エスアールシー List of Products and Services

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) +5V, +3.3V, +12V, GND ◆Check Terminals: PRST, DEG, FAL, +5V, GND ◆Others: M66EN can be supported by pattern cutting <Features> ◆Complies with PICMG2.0R2.1 standards. ◆The characteristic impedance of the signal lines is set to 65Ω ±10%. ◆System slots are available on both the left and right sides. ◆In the 8-slot type, a long-type connector is implemented in the slot farthest from the system slot, allowing for the installation of the off-board terminator STB-64C (optional). (Please inquire) ◆If used in conjunction with the bus module bridge, please contact our sales department.

• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw terminal, ATX power connector ◆Check Terminals: PRST, DEG, FAL ◆Others: M66EN Switching <Features> ◆Compliant with PICMG2.0R3.0, PICMG2.1R1.0 (Hot Swap), and PICMG2.10R1.0 (Keying) standards. ◆Signal line characteristic impedance set to 65Ω ±10%. ◆Switchable between 33/66MHz. (Set to 66MHz at shipment) ◆GA〔0:4〕 can be set by the user. (Set according to specifications at shipment) ◆Standard equipped with "Type AB" shroud for rear transition module. (RP3, RP5) Also, standard equipped with coding key (brown) for all slots. (RP4) ◆Standard equipped with V (I/O) power switching bus bar. (Set to +3.3V at shipment) Also, standard equipped with coding key (yellow) for all slots. (P1) ◆FG-SG connection can be switched using backplane fixing screws.

• Embedded Board Computers

<Specifications> ◆Number of Slots: 4 slots / 6 slots / 8 slots ◆Backplane: CompactPCI backplane (3U R2.1) ◆Power Configuration: +5V 25A, +3.3V 16A, +12V 15A, -12V 0.5A ◆Others: Brackets for disk mounting (2 types), with AC cord <Features> ◆CPCI rack system offered as an ultra-low-cost development tool. ◆All components comply with standards for a high-performance rack system. (Backplane compliant with PICMG2.0 R2.1 ATX12V Ver1.3) ◆Various drive units can be easily installed. ◆The system slot is standard on the right side. ◆Cooling fan installation is available as an option.

• Development support tools (ICE, emulators, debuggers, etc.)
• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) 　　　　　　+5V, +3.3V, +12V, -12V, GND ◆Check Terminals: PRST, DEG, FAL, GND, IPMB-SCL, PMB-SDA, IPMB-PWR <Features> ◆Complies with PICMG2.0R2.1 standards. ◆Does not sacrifice peripheral slots when using a bridge. ◆Interrupt signals and board addresses can be set arbitrarily. ◆Hot swap compatible. (PICMG2.1) ◆M66EN can be supported with resistors. (Set to 33MHz at shipment) ◆Compatible with Bus Bridge Module PICMG2.6.

• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 12-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) 　1. Screw Terminal (18A per terminal), +5V, +3.3V, +12V, -12V, GND 　2. ATX Power Connector (optional support) 　3. 15-pin DIN Connector (optional support) <Features> ◆Compliant with PICMG2.8 (PXI Bus) standards. ◆Signal line characteristic impedance set to 65Ω ±10%. ◆System slot is 1 slot (left side), trigger slot is located at the 2nd slot. ◆V (I/O) voltage can be switched via bus bar. ◆Standard equipped with electrical specifications defined by the PXI bus, including 10MHz reference clock, PXI local bus, and PXI start trigger bus.

• Other process controls
• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (Halogen-free boards are also available) (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw terminal (18A per terminal) +5V, +3.3V, +12V, GND ◆Check Terminals: PRST, DEG, FAL, +5V, GND ◆Others: M66EN can be supported depending on the presence or absence of 0Ω resistors <Features> ◆Complies with PICMG2.0R3.0 standards. ◆Mechanically compatible with our PICMG2.0R2.1 standard backplane due to common external dimensions. ◆The CLK line is wired 1-to-1 from the system slot to each peripheral slot. ◆Signal line impedance is set to 65Ω ±10%. ◆In the 8-slot type, a long-type connector is installed in the slot farthest from the system slot, allowing for the installation of an off-board terminator (optional). ◆If used in conjunction with a bus module bridge, please contact our sales department.

• Embedded Board Computers

<Specifications> ◆Operating Voltage: 3.3V (Max 2.1W @ 33MHz) ◆Data Bus: Primary 64-bit, Secondary 64-bit ◆Board: Epoxy Glass (FR-4, 1.6t, 8-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Signal Line Characteristic Impedance: 65Ω ±10% ◆Operating Environment: During Operation: Temperature 0–60°C, Humidity 5–95% (No condensation at 40°C) During Storage/Transport: Temperature -40–+70°C, Humidity 0–95% (No condensation at 40°C) <Features> ◆Expansion on the secondary side is possible up to 7 slots. ◆The power layers are divided between the primary and secondary sides, allowing V (I/O) voltage to be set for each segment. ◆The GND layer is connected directly between the primary and secondary. ◆Slot expansion is possible from the bottom side to the top side without sacrificing slots. (Compatible with our bridge-supported type backplane.)

• Embedded Board Computers

**Packet Switching Backplane** <Specifications> ◆ Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆ Connector: IEC1076 (2mm Hard Metric) ◆ Power Supply Method: Screw Terminal, ATX Power Connector ◆ Check Terminals: PRST, DEG, FAL, IPMB <Features> ◆ Complies with PICMG2.16R1.0, PICMG2.0R3.0, and PICMG2.1R2.0 (Hot Swap) standards. ◆ Compatible connectors for PICMG2.9R1.0 (SMBus) available (optional). ◆ Supports 2 Fabric Slots (Slot Numbers 1, 2) Supports 6 Node Slots. ◆ System Slot (Slot Number 8) can be used as a Node Slot. ◆ RP3 and RP5 come standard with Type AB Shroud. ◆ V (I/O) voltage can be switched between 5V and 3.3V. ◆ Custom development and manufacturing available, including types that support high-frequency characteristics (low dielectric constant).

• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 12 layers) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) +5V, +3.3V, V (I/O), +12V, -12V, GND, FG Telecom Power (-Vbat/-SELVbat) Telecom Ringing Voltage (VRG) ◆Check Terminals: PRST, DEG, FAL ◆Signal Line Impedance: 65Ω (±10%) <Features> ◆System slot is arranged on the light side (right system) ◆System slots P3/P4/P5 can accommodate rear I/O modules (IEEE1101.11) ◆Peripheral slot P3 can be used as user I/O ◆V (I/O) power switching bus bar is standard equipped (default is +5V) ◆+5V and CT coding key are standard equipped ◆Signal line termination is standard equipped (for 8-slot products) ◆Various jumper post arrangements for settings ◆Optional additional power supply terminals can be installed (Faston terminals) ◆GND - Earth (FG) connection is possible ◆Optional implementation of "Type AB" shroud is available

• Communications

<Specifications> ◆Number of slots: 11 slots ◆Power configuration: +5V 30A, +3.3V 10A, +12V 4.2A, -12V 0.9A ◆Cooling method: 3 DC fans ◆Others: Noise filter, switch, fuse, FG terminal, AC cord included <Features> ◆All functions are included except for the module board. ◆The backplane is optional. ◆The power supply uses a plug-in method (implemented in a 9-slot size). ◆The structure complies with IEEE1101.10 (dot ten) and is equipped with EMC/ESD measures. ◆When the side frame (optional) is installed, it becomes a rack-mount type. ◆Fan wiring is supplied from -12V (compatible with all rack products). *Please inquire separately about the cost of DC supply wiring when implementing the optional backplane.

• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw terminal (18A per terminal); +5V, +3.3V, +12V, -12V, GND ◆Check Terminals: PRST, DEG, FAL, +5V, GND ◆Others: M66EN can be supported by pattern cutting <Features> ◆Complies with PICMG2.0R2.1 standards. ◆Hot swap compatible. (PICMG2.1R1.0) ◆The characteristic impedance of the signal lines is set to 65Ω±10%. ◆System slots are available on both the left and right sides. ◆In the 8-slot type, a long-type connector is implemented in the slot farthest from the system slot, allowing for the installation of an off-board terminator (optional). ◆P3-P4-P5 can be used for user I/O and rear I/O module implementation. ◆Power supply terminals can be expanded with options. (Using Faston terminals) ◆VIO power switching bus bar is standard equipped. (Set to +5V at shipment) ◆Optionally, "Type AB" shroud can be implemented.

• Embedded Board Computers

<Specifications> ◆Material: Substrate / Epoxy glass (FR-4, 1.6t, 6-layer board) ◆Compatible substrate size: H = depends on rack size. D = maximum 130mm ◆Compatible rack: 3U or 6U size rack (D = 160mm) ◆Pattern: Power conforms to PCI Local Bus Specification R2.1 and PICMG 2.0 R3.0 regulations <Features> ◆ Easily use commercially available 32-bit/5V compatible PCI cards with compact PCI. ◆ Depth up to a maximum of 130mm. Height depends on rack size. ◆ Standard equipped with IEEE 1101.1/.10 handles. ◆ Stub resistors (10Ω) placed on signal lines.

• Embedded Board Computers

<Specifications> ◆Material: Substrate / Epoxy glass (FR-4, 1.6t, 6-layer board) Rail bracket / Aluminum Guide rail / Noryl resin (UL94-VO) ◆Compatible substrate size: H=233.3mm, D=160mm ◆Compatible rack: 6U size rack (D=160mm) ◆Pattern (inner layer): Power pins comply with PICMG2.0R2.1, 64-bit compatible Other than power, parallel wiring <Features> ◆The characteristic impedance of the signal line is set to 65Ω±10%. ◆Signal termination can be achieved by attaching an off-board terminator (optional) to the check terminal section. ◆Voltage check test pins are implemented, making voltage verification easy. ◆With ejector and injector functionality, insertion and removal from the rack is easy. ◆The test board allows for easy insertion and removal due to the adoption of guide rails.

• Embedded Board Computers

<Specifications> ◆Material: Base board / Epoxy glass (FR-4, 1.6t, 6-layer board) Rail bracket / Aluminum Guide rail / Noryl resin (UL94-VO) ◆Compatible board size: H=100mm, D=160mm ◆Compatible rack: 3U size rack (D=160mm) ◆Pattern (inner layer): Power pins comply with PICMG2.0R2.1, 64-bit compatible Other than power, parallel wiring <Features> ◆The characteristic impedance of the signal line is set to 65Ω±10%. ◆Signal termination can be achieved by attaching an off-board terminator (optional) to the check terminal section. ◆Voltage check test pins are implemented for easy voltage verification. ◆The ejector/injector function allows for easy insertion and removal from the rack. ◆The test board utilizes a guide rail for easy insertion and removal.

• Embedded Board Computers

<Specifications> ◆Number of Slots: 4 slots ◆Power Configuration: +5V 30A, +3.3V 10A, +12V 3.6A, -12V 1.3A ◆Cooling Method: 2 DC fans ◆Others: Noise filter, switch, fuse, FG terminal, AC cord included <Features> ◆All functions except for the module board are included. (Including backplane) ◆Double height, 4 slots with horizontal mounting. (CPU module with 2-slot width can be mounted) ◆When a side frame (optional) is attached, it becomes a rack mount type. ◆By removing the top cover, CPU module debugging is possible without an extender. ◆The system slot is standard on the upper right side as a system type. ◆Mounting disks and other components is also easy. (Optional) ◆EMC/ESD measures are implemented. *Since mounting disks and other components is easy, please contact our sales department.

• Embedded Board Computers

<Specifications> ◆Operating Voltage: 3.3V (Max 2.1W @ 33MHz) ◆Data Bus: Primary 64-bit, Secondary 64-bit ◆Board: Epoxy Glass (FR-4, 1.6t, 8-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Signal Line Characteristic Impedance: 65Ω ±10% ◆Operating Environment: During Operation: Temperature 0-60℃, Humidity 5-95% (No condensation at 40℃) During Storage/Transport: Temperature -40 to +70℃, Humidity 0-95% (No condensation at 40℃) <Features> ◆Expansion on the secondary side is possible up to 7 slots. ◆The power layers are split between the primary and secondary sides, allowing V (I/O) voltage to be set for each segment. ◆The GND layer is connected directly between primary and secondary. ◆Interrupt setting lines (INT signals) can be configured arbitrarily by the user. ◆Slot expansion is possible without sacrificing slots. (Compatible with our bridge-supported type backplane.)

• Embedded Board Computers

<Specifications> ◆Power Configuration: (SSM-2030CW) +5V 30A, +3.3V 30A, +12V 8.5A, -12V 1.7A (SSM-2060CW) +5V 60A, +3.3V 60A, +12V 8.5A, -12V 1.7A (SSM-20ATCW) +5V 25A, +3.3V 16A, +12V 15A, -12V 0.5A ◆Cooling Method: 2 DC Fans ◆Others: Noise Filter, Switch, Fuse, FG Terminal, AC Cable Included <Features> ◆All functions except the module board are included ◆Structure complies with IEEE1101.10 (Dot 10) and is equipped with EMC/ESD measures ◆Rear I/O module board can be mounted from the back of the rack (compliant with IEEE1101.11) ◆Power supply can be used from AC100V to 264V, 50/60Hz ◆Easy installation of disks and other components ◆Disk bracket is standard equipped ◆When a side frame (optional) is installed, it becomes a rack mount type ◆Backboard is available as an option *Please inquire about the cost of DC supply wiring when a backboard is implemented.

• Embedded Board Computers

<Specifications> ◆Number of slots: 15 slots ◆Power configuration: +5V 30A, +3.3V 10A, +12V 4.2A, -12V 0.9A ◆Cooling method: 3 DC fans ◆Others: Noise filter, switch, fuse, FG terminal, AC cord included <Features> ◆Power configuration: +5V/30A, +3.3V/10A, +12V/4.2A, -12V/1.3A. ◆The power supply adopts a plug-in method. (Equipped with 6U, 5-slot size) ◆The structure complies with IEEE1101.10 and IEEE1101.11 and is equipped with EMC/ESD measures. ◆Rear I/O module boards can be mounted from the back side of the rack. ◆The cooling system is equipped with 3 DC fans. ◆Standard implementation of detachable side frames for rack mounting. ◆Supports backplane thickness t = 3.2mm. ◆Backplane support is available as an option. *Please inquire separately about the cost of DC supply wiring when implementing the optional backplane.

• Embedded Board Computers

<Specifications> (10 Slot Type) ◆ Number of Slots: 10 slots ◆ Power Configuration: +5V 30A, +3.3V 30A, +12V 3.5A, -12V 1.3A ◆ Cooling Method: 3 DC fans ◆ Others: Noise filter, switch, fuse, FG terminal, AC cord included (20 Slot Type) ◆ Number of Slots: 20 slots ◆ Power Configuration: +5V 60A, +3.3V 30A, +12V 4.2A, -12V 2.9A ◆ Cooling Method: 5 DC fans ◆ Others: Noise filter, switch, fuse, FG terminal, AC cord included <Features> ◆ All functions except the module board are included. ◆ The structure complies with IEEE1101.10 (Dot 10) and is equipped with EMC/ESD measures. ◆ The power supply can be used with AC 100V to 264V, 50/60Hz. ◆ Installing a side frame (optional) makes it a rack-mount type. ◆ The backplane is available as an option. ◆ The fan wiring is powered from -12V. *Please inquire separately about the cost of DC supply wiring when the optional backplane is implemented.

• Embedded Board Computers

<Specifications> ◆Number of Slots: 4 slots / 6 slots / 8 slots ◆Backplane: CompactPCI backplane (6U R2.1) ◆Power Configuration: +5V 25A, +3.3V 16A, +12V 15A, -12V 0.5A ◆Others: Brackets for disk mounting (2 types), with AC cord <Features> ◆Real panel I/O implemented for debugging. ◆All configured devices comply with standards for a high-performance rack system. (Backplane PICMG2.0 R2.1 ATX power supply ATX12V Ver1.3 compliant) ◆Various drive units can also be easily mounted. ◆The system slot is standard on the right side type. ◆Cooling fan installation is possible as an option.

• Development support tools (ICE, emulators, debuggers, etc.)
• Embedded Board Computers

<Specifications> ◆Number of slots: 8 slots ◆Backplane: CompactPCI backplane (PICMG2.0 R2.1 right system slot) ◆Power configuration: +5V 25A, +3.3V 16A, +12V 15A, -12V 0.5A ◆Others: Comes with AC cord (Material: zinc-coated) <Features> ◆A CPCI rack system that achieves ultra-low cost as an educational tool. ◆Open frame allows direct observation of board signals. ◆Electrostatic measures are implemented with alignment pins. ◆Cooling fan installation possible as an option. (2 fans, 92mm square)

• Development support tools (ICE, emulators, debuggers, etc.)
• Embedded Board Computers

<Specifications> ◆ Frame: Aluminum extruded material (white alodine treatment) ◆ Side Plate: Aluminum (white alodine treatment) ◆ Guide Rail: Noryl resin (UL94-V0) ◆ Insulator: Epoxy board (0.8t) <Features> ◆ Complies with IEEE1101.10 standards, allowing for the implementation of VME64Ext bus and CompactPCI bus modules. ◆ When a side frame (optional) is attached, it becomes a rack-mount type. ◆ The guide rail comes standard with ESD clips. * We can also accommodate requests for no ESD clips, so please contact our sales department.

• Embedded Board Computers

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw terminal (18A per terminal); +5V, +3.3V, +12V, -12V, GND ◆Check Terminals: PRST, DEG, FAL, GND, IPMB-SCL, PMB-SDA, IPMB-PWR <Features> ◆Does not sacrifice peripheral slots when using a bridge. ◆Interrupt signals and board addresses can be set arbitrarily. ◆Hot swap compatible. (R2.0) ◆M66EN can be supported with a resistor. (Factory setting is 33MHz) ◆Slot expansion can be freely configured in combination.

• Embedded Board Computers

<Specifications> ◆Material: Epoxy glass (FR-4 t=1.6 6-layer board) ◆Pattern: 2.54mm mesh pattern ◆Finished hole diameter: φ1.0 ◆Finishing treatment: Gold flash <Features> ◆This universal board is sized according to the CompactPCI standard, making it ideal for prototype evaluation. ◆The troublesome connectors are already mounted, improving workability. ◆It comes with a front panel and handle, allowing for immediate evaluation with actual equipment after completion. (Products with just the board are also available.) *We also accept processing for the front panel, so please contact our sales department for inquiries.

• Embedded Board Computers

<Specifications> ◆Material: Iron (black leather finish) ◆Dimensions: 481.0W × 43.4H × 295.4D ◆Power Supply: External supply from rear terminal block (DC12V) ◆Power Consumption: 40W ◆Mounted Fans: 6 alarm fans (DC12V specification) ◆LED Display: Off during normal operation, red light during abnormal operation ◆Order Codes: SMS-FAN-U for upward airflow, SMS-FAN-D for direct airflow <Features> ◆Equipped with 6 alarm fans (120mm square) ◆Each fan has an individual alarm LED (with alarm sensor board) ◆19-inch rack mountable ◆Side frame conforms to EIA standards (JIS standards can also be customized) ◆Compact size of 1U ◆Two types of airflow available: upward and direct

• Embedded Board Computers