タートル工業 List of Products and Services

This unit is a USB interface DA converter with a resolution of 14 bits and a conversion rate of 1 MHz. The analog output has 2 channels with BNC connectors, allowing for continuous waveform output without limitation in combination with FIFO memory and USB, in addition to high-resolution DC voltage output. It can also be used as a variable reference voltage source, function generator, arbitrary waveform generator, etc. Please note that this product is a budget version of the TUSB-0416DAM.

• converter

This unit is a high-performance DA converter unit (USB connected) with a resolution of 16 bits and a conversion rate of 1 MHz. The analog output features 4 channels with BNC connectors, allowing for continuous waveform output without limitation, thanks to the combination of high-resolution DC voltage output, FIFO memory, and USB interface. In addition to a variable reference voltage source, it can also be used as a function generator and arbitrary waveform generator, and it is adopted by major manufacturers. - Main Features - ■ Number of output channels: 4ch (2ch × 2 groups) ■ Quantization resolution: 16bit ■ Non-linearity: within 2LSB ■ Maximum output voltage: ±10V ■ Output range: 0–10V, 0–5V, ±2.5V, ±5V, ±10V

• Other electronic parts

Our 16ch AD converter: TUSB-1612ADSM-S2Z is a dedicated input/output adapter. Even more than ten years after its development, the TUSB-1612ADSM-S2Z continues to receive support from many users and is utilized in various fields alongside the TUSB-0412ADSM-S2Z (4ch BNC type). The input of the TUSB-1612ADSM-S2Z connects using a conventional flat cable connector. By using the T-ADP02C, you can convert from the flat cable connector to BNC, making the connection easier.

• Other electronic parts

This is a compact, lightweight, and low-cost high-voltage output amplifier (amplifier). It has a fixed gain of 300 times, with an output voltage range of up to -3kV to +3kV. The frequency characteristic ranges from DC to a maximum of 2kHz, and it can drive a load with an output current of up to ±2mA. Additionally, it features an output signal monitor terminal for easy confirmation of the output voltage. It is equipped with mounting holes and comes with bare wire input/output cables, making it suitable for integration. 【Features】 ■ Compact, lightweight, and low-cost high-voltage output amplifier (amplifier) ■ Maximum output voltage: -3kV to +3kV (6kVpp) ■ Frequency characteristic ranges from DC to a maximum of 2kHz, with an output current of up to 2mA to drive loads ■ Easy confirmation of output voltage with an output signal monitor terminal *For details, please contact us or view the PDF data available for download.

• Amplifier

This unit (TWL-S01LC) and the master unit connected to a computer (TUSB-MNSTBP) allow for wireless measurement. Additionally, by preparing multiple units, a large-scale wireless communication system for load cells can be constructed. The load cells support both 6-wire and 4-wire configurations, and can switch between battery operation (using two AA batteries) and 3.3V external power supply. Once the software is set up on the computer, measurements can be started immediately. An optional USB-powered repeater is also available.

• Pressure

This is a DC stabilized power supply with a wide input voltage range of 5V/2A. It is designed to minimize the pulsing noise characteristic of switching power supplies. The plug configuration is center negative.

• Switching Power Supply

Turtle Industrial Co., Ltd. is a group of engineers that has been engaged for many years in the development of various control and measurement devices and systems utilizing electronic circuit technology and computer technology. In recent years, anticipating that USB would become the standard interface for personal computers, we quickly began developing measurement and control peripheral devices with USB interfaces, which we sell at high performance and low prices. Additionally, by applying analog circuit technology, we have commercialized various amplifiers and filters, selling them at low prices, thus contributing to measurement and control in this field. In this document, we introduce: ● LAN connection devices ● USB-IF products ● Analog amplifiers ● Analog filters ● Power supplies ● Software ● Other custom-made products, etc. If you are interested, please download our comprehensive catalog in PDF format.

• Other electronic parts
• Instrumentation and Control Systems
• Amplifier

It can be easily connected to the installed LAN, allowing for the input and identification of four sets of voltage-free contact signals to the PC. It supports PoE (Power over Ethernet) and can be operated without being connected to a power source. It can also be mounted on a DIN rail, and no tools such as drivers are required for wiring connections, making installation simple. It is suitable for factory production equipment, power facilities, and large-scale facilities.

• Other electronic parts

At the request of our customers, we also offer customization for amplifiers that amplify specified frequencies in the range of 50MHz to 300MHz. Users can easily amplify high-frequency signals by simply connecting a DC+5V power supply and input/output signal cables, without the need to design high-frequency circuits. It is equipped with a noise-resistant series regulator power supply. Additionally, a third-order LC filter allows for frequency specification and bandwidth limitation, enabling not only the amplification of the required signals but also the reduction of unwanted signals and noise levels. - Model number without filter: T-SHFA01C - Model number with filter: T-SHFA01FC

• Amplifier
• High frequency/microwave parts

At the request of our customers, we also offer customization for amplifiers that amplify specified frequencies in the range of 50MHz to 300MHz. Users can easily amplify high-frequency signals by simply connecting a DC+5V power supply and input/output signal cables, without the need to design high-frequency circuits. Additionally, with a third-order LC filter, we can specify frequencies and limit bandwidth, allowing us to amplify the necessary signals while reducing unwanted signals and noise levels. - Model number without filter: T-SHFA01 - Model number with filter: T-SHFA01F

• High frequency/microwave parts
• Amplifier

This is a measurement and analysis software developed by Matsuyama Advance Co., Ltd. It has various features such as configuration settings for recording device composition, execution condition settings for recording, support for two types of scaling, compatibility with various file formats, various digital filters like low-pass and high-pass, and the generation of various signal waveforms such as sine waves and square waves. It is compatible with Windows 7, 8, 10, and 11.

• Data Logger

Our A/D converter: TUSB-K02ADVZ is convenient for input signal offset cancellation and adjustment, or for DC component adjustment of the output signal of the D/A converter: TUSB-K01DAZ. It can be easily fixed with the same mounting holes and pitch as the above two products.

• Amplifier

Embedded A/D converter: By combining TUSB-K02ADVZ and D/A converter: TUSB-K01DAZ, it becomes easy to capture small signals and provide the necessary voltage output. The phase between input and output can be selected as normal or inverted. The mounting holes are located in the same position as the above A/D and D/A converters, making it easy to secure to the circuit board.

• Amplifier

The 24-bit AD converter unit 'TUSB-0224ADM' is a measurement and control tool designed with the user in mind, achieving high performance at a low price. It features a resolution of 24 bits, a sampling rate of 256 kHz, and simultaneous conversion of 2 channels with a USB interface. It offers a wide dynamic range, ultra-low noise, and long-term continuous data acquisition through a combination of FIFO memory and HS (High-Speed) USB, making it highly functional and high-performance. Its applications extend to fields such as space, civil engineering measurement, and audio measurement. <Features> - 24-bit resolution - 2 channels (simultaneous, BNC connector) - Maximum sampling rate of 256 kHz (internal sampling clock) - Sampling data is transferred sequentially to the PC for data recording * Maximum acquisition length is determined by PC software and hardware - Interface: USB High-Speed (480 Mbps) - Dimensions: 30 mm (height) × 100 mm (width) × 140 mm (depth, excluding protrusions) - Weight: Approximately 345 g (excluding connection cable) For more details, please download the PDF or feel free to contact us.

• Other measurement, recording and measuring instruments

This is a high-resolution, ultra-fast 16-bit/25MHz AD converter unit. It is equipped with two ADCs, allowing for high-speed conversion on two channels simultaneously. The large-capacity memory uses FIFO method, enabling data transfer to a computer while AD conversion is in progress. Furthermore, taking advantage of the large-capacity memory, it allows for repeated capture of AD conversion start and stop, and memory usage can also be monitored.

• Other FA equipment

The 16-bit AD converter unit "TUSB-0216ADMZ" is an AD converter unit that can convert analog electrical signals into digital electrical signals. It is a high-resolution, high-speed, high-function, and low-cost A/D converter. It features simultaneous conversion of two channels at a maximum of 100kHz, continuous data transfer, multi-range input, a resolution of 1/65536 (16 bits), FIFO large-capacity memory, external clock input, various trigger methods, and a USB interface that eliminates the need for a power supply, among many other characteristics of a high-performance AD converter. Furthermore, when combined with the measurement analysis software LaBDAQ6-TL (manufactured by Matsuyama Advance Co., Ltd.), advanced data analysis can be easily performed. Each unit is tested before shipment, ensuring reliable use. ★ For custom products and prototype development, please leave it to Turtle Industries ★ We accept commissioned development of custom products and prototypes for various measurement and control devices. Please feel free to contact us.

• Other FA equipment
• Voltage Meter

■Supports any voltage level input with a programmable multi-input range Each channel can independently set the input range ■Long-term continuous data acquisition possible with 256K sample large capacity FIFO memory ■User-friendly with a rich set of trigger functions ■High-speed conversion at 100KHz ■Compact and lightweight ■Becomes a high-performance data logger with the data logger software TUSB-DLGS ■Demonstrates excellent functionality when combined with the measurement analysis software LaBDAQ-PRO TL (manufactured by Matsuyama Advance) ■Complies with RoHS directives

• Other FA equipment

■ The input uses a very user-friendly BNC connector, with the minimum necessary number of 4 channels. ■ Adopts a programmable multi-input range, allowing independent setting of the input range for each channel. ■ High-speed conversion at 100KHz. ■ 256K sample large capacity FIFO memory. ■ Long-term continuous data acquisition is possible due to high-speed transfer. ■ A rich variety of user-friendly trigger functions.

• Other FA equipment

This is a high-speed voltage data logger with a USB interface. With dedicated acquisition software, data sampling can be executed immediately. It supports high-speed sampling of up to 100kSPS and can acquire 60,000,000 data points. The gain of the input amplifier is switchable with a maximum of 100 times. 【Features】 - Easy connection to a computer via USB interface - Immediate data sampling possible with dedicated acquisition software - Supports high-speed sampling of up to 100kSPS - The gain of the input amplifier is switchable with a maximum of 100 times, allowing for direct acquisition of weak voltage signals. *For details, please refer to the PDF catalog available for download.

• Voltage Meter

It has 8 channels of input, and the voltage range can be set for each channel. By connecting to a LAN, voltage measurements can be taken from a remote location. For AC voltage measurements, it employs a true RMS conversion method that is less affected by waveform variations compared to other methods, allowing for highly accurate measurements.

• Voltage Meter

It has sufficient bandwidth and gain as a preamplifier (amp) for high-speed A/D converters. It features a 50Ω differential output, allowing for matched connection with a 50Ω load, enabling accurate waveform transmission. Its compact and lightweight design makes it easy to use without being limited to specific installation locations.

• Other FA equipment

As a preamplifier for high-resolution AD converters, it plays an active role in amplifying weak signals such as those from optical sensors, acoustics, and vibrations in many situations. It features a compact and lightweight design, is reasonably priced, and is battery-operated (cable-free).

• Amplifier

This device is a wideband isolation amplifier with a passband width from DC to 1 MHz. The isolation is achieved through a linear optical method, eliminating the spike noise commonly found in typical isolation amplifiers, allowing for remarkably quiet signal transmission. By using this amplifier, you can completely isolate analog signals without being troubled by noise. The isolation voltage between input and output is also very high, making it suitable for a wide range of applications. The signal input and output are configured for ease of use with BNC connectors. Each unit is tested before shipment, ensuring reliable performance.

• Amplifier

The "T-HVA02" is a compact high-speed DC amplifier with an output voltage of 600Vpp. It has a maximum output current of 100mA, providing ample capacity for various applications. It features an "offset adjustment function with a fine-tuning dial," and operates within a temperature range of 5°C to 35°C. With a slew rate of 400V/μs, it also excels in large amplitude response. 【Features】 ■ Equipped with protection functions using overcurrent and overtemperature sensors ■ Includes a ±50V output offset function ■ Custom specifications can also be accommodated *For more details, please refer to the catalog or feel free to contact us.

• Other measurement, recording and measuring instruments

Low-cost DC amplifier with high speed and high voltage output. Suitable for experiments and measurements, such as driving piezoelectric elements. ● Number of channels: 1 channel ● Input resistance: 1 MΩ ● Gain: 10 times ● Maximum output voltage: approximately ±100 Vp ● Maximum output current: approximately ±0.2 Ap

• Amplifier

- A voltage of several hundred volts is not needed, but it is optimal when the output of the OPAMP at ±12V/10mA is insufficient. - Maximum output voltage: ±40V - Maximum output current: ±50mA - Number of input channels: 1ch (both input and output use BNC connectors) - Input resistance: Non-inverting 60KΩ ±2% (Inverting 10KΩ ±1%) - Allowable input voltage: ±40V

• Other machine elements

Because the isolation transmission is linear, there is no spike noise typically seen in general isolation amplifiers, allowing for an astonishingly quiet signal transmission. Therefore, it is possible to completely isolate analog signals without being troubled by spike noise.

• Printed Circuit Board
• Embedded Board Computers

The ultra-high-speed I/V converter (current-to-voltage converter) T-IVA001HS features a current-to-voltage conversion rate of 10G[V/A] and 100G[V/A] with a switchable option, offering ultra-wideband characteristics from DC to 10kHz. Additionally, the output voltage is ±10Vpk. The existing product T-IVA001HZ had an upper limit of 2kHz, but in response to customer requests, we have achieved a high-speed model. This characteristic expands the range of measurement applications. Furthermore, it has been made smaller, lighter, and more affordable. *For more details, please download the materials or contact us.*

• Other measurement, recording and measuring instruments

It is a 4-channel unity gain differential amplifier with a high common-mode voltage range. It allows for channel number configuration with multiple units combined. By removing common-mode input voltages up to ±500V and extracting the differential voltage, the measurement system configuration becomes simpler. It is suitable for applications such as high-side current measurement, upper cell voltage measurement of multi-cell batteries, preamplifiers for AD converters, and replacement of isolation amplifiers.

• Amplifier

The 【T-PID01Z】 is an analog PID control board equipped with various input and output options and a potentiometer. Each monitor has a buffer amplifier and is equipped with potentiometers for setting the reference value and each PID level. It features monitor outputs for each PID level and both forward and reverse phase outputs. The reference value can be set using a potentiometer or voltage, and each PID setting can be switched to use an external potentiometer. A DC stabilized power supply, "T-VSR02-15Z," is also available to fully utilize its performance.

• Embedded Board Computers

It is possible to set the cutoff frequency for each channel and choose between low-pass and high-pass filters, making it a completely custom-made product tailored to the customer's requirements. It can be designed to have characteristics that perfectly match the intended use. This tool has a very wide range of applications, including noise reduction and bandwidth limitation during A/D conversion. It has a wide allowable range for power supply voltage and relatively low current consumption, making it operable on batteries. When combined with our T-VSR02-15Z power supply for AC100V, it allows for extremely low-cost system construction. It can be manufactured in a short lead time and comes with a characteristic measurement report for each unit.

• Other FA equipment

By incorporating ring memory, it is possible to generate arbitrary waveforms. Up to 16 units can be connected, allowing for multi-channel output.

• Other FA equipment

Despite being compact, lightweight, and low-cost, it has excellent features such as dual-axis output, isolated limit switch input, and the ability to synchronize multiple motors. Due to its reasonable price, it is also recommended for learning the handling techniques of pulse motors (stepping motors) as teaching materials.

• Embedded Board Computers

○ Ideal for situations such as "a little gain is lacking" or "wanting to convert impedance due to equipment constraints" in the production of measurement and control devices and systems. High-performance operational amplifiers that meet these demands. ○ Four types of lineup according to application: ・T-AMP01/T-AMP01B Typical amplifier circuit board using a single OPAMP stage. ・T-AMP02/T-AMP02B Typical amplifier circuit board using a two-stage OPAMP. ○ Custom-made options are also available.

• Printed Circuit Board

○ Ideal for situations such as "a bit more gain is needed" or "want to convert impedance due to equipment constraints" in the production of measurement and control devices and systems. High-performance operational amplifiers that meet these requirements. ○ Three types of lineup according to application: [T-AMP03] Amplifier circuit board with output buffer for output current enhancement. [T-AMP04] OPAMP single-stage amplifier circuit, dual-channel board. [T-AMP05] Amplifier circuit board with input buffer for increased input resistance and reduced noise. ○ Board dimensions: 74×43×1.6mm ○ Mounting holes: φ3.4×6 ○ Mounting hole pitch: 54×33mm ○ Custom-made options are also available.

• Printed Circuit Board

○ Ideal for situations such as "a little gain is lacking" or "wanting to convert impedance due to equipment constraints" in the production of measurement and control devices and systems. High-performance operational amplifiers that meet these requirements. ○ Two types are available according to application: [T-AMP06] Feedback and other multi-purpose OPAMP amplifier circuit board. [T-AMP07] Voltage level offset and other multi-purpose OPAMP amplifier circuit board. ○ Board dimensions: 74×43×1.6mm Mounting holes: Φ3.2×6 Mounting hole pitch: 54×33mm, etc. ○ Custom-made options are also available.

• Printed Circuit Board

○ Ideal for situations such as "a little gain is lacking" or "I want to change the impedance due to equipment constraints" in the production of measurement and control devices and systems. High-performance operational amplifiers that meet these requirements. ○ Two types available according to application: [T-AMP08] 12dB or 18dB/OCT LPF or HPF board [T-AMP-PS] Power supply board ○ Board dimensions: 90 (or 74) × 43 × 1.6 mm Mounting holes: Φ3.2 × 6 Mounting hole pitch: 54 × 33 mm, etc. ○ Custom-made options are also available.

• Printed Circuit Board

○ Ideal for situations such as "the gain is a bit insufficient" or "I want to change the impedance due to equipment constraints" in the production of measurement and control devices and systems. High-performance operational amplifiers that meet these requirements. ○ Two types are available in the lineup according to application: [T-AMP09] Absolute value circuit (full-wave rectifier circuit) [T-AMP11] Differential input measurement amplifier, with variable resistor for common mode rejection and variable resistor for offset setting of each OP-AMP. ○ Custom-made options are also available.

• Printed Circuit Board

It amplifies small signals to a sufficiently large size. This amplifier has sufficient performance while being very affordable and easy to use. The power supply operates on a direct current voltage, allowing it to function with batteries, and its compact and lightweight design makes it suitable for outdoor use and various locations. All units are tested before shipment, ensuring reliable use. 【Features】 ■ Differential input reduces common-mode noise ■ Gain selectable from 1x to 10,000x ■ Power supply uses a reasonable single DC input method, making battery operation easy ■ Complies with RoHS directives *For more details, please request documentation or view the PDF data available for download.

• Other machine elements
• power supply

It amplifies small signals to a sufficiently large size. This amplifier can be used easily at a very low price while having the necessary and sufficient performance. Since the power supply is a direct current voltage supply method, it can also operate on batteries. Combined with its compact and lightweight design, it can be used in various locations, including outdoors. All units are tested before shipment, so you can use them with confidence.

• Other machine elements
• power supply

It amplifies small signals to a sufficiently large size. This amplifier can be easily used at a very low price while having the necessary and sufficient performance. Since the power supply is a direct current voltage supply method, it can also operate on batteries. Its compact and lightweight design allows for use in various locations, including outdoors. All units are tested before shipment, ensuring you can use them with confidence.

• Other machine elements

This is a board with a screw terminal block that makes it easy to connect to external circuits. Furthermore, it has a very large universal area, allowing for the installation of components such as photo couplers, relays, and SSRs according to your intended use. Includes a 0.5m cable for connection to TUSB-PIOZ.

• Printed Circuit Board

Introducing the counter AC/high voltage input adapter manufactured by Turtle Industrial Co. ■ Two types of products available ・T-ADPCN01Z (discontinued) Used for relatively low voltage high frequency (DC to 1MHz) input with a BNC connector. ・T-ADPCN02Z Uses a screw terminal block for safe and easy connection to high voltage low frequency (DC to 2KHz) circuits, and ensures safety with complete insulation.

• Other machine elements

The power supply is single and can also be used with batteries. Capacitors for conversion with capacitance other than 1000pF (standard) can be manufactured (for a fee). It complies with the RoHS directive, expanding its range of use. Furthermore, when using two or more units connected to the common 0V line from a single power supply, be sure to include a decoupler. Power decoupling: T-02ADPVD01 is also available for sale.

• Amplifier

The insulation uses a linear method based on light, resulting in no spike noise and transmitting signals with astonishing quietness. This device allows for complete insulation of analog signals without being troubled by noise. The signal input and output use BNC connectors, while the power input employs reliable metal connectors.

• Other FA equipment