1～15 件を表示 ／ 全 18 件
You can measure current without disconnecting the 4-20mA circuit.
It is possible to measure the 4-20mA signal used in industrial instruments with a clamp without disconnecting the circuit.
With one tool, you can easily install, test, maintain, and measure solar panels and solar power systems.
The Fluke FLK-IRR1-SOL solar irradiance meter allows you to perform all four essential measurements in a single user-friendly tool when investigating, installing, maintaining, and checking the performance of solar panels and photovoltaic systems. It instantly measures the solar irradiance in watts per square meter as required by the IEC 62446-1 standard. You can place the meter directly on the panel or connect an external probe to measure temperature. Use the compass to check the orientation and the tilt function to verify the slope of the roof or panel. It can carry out all the critical measurements necessary for the installation and verification of solar power systems. Additionally, it also provides reports on the performance of solar power systems. Key Features: - Measures solar irradiance, ambient temperature, PV module temperature, array orientation, and tilt angle - Instantly measures solar irradiance in watts per square meter as required by the IEC 62446-1 standard - Equipped with a large character display and high-contrast LCD for readability even in direct sunlight - Comes with a convenient carry case with a shoulder strap
It is optimized to assist in the proper operation of commercial buildings, hospitals, and schools.
The Fluke 117 features a built-in non-contact voltage detection function that helps identify circuits with voltage applied. Additionally, the AutoV/LoZ function prevents false readings caused by ghost voltage. The Fluke 117 displays True-rms AC voltage/current readings with a resolution of 6000 counts. Minimum/maximum/average readings are shown, and frequency and capacitance are measured. The battery case cover is positioned for easy access, allowing for continued work without interruption. The Fluke 117 multimeter has been independently tested for safe use in CAT III 600V environments. *For more details, please refer to the external link or feel free to contact us.*
As a standard thermometer to replace mercury thermometers, which are being criticized for their impact on the human body and the environment.
The 1551A/1552A is a thermometer that sets a new "golden standard" for industrial temperature calibration. It can be used as a reference thermometer to replace mercury thermometers, which are being scrutinized for their impact on human health and the environment. Some digital thermometers can only provide accurate measurements within a narrow range of environmental temperatures, and their accuracy deteriorates when used outside that range. However, the "Stik" thermometer can provide accurate measurements in environmental temperatures from -10 ˚C to 50 ˚C. Not only is it safer and more durable than mercury thermometers, but with an accuracy of ±0.05 ˚C across the entire range, the high-precision 1551A/1552A is also ideal as a new reference thermometer.
Please select a model that suits your needs.
A handheld-type digital multimeter suitable for various applications in the electronics and industrial fields.
Consolidation of functions for measuring atmospheric pressure, air volume, and wind speed into a robust single measuring instrument.
The Fluke 922 is compatible with most pitot tubes, allowing you to input the shape and dimensions of the duct for measurements with maximum accuracy.
Compact detachable jaw AC/DC current clamp meter that meets on-site requirements.
The jaws are designed to clamp even in tight spaces, and by separating the jaws from the main body, you can check the measurements without having to adopt an awkward position.
It has become possible to place the magnetic display away from the measurement point, improving flexibility without compromising measurement accuracy.
■ Wireless technology allows the display to be placed 9 meters away from the measurement point, improving flexibility without compromising measurement accuracy. ■ The display can be easily attached and detached using a magnetic system whenever needed. ■ Using the iFlex flexible current probe expands the measurement range up to 2500 A AC. ■ CAT IV 600 V, CAT III 1000 V. ■ Integrated low-pass filter and advanced signal processing enable use in noisy electrical environments, providing stable readings. ■ Patented inrush current measurement technology captures motor starting currents while simultaneously detecting circuit protection by eliminating noise. ■ The ergonomic design fits comfortably in the hand and can be operated even while wearing protective gear. ■ The appropriate measurement range is automatically set by the wireless transmitter, eliminating the need to change switch positions during measurements. ■ 3-year warranty. ■ Soft carrying case.
A versatile and robust tool for applications with high current. True RMS 2000A clamp meter.
The Fluke-355/353 clamp meter is a trusted tool chosen by professionals for reliable measurements in high current clamp-on current measurements up to 2000 A. With specially widened jaws, it easily clamps large conductors commonly found in high current applications.
A process meter that combines a multimeter and a loop calibrator into one tool.
Main Features - 24 V loop power - Ultra-large dual display - High-performance backlight with 2 brightness settings - 1200 Ω drive capacity for current generation - HART mode setting with loop power and built-in 250 Ω resistor - Quick check of span by switching generated current between 4 mA and 20 mA using "0 %" and "100 %" buttons - Fuse easily replaceable from the outside - Infrared port for processing data with FlukeView Forms (V2.1) software
With a limited lifetime warranty, work becomes more convenient, faster, and safer!
The "Fluke 87 V" is a highly regarded industrial multimeter, from control rooms to factory floors. When productivity is at risk, using this product provides accurate and advanced troubleshooting capabilities, helping to resolve issues quickly. To accurately measure voltage and frequency in electrically noisy equipment, such as speed-adjustable motor drives, a low-pass filter function is used. The peak capture function detects intermittent problems and transients within 250 microseconds. 【Features】 ■ Provides advanced troubleshooting capabilities ■ Helps to resolve issues quickly ■ Uses peak capture function to detect intermittent problems and transients within 250 microseconds ■ Can withstand impulses over 8,000 V ■ Reduces risks associated with surges and spikes *For more details, please refer to the external link or feel free to contact us.
Digital multimeter with 8.5-digit display adopting digital RMS method for AC measurement.
The "8558A 8.5 Digit Multimeter" provides high-resolution digitization at 5 megasamples per second for system automation in laboratory and manufacturing inspection environments. By reducing test time on high-speed digital platforms, it enables improved throughput, increased production, and enhanced return on investment. The 8588A/8558A digitizes to memory in 200 nanoseconds per reading and delivers 4.5-digit data to a PC at 100,000 readings per second via USB, Ethernet, and GPIB. High-speed, high-resolution data collection provides the quantity and quality of information necessary to make timely and accurate decisions that impact system throughput and efficiency.
A true effective value multimeter chosen by expert technicians from around the world.
The Fluke 170 Series True-rms digital multimeters are chosen by professional technicians around the world for their accuracy, reliability, and ease of use. This product is an industry standard and is equipped with all the functions necessary to troubleshoot and repair a wide range of issues found in electrical and electronic devices. The Fluke 170 Series digital multimeters feature True-rms voltage and current measurements, 6000 count resolution, and manual and automatic range settings. They also allow for frequency, capacitance, resistance, continuity, and diode measurements. Additionally, the Fluke 177 and 179 models offer a higher basic accuracy of 0.09%, and a backlit digital display capable of showing an analog bar graph. The Fluke 179 also allows for temperature measurements. *For more details, please refer to the external link or feel free to contact us.*
Its compact design and ease of use make it suitable for quick verification and field service applications.
The Fluke 115 True RMS Digital Multimeter delivers excellent performance for general electrical/electronic testing requirements. Its simple operation, compact design, and ease of use make it ideal for quick verification and field service applications. The Fluke 115 displays True RMS readings of voltage/current with a resolution of 6,000 counts, tests diodes, frequency, continuity, and capacitance, and shows minimum/maximum/average readings to record signal fluctuations. The large white LED backlight is helpful for working in dimly lit environments. The battery case cover is easy to open, making battery replacement simple. The Fluke 115 multimeter has been independently tested for safe use in CAT III 600V environments. *For more details, please refer to the external link or feel free to contact us.*
It is designed for calibration and measurement laboratories that require excellent stability to perform high-precision measurements.
The 8588A is designed for calibration laboratory applications and achieves reliable and reproducible measurements with exceptional performance. The 8588A is equipped with over 12 measurement functions, including new digitized voltage, digitized current, capacitance, RF power, and external shunts for DC and AC current, allowing you to consolidate laboratory inspection costs into a single measurement device. Its outstanding analog performance is enhanced by Fluke Calibration's new high-speed system design and industry-leading direct digitization capabilities, enabling significant throughput improvements in many automated systems that require a combination of maximum speed and highest accuracy. <We have one 8.5-digit reference multimeter 8588A available for immediate delivery.> If you are considering a new product or seeking a product with higher accuracy, please take this opportunity to consider it. For inquiries, please contact jp-info@flukecal.com. <Important notes regarding purchase> ● Sales conditions: Limited to direct transactions ● Calibration date: April 10, 2022 As quantities are limited, we kindly ask for your prompt consideration.
