Aiming for Zero Workplace Accidents! How to Choose the Right Protective Gloves [Environmental Measures VOL.8]

This will focus on cut injuries and chemical damage, which are believed to be common not only in labor accidents but also in near misses, explaining the characteristics of protective gloves and their proper usage.

Work that requires protective gear occurs not only in manufacturing but also in various industries. Among the many types of protective equipment, gloves in particular come in a wide variety, and there may be cases of improper use, reuse, or even instances where protective gloves are not used despite the work being hazardous. However, allowing such situations to persist leads to neglecting the "unsafe behaviors" and "unsafe conditions" discussed in VOL.3, which increases the likelihood of workplace accidents. In 2023, "cuts and abrasions" ranked 5th (5.61%) in workplace accidents, while "contact with harmful substances" ranked 13th (0.45%). However, there are likely many more near misses that did not result in accidents. This time, we will focus on the more frequent incidents of cuts and chemical injuries, discussing the characteristics of different types of protective gloves and the proper methods for their use.

• Other consumables
• Work gloves
• Other safety and hygiene products

We will introduce the basics of risk assessment and safety protective equipment to ensure the safety of workers.

Since 1988, the number of casualties from labor accidents has been decreasing, but since 2000, the situation has remained stagnant. In White Paper Vol. 2 [Winter Season Sees a Surge, Preventing Falls Before They Happen], we addressed the causes and preventive measures for falls, which are the most common type of labor accident. But why do labor accidents occur in the first place? This time, I would like to focus on protecting the safety of workers and discuss the mechanisms behind labor accidents and their prevention.

• Other consumables
• Work gloves
• Other safety and hygiene products

The Ministry of Health, Labour and Welfare has established new regulations to prevent labor accidents caused by chemical substances.

Starting from April 1, 2024, it has become mandatory for workplaces that handle chemical substances such as sodium hypochlorite (bleach), sodium hydroxide, and potassium hydroxide to require the use of protective eyewear. 【Details of the New Regulations】 ■ Workplace Structure 1. Workers handling chemical substances must wear appropriate protective gear, such as protective eyewear. 2. Establish a system for self-management. (1) Appoint a chemical substance manager. (2) Appoint a protective gear management supervisor. ■ Prevention of Direct Contact with Harmful Chemical Substances When engaging workers in tasks that involve manufacturing or handling chemical substances that are skin or eye irritants, corrosive to skin, or can be absorbed through the skin and cause health issues, it is necessary to require workers to use protective gear to prevent injuries, depending on the harmfulness of the substances. For more details, please refer to the materials.

• Other consumables
• Glasses and goggles
• Other safety and hygiene products

Compatible with a wide range of solvents. Can be used as inner gloves.

【Features】 ■Compatible with a wide range of solvents ■Ambidextrous disposable type ■Can be used as inner gloves ■European standards EN420/374 *For more details, please refer to the PDF document or feel free to contact us.

• Work gloves

A cutter with a safety design that automatically retracts the blade when cutting is finished. It's a precaution against accidents when cutting cardboard and packaging materials!

The safety cutter "SecuPro 625" solves the problem of cutting thick materials like cardboard, where "it's hard to cut without applying force," but "applying force increases the risk of cutting accidents." The "SecuPro 625" is designed so that the blade does not extend unless held. 【Features】 ■ The blade automatically retracts into the body when it is away from the material being cut. ■ Durable aluminum body. ■ Left-handed compatible. * For more details, please refer to the PDF document or feel free to contact us. * A video demonstrating how the blade automatically retracts is available.

• Cutter/Scissors

Thin chemical-resistant gloves made with three types of materials and featuring three characteristics!

"Try Lights" are gloves made from three types of materials: natural latex, neoprene, and nitrile, each possessing the three characteristics of "stretchability," "chemical resistance," and "durability." The surface is embossed, making them effective for tasks such as cleaning where items are easily dropped. As thin gloves, they offer a wide range of chemical resistance and serve as excellent inner gloves for chemical work that requires thicker gloves. 【Features】 ■ Three types of materials providing "stretchability," "chemical resistance," and "durability" ■ Slip-resistant processing ■ Wide range of chemical resistance ■ No water-resistant powder ■ Surface treated with chlorine for sterilization ■ FDA (U.S. Food and Drug Administration) certified *For more details, please refer to the PDF document or feel free to contact us.

• Work gloves

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.

Are you struggling to explain "safety" to the client using just drawings? - The risks in blind spots are difficult to convey to the client through drawings alone. - Safety measures often become a target for cost reduction, making it hard to communicate their necessity. - There is a concern that the client might say, "It's more dangerous than I thought," after completion. Risks that are visible to design professionals are not easily understood intuitively by clients who are outside the field. This document is not just a simple explanation of sensor functions; it is a guide to visually explain "why sensors are necessary in that location." It can be used directly as explanatory material for the client. Here are three key points for utilizing this document: 1. Visualization of Risks Blind spots during vehicle departure and contact risks within the site are illustrated clearly. 2. Clarification of Selection Criteria A comparison table outlines the differences between complex sensor types such as infrared, ultrasonic, and loop coils. 3. Diagram of System Configuration It illustrates not just the sensors alone, but how they combine with components like rotating lights and control panels, providing practical assistance for electrical equipment design. Please make use of this to prevent "rework after completion" and "accident risks."

In facilities operating nurse call systems, we have made the bed exit sensor wireless, allowing it to notify in conjunction with the nurse call system. By simply connecting the mat sensor "Foldable Thin Matt-kun," the body movement call "Ugo-kun," and the wheelchair body movement call "Ayumi-chan" to the transmitter HB-RS, you can make the bed exit sensor wireless. The infrared sensor "Just Place Pole-kun" has the transmitter HB-RS built-in. This helps prevent accidents caused by falls, slips, or wandering, contributing to the efficiency of medical operations. 【Features】 ○ Wireless conversion by simply connecting existing sensors to the transmitter HB-WSK. ○ The bed exit sensor notifies wirelessly in conjunction with the nurse call system. ○ Up to 5 transmitters can be registered with a single receiver. ○ The communication distance between the transmitter and receiver is approximately 10 meters. ◎ For more details, please contact us or download the catalog.