[New Product] FeliCa/Mifare Compatible! Outdoor-Compatible Contactless Card Reader [ST-530MF]

Universal card reader compatible with FeliCa and Mifare.

**Features** - Standalone non-contact card reader, no network connection required - Outdoor compatible (IP64) - Unlock methods: PIN code/card key (Up to 8 PIN codes and 2,000 cards can be registered) (Card keys support both FeliCa and Mifare) - Four selectable operation modes (Card only/PIN code only/Card or PIN code/Card and PIN code) - Compatible with DC12V/DC24V, can be integrated into systems with other devices *For more details, please refer to the PDF document or feel free to contact us.*

• Other security and surveillance systems

Waterproof small electromagnetic lock, standard product of electromagnetic electric lock / Rated voltage: DC12/24V compatible, holding force: 200Kg

◯ Product Features - A compact waterproof electromagnetic electric lock with a holding force of 200 kg, suitable for installation both indoors and outdoors. - Mounting screw holes are provided on the front and side, allowing installation from either the front or side. - A variety of mounting brackets are available for installation on various doors such as outdoor gates, sliding doors, and hinged doors. - Built-in locking signal (LSS) and door closed signal (DSS) allow for output of contact states for locking/unlocking and door open/close status. - Locking signal/door closed signal is provided on both sides, enabling a wide detection range for signals.

• Other security and surveillance systems
• Entrance and exit control system
• others

Dedicated control panel for VOLCALOCK, equipped with a DC12V/3.5A power supply unit.

This is a dedicated control panel for the LOCKMAN electromagnetic lock "VOLCALOCK series."

• Control Panel
• Entrance and exit control system

Waterproof standalone card reader. Suitable for indoor use as well as outdoor installation!

The "ST-120" is a waterproof, outdoor-installable card/PIN-based contactless card reader. The keypad lights up, allowing for safe operation even at night. Additionally, it can register up to 1,000 cards and supports up to 8 different PINs. 【Features】 ■ Waterproof standalone card reader ■ Can be installed indoors as well as outdoors ■ Keypad lights up for safe operation at night ■ Equipped with four modes ■ Compatible with EM-type IC cards, rated voltage is DC12V *For more details, please refer to the PDF document or feel free to contact us.

• Other security and surveillance systems

Unlock easily by simply bringing your hand close without touching the button! Non-contact unlocking switch. Ideal for indoor buttons of electric lock systems!

The "SI-68A" is a non-contact unlocking switch used in electric lock systems and similar applications. ◯ Product Features ■ It is a non-contact unlocking switch that can unlock simply by bringing your finger close, outputting a no-voltage contact. ■ It is ideal for use as an unlocking switch for electric locks when exiting from the inside, connected to a control panel. ■ The activation status of the unlocking switch can be confirmed with red and green LEDs. ■ The contact output time and sensing distance can be adjusted. ■ The plate features a simple design printed for the electric lock unlocking switch. *Note: This product is a weak contact switch designed to be connected to control panels, etc. If directly connected to devices with high current, such as electric locks, it may malfunction. Please be cautious with the connected devices. *For more details, please refer to the PDF materials or feel free to contact us.

• switch
• Safety Door Switch

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without affecting the base material with heat. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly creating sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or variations in dimensions, can be created in a single molding process. This allows for the verification of multiple types in a short period.