We have compiled a list of manufacturers, distributors, product information, reference prices, and rankings for Backboard.
ipros is IPROS GMS ・ IPROS One of the largest technical database sites in Japan that collects information on.

Backboard - List of Manufacturers, Suppliers, Companies and Products

Backboard Product List

16～26 item / All 26 items

Displayed results
CompactPCI-3U Backplane SPB-xxCx

CompactPCI-3U Backplane SPB-xxCx

CompactPCI-3U backplane (PICMG2.0 R2.1 compliant type)

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) +5V, +3.3V, +12V, GND ◆Check Terminals: PRST, DEG, FAL, +5V, GND ◆Others: M66EN can be supported by pattern cutting <Features> ◆Complies with PICMG2.0R2.1 standards. ◆The characteristic impedance of the signal lines is set to 65Ω ±10%. ◆System slots are available on both the left and right sides. ◆In the 8-slot type, a long-type connector is implemented in the slot farthest from the system slot, allowing for the installation of the off-board terminator STB-64C (optional). (Please inquire) ◆If used in conjunction with the bus module bridge, please contact our sales department.

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
CompactPCI-3U Backplane SPB-xxCER

CompactPCI-3U Backplane SPB-xxCER

CompactPCI-3U backplane (compliant with PICMG2.0 R2.1 and bridge-compatible type)

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) 　　　　　　+5V, +3.3V, +12V, -12V, GND ◆Check Terminals: PRST, DEG, FAL, GND, IPMB-SCL, PMB-SDA, IPMB-PWR <Features> ◆Complies with PICMG2.0R2.1 standards. ◆Does not sacrifice peripheral slots when using a bridge. ◆Interrupt signals and board addresses can be set arbitrarily. ◆Hot swap compatible. (PICMG2.1) ◆M66EN can be supported with resistors. (Set to 33MHz at shipment) ◆Compatible with Bus Bridge Module PICMG2.6.

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
CompactPCI-3U Backplane SPB-08PXI

CompactPCI-3U Backplane SPB-08PXI

CompactPCI-3U backplane (PXI bus compatible type)

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 12-layer board) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) 　1. Screw Terminal (18A per terminal), +5V, +3.3V, +12V, -12V, GND 　2. ATX Power Connector (optional support) 　3. 15-pin DIN Connector (optional support) <Features> ◆Compliant with PICMG2.8 (PXI Bus) standards. ◆Signal line characteristic impedance set to 65Ω ±10%. ◆System slot is 1 slot (left side), trigger slot is located at the 2nd slot. ◆V (I/O) voltage can be switched via bus bar. ◆Standard equipped with electrical specifications defined by the PXI bus, including 10MHz reference clock, PXI local bus, and PXI start trigger bus.

  • Other process controls
  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
CompactPCI-6U Backplane SPB-xxCTR

CompactPCI-6U Backplane SPB-xxCTR

CompactPCI-6U backplane (computer telephony compliant, hot-swappable type)

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 12 layers) ◆Connector: IEC1076 (2mm Hard Metric) ◆Power Supply Method: Screw Terminal (18A per terminal) +5V, +3.3V, V (I/O), +12V, -12V, GND, FG Telecom Power (-Vbat/-SELVbat) Telecom Ringing Voltage (VRG) ◆Check Terminals: PRST, DEG, FAL ◆Signal Line Impedance: 65Ω (±10%) <Features> ◆System slot is arranged on the light side (right system) ◆System slots P3/P4/P5 can accommodate rear I/O modules (IEEE1101.11) ◆Peripheral slot P3 can be used as user I/O ◆V (I/O) power switching bus bar is standard equipped (default is +5V) ◆+5V and CT coding key are standard equipped ◆Signal line termination is standard equipped (for 8-slot products) ◆Various jumper post arrangements for settings ◆Optional additional power supply terminals can be installed (Faston terminals) ◆GND - Earth (FG) connection is possible ◆Optional implementation of "Type AB" shroud is available

  • Communications

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
CompactPCI-6U Backplane SPB-08PSR

CompactPCI-6U Backplane SPB-08PSR

CompactPCI-6U backplane (compatible with PICMG2.16 R1.0 type)

**Packet Switching Backplane** <Specifications> ◆ Board Material: Epoxy Glass (FR-4, 3.2t, 10-layer board) ◆ Connector: IEC1076 (2mm Hard Metric) ◆ Power Supply Method: Screw Terminal, ATX Power Connector ◆ Check Terminals: PRST, DEG, FAL, IPMB <Features> ◆ Complies with PICMG2.16R1.0, PICMG2.0R3.0, and PICMG2.1R2.0 (Hot Swap) standards. ◆ Compatible connectors for PICMG2.9R1.0 (SMBus) available (optional). ◆ Supports 2 Fabric Slots (Slot Numbers 1, 2) Supports 6 Node Slots. ◆ System Slot (Slot Number 8) can be used as a Node Slot. ◆ RP3 and RP5 come standard with Type AB Shroud. ◆ V (I/O) voltage can be switched between 5V and 3.3V. ◆ Custom development and manufacturing available, including types that support high-frequency characteristics (low dielectric constant).

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Auto Digi Chain VME-J1 Backplane (Basic)

Auto Digi Chain VME-J1 Backplane (Basic)

16/32-bit VME bus backplane designed based on IEEE standard P1014.

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 4-layer board) ◆Connector: DIN41612 standard product ◆Terminator: 330Ω pull-up / 470Ω pull-down split termination ◆Power Supply Method: Screw terminal (standard, 1 terminal 20A) *Options (Faston terminal, 1 terminal 10A) are also available ◆Check Terminals: System Reset, System Fail, AC Fail, +5V, GND Sensing <Features> ◆This is a 16/32-bit VME bus backplane designed based on IEEE standard P1014. ◆The jumper settings for the daisy chain function are automatically configured by adopting an auto daisy chain connector, so manual configuration is not required when inserting VME boards. *When no board is inserted... Short state *When a board is inserted... Open state ◆All signals are arranged with GND patterns, minimizing crosstalk between signals. ◆+5V and GND are provided as full surface patterns in the inner layers, ensuring power stability. ◆The adoption of a multilayer board (4 layers) results in a stable impedance design.

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
VME-J1 Backplane (Basic Type)

VME-J1 Backplane (Basic Type)

16/32-bit VME bus backplane designed based on IEEE standard P1014.

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 4-layer board) ◆Connector: DIN41612 standard product ◆Terminator: 330Ω pull-up / 470Ω pull-down split termination ◆Power Supply Method: Screw terminal (standard, 1 terminal 20A) *Options (Faston terminal, 1 terminal 10A) are also available ◆Check Terminals: System Reset, System Fail, AC Fail, +5V, GND Sensing *Short plug for DigiChain configuration is optional <Features> ◆This is a 16/32-bit VME bus backplane designed based on IEEE standard P1014. ◆All signals have GND patterns arranged, minimizing crosstalk between signals. ◆+5V and GND are provided as full surface patterns in the inner layers, ensuring power stability. ◆The connector is standard press-fit type, but it is designed to also accommodate soldered connectors. *If using soldered connectors, please specify at the time of order. ◆The adoption of a multilayer board (4 layers) results in a stable impedance design.

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Auto-Digi-Chain Monolithic VME Backplane

Auto-Digi-Chain Monolithic VME Backplane

16/32-bit VME bus backplane designed based on IEEE standard P1014.

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 4-layer board) ◆Connector: DIN41612 standard product ◆Terminator: 330Ω pull-up / 470Ω pull-down split termination ◆Power Supply Method: Screw terminal (standard, 1 terminal 20A) Faston terminal *Options (1 terminal 10A) are also available ◆Check Terminals: System reset, AC fail, system fail, +5V, GND sensing ◆Bus Configuration: J1 VME SYSTEM Bus, J2 VME 32-bit expansion Bus ◆Transfer Rate: 60MByte/sec <Features> ◆A 16/32-bit VME bus backplane designed based on IEEE standard P1014 ◆Adopts auto-daisy-chain connectors ◆The a and c columns of the J2 side connector are independent and not connected, allowing for user-defined configurations ◆+5V and GND patterns are arranged to minimize crosstalk between signals ◆+5V and GND are provided as full surface patterns in the inner layers, ensuring power stability ◆The use of a multi-layer board (4 layers) results in a design with stable impedance

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
CPCI Serial Backplane "SPB-09SR"

CPCI Serial Backplane "SPB-09SR"

PCI Express 8 lanes x2 link, 4 lanes x6 link

While inheriting the mechanics of CompactPCI, it supports serial interfaces such as PCI Express, SATA/SAS, and USB. It is a strong candidate for the next-generation open bus/fabric architecture that can also accommodate hybrid systems with CompactPCI and CompactPCI Express. 【Features】 ○ Compliant with PICMG CPCI-S.0 R1.0 ○ PCI Express 8 lanes x 2 links, 4 lanes x 6 links ○ Supports various interfaces For more details, please contact us or download the catalog.

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Wooden board BA-6021

Wooden board BA-6021

Japan Basketball Association Certified Product BA-6021 Special Wooden Board for General Basketball

Basketball Backboard Wooden Board Certified by the Japan Basketball Association BA-6021 (piece) - 1,800 × 1,050 × 30 mm - With connecting frame

  • others
  • Municipal services and business location

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
VME-J2 Backplane (Universal Type)

VME-J2 Backplane (Universal Type)

VME32-bit expansion bus compatible universal backplane

<Specifications> ◆Board Material: Epoxy Glass (FR-4, 3.2t, 4-layer board) ◆Connector: DIN41612 standard product ◆Terminator: 330Ω pull-up / 470Ω pull-down termination (only for row b) ◆Power Supply Method: Screw terminal (standard, 1 terminal 20A) *Options (Faston terminal, 1 terminal 10A) are also available <Features> ◆Connector row b is for VME 32-bit expansion bus ◆Connectors in rows a and c are wired in a bus configuration ◆Power connections to rows a and c can be shorted to the +5V and GND terminals provided at both ends of the slot, and can also be connected to pins 1 to 32 as desired. Custom buses can be easily created ◆GND patterns are placed for all signals. Crosstalk between signals is minimized ◆+5V and GND are provided as surface patterns in the inner layers, ensuring stable power supply ◆Termination for rows a and c is done via wrapping wires to the IC sockets at both ends (resistors for rows a and c are sold separately) ◆In addition to +5V and GND, terminals are provided to allow for two power supplies ◆The standard connector type is press-fit, but solder connectors can also be installed. *Please contact us if you wish to use solder connectors.

  • Embedded Board Computers

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
COPYRIGHT © 2001-2025 IPROS CORPORATION ALL RIGHTS RESERVED.