Technical Overview of the Welding Seam Detection Device "Roland SND40"

Welding seam detection device for pipes (up to 500mm in diameter), metal sheet coils, electric wires, and wires.

The Roland SND40 uses a non-contact eddy current and leakage magnetic flux sensor to detect weld seams on metal plates, both ferrous and non-ferrous, and can identify the position of welds on pipes with a diameter of up to 500mm. 【Benefits】 ◎ Detection of weld seams that cannot be recognized by visual sensors ◎ Utilizes two technological elements: magnetic flux and eddy currents * A full-surround coil that can also be used for metal rods, wires, and cables is available, accommodating a variety of materials. ● Additional technical data and specifications can be viewed from the 【Download】 section. The manufacturing of coil materials and other long materials (cables and wires) results in elongated products (metal coil materials are welded at the ends, and cable materials use joints), necessitating automatic detection of weld seams. In the case of tubes, cans, or drums, automatic detection of weld seams is required along with positioning of the material for further processing. For example, in the case of pipe materials, there is a signal output function that stops the seam position at a specified angle in preparation for the next bending process. The appropriate combination of sensors for the SND40 enables the detection of longitudinal weld seams in all metal tubes, cans, and drums, as well as the detection of end weld seams in coil materials, cables, and wire materials.

• Other processing machines
• Other inspection equipment and devices
• Visual Inspection Equipment

Insulating oil from old electrical equipment that has been in use for over 30 years may be contaminated with PCBs. Proper disposal is required by the disposal deadline. If you are using a vacuum tube oscillator, please check! - Transformers - Capacitors - Rectifiers, etc. Please consider updating any relevant equipment such as oscillators and hardening equipment as soon as possible. *For more details, please refer to the PDF document or feel free to contact us. ★ For inquiries by phone, please call: Osaka Headquarters → TEL: 072-991-1361 Nagoya → TEL: 052-322-1361 Tokyo → TEL: 03-5472-1361 ★ For inquiries by email, please contact: info@fujidenshi.co.jp *When calling or emailing, please mention that you saw this on "Ipros." Response hours: Monday to Friday, 9 AM to 5 PM.

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If you require a detailed technical explanation, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without affecting the base material with heat. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.