailed explanations are unnecessary since the purpose of use is clear. We will also propose the necessary precision and material selection at Haltzok Workshop. Furthermore, we can accommodate requests even for equipment from other companies. If you are told that parts cannot be supplied by another company, please consult with Haltzok Workshop.

• Other machine elements
• Processing Jig
• bracket

We introduce the method for selecting specifications for sample grinding machines, often overlooked confirmation points, and how to establish new grinding conditions, from the consideration stage before purchase to the preparation methods for immediate operation after delivery, from the manufacturer's perspective. <Table of Contents> - Introduction - Let's create a specification sheet - 1. Confirm the installation location and utilities - 2. Choose between a manual or automatic grinding machine - 3. Number of grinding stages - 4. Selection of grinding disc size - 5. Confirm the direction of head movement - 6. Selection of sample pressurization method - 7. Presence or absence of an automatic feeder - 8. Confirm internal rules - After completing the specification sheet - Visualizing equipment operation - Equipment demonstration - Establishing grinding conditions - Confirming after-sales service that should not be forgotten - Conclusion When we talk to customers, it is not uncommon to hear from new personnel responsible for equipment purchases who say they have no understanding of grinding at all. We created this material in hopes of providing something useful for those who are struggling. This is not about selecting our company's equipment, but rather general content on sample grinding selection, including competitors. We hope you find it useful when selecting a sample grinding machine.

• Plastic processing machines (cutting and rolling)
• Other processing machines
• Steel

It has excellent cooling and cleaning properties, which are essential for precision cutting to avoid damaging the tissue. Furthermore, it possesses high capabilities in rust prevention and corrosion resistance, which are necessary to protect both the samples and the precision cutting machines. It eliminates the unique irritating odor of cutting oil, reducing stress for operators and improving the working environment. Additionally, the presence of metal ions is an indispensable factor to consider in precision cutting. Metal ions are a major cause of machine corrosion and paint peeling, which can shorten the lifespan of cutting machines. Abcool has properties that make it resistant to the effects of metal ions, helping to suppress coolant degradation and allowing for prolonged use. This also enables a reduction in maintenance frequency and extends equipment lifespan, promising high cost-effectiveness. 【Features】 〇 High cooling performance 〇 High cleaning power 〇 Excellent rust and corrosion resistance 〇 Ultra-low odor type 〇 High stability and long lifespan For free samples or SDS, please feel free to contact us.

• cutter
• Cutting Oil
• Grindstone

Automatic feed cutting and manual cutting by lowering the lever are possible. By setting the table, cutting of flat materials such as circuit boards and sheet metal is also possible. Furthermore, by attaching a grinding wheel, precision cutting is achievable, allowing for surface preparation and cutting to the desired area for polishing. 【Features】 - Compatible with grinding stones and wheels up to φ200mm - Compatible with polishing wheels up to φ175mm - Automatic cutting with program control - Manual cutting by lowering the lever - Parallel slicing cutting with an accuracy of 5um is also possible - Easy cutting of circuit boards with a table saw - When the cutting chamber cover is opened, the brake is applied, and the wheel stops immediately.

• Ceramics
• Printed Circuit Board
• Capacitor

This is a mini vice for the Mikura Cut series of precision cutting machines. Have you ever experienced not knowing which type of vice to choose due to the wide variety available? If you're having trouble selecting a vice, please refer to this user manual to help you choose the right vice for your sample. 〇 General-purpose vice 〇 Long-length vice 〇 Round vice 〇 Vice for irregular samples 〇 Adhesive vice 〇 Bone vice 〇 Teardrop vice 〇 Vice for vertical cutting of screws 〇 Vacuum holder for thin samples In addition, custom clamps can also be created. Please feel free to contact us.

• cutter
• Ceramics
• PCB terminal blocks

How are the storage solutions for buffs, diamond pads, and plates used in automatic polishing machines organized? Generally, drawers in workbenches are used, but there is a risk of contamination (mixing with other polishing materials), so the basic practice is to store one piece per drawer, which takes up valuable storage space. Additionally, poor drainage can lead to rust and mold issues. Therefore! We propose the "B Cube." The buff box is a space-saving vertical storage type that holds 6 pieces. It has excellent drainage and comes with a water catch pallet. 【Features】 - Can store sizes from Φ200 to 300 mm, or Φ8 to 12 inches - No issues with storing different diameter sizes - Vertical storage ensures good drainage - Comes with a water catch pallet, allowing storage of wet buffs - Wide spacing between buffs makes it easy to take in and out, even for people with larger hands - Can be stacked in two layers Please refer to the catalog for more details. For inquiries by phone, please contact us at: 03-5907-1774, Attn: Osuka Feel free to reach out with any questions!

• Storage
• cabinet
• Hand polishing and filing

If you use a disposable type for embedding, you can polish it as is with the mold. Therefore, there is no need for the process of removing it from the mold, which is expected to shorten the work time. It is suitable for cases where a large number of items are embedded, and samples can be clearly seen from the side. The size of the samples that can be embedded needs to be confirmed by the inner diameter of the ring. 【Features】 ◆ Disposable type that requires no hassle ◆ Lens effect from the acrylic ring allows for clear observation of samples from the side ◆ Suitable for large-scale embedding ★ It is now available for purchase on Amazon.

• Repair Agent
• Other consumables
• Optical microscope

◆Processing includes crushing, sample recovery, and internal cleaning of the device after sample input. ◆Equipped with a large-capacity crushing vessel of 500cc. ◆Up to 16 different operating parameters can be registered.

• Fine grinding machine