日本オートマチックマシン List of Products and Services

● By installing double solenoids for ascent and descent, even if one solenoid fails while in the ON state, the press will not operate as long as the other solenoid is OFF. ● With the addition of a relay unit for two-handed operation, if the left and right hand switches are not pressed within 0.5 seconds, no output signal will be sent from the relay unit, and the press will not operate.

• Plastic processing machines (cutting and rolling)
• Other processing machines

● By installing double solenoids for ascent and descent, even if one solenoid fails while in the ON state, the press will not operate as long as the other solenoid is OFF. ● By adding a relay unit for two-handed operation, if the left and right hand switches are not pressed within 0.5 seconds, no output signal will be sent from the relay unit, and the press will not operate.

• Plastic processing machines (cutting and rolling)
• Other processing machines

● By installing double solenoids for ascending and descending, even if one solenoid fails while in the ON state, the press will not operate as long as the other solenoid is in the OFF state. ● By adding a relay unit for two-handed operation, if the left and right hand switches are not pressed within 0.5 seconds, the press will not operate because no output signal is sent from the relay unit.

• Plastic processing machines (cutting and rolling)
• Other processing machines

● By installing double solenoids for ascending and descending, even if one solenoid fails while in the ON state, the press will not operate as long as the other solenoid is OFF. ● By adding a relay unit for two-handed operation, if the left and right hand switches are not pressed within 0.5 seconds, the press will not operate because there will be no output signal from the relay unit.

• Plastic processing machines (cutting and rolling)
• Other processing machines

● By installing double solenoids for ascending and descending, even if one solenoid fails while in the ON state, the press will not operate as long as the other solenoid is OFF. ● By adding a relay unit for dual-hand operation, the press will not operate if the left and right hand switches are not pressed within 0.5 seconds, as there will be no output signal from the relay unit.

• Plastic processing machines (cutting and rolling)
• Other processing machines

Compared to the standard type, the ram speed has been increased. All hydraulic press models are equipped with a built-in double-hit restart prevention circuit, and the operation using a two-hand push button switch ensures safety. Additionally, all high-speed type models come standard with mechanical stoppers, providing stable bottom dead center accuracy that could not be achieved with sensor control.

• Plastic processing machines (cutting and rolling)
• Other processing machines

Compared to the standard type, the ram speed has been increased. All hydraulic press models are equipped with a built-in double stroke restart prevention circuit, and the operation using a two-hand control push button switch ensures safety. Additionally, all high-speed type models come standard with a mechanical stopper, allowing for stable bottom dead center accuracy that could not be achieved with sensor control.

• Plastic processing machines (cutting and rolling)
• Other processing machines

Compared to the standard type, the ram speed has been increased. All hydraulic press models are equipped with a built-in double-hit restart prevention circuit, and the operation using a two-hand control push button switch ensures safety. Additionally, all high-speed type models come standard with a mechanical stopper, which allows for stable bottom dead center accuracy that could not be achieved with sensor control.

• Plastic processing machines (cutting and rolling)
• Other processing machines

Compared to the standard type, the ram speed has been increased. In addition to having a double-hit restart prevention circuit built into all hydraulic press models, the operation using a two-hand control push-button switch ensures safety. Furthermore, all high-speed models are equipped with a mechanical stopper as standard, allowing for stable bottom dead center accuracy that could not be achieved with sensor control.

• Plastic processing machines (cutting and rolling)
• Other processing machines

The J.A.M. hydraulic press is a high-performance machine developed with a focus on the user, utilizing proven mechanical press technology throughout. It demonstrates its power in operations such as drawing, bending, and stamping.

• Plastic processing machines (cutting and rolling)
• Other processing machines

The J.A.M. hydraulic press is a high-performance machine developed with a user-oriented approach, utilizing proven mechanical press technology throughout. It demonstrates its power in processes such as drawing, bending, and stamping.

• Plastic processing machines (cutting and rolling)
• Other processing machines

●Standard equipment with light-type safety device ●In the event of an emergency stop, the power source to the servo motor will be cut off by a dual system (redundancy).

• Press Dies

●Standard equipment with light-type safety device ●In case of emergency stop, the power source to the servo motor is cut off by a dual system (redundancy).

• Press Dies

The RSS300P is a post-guide type crank press. The main body of the press features our unique compact design, making it easy to layout production lines and significantly contributing to space-saving. It can achieve a maximum stroke rate of 500 SPM, which also contributes to increased productivity.

• Press Dies

● The touch panel has been changed to a color LCD screen. ● It achieves excellent functionality and cost performance as an energy-saving press that replaces hydraulic systems. ● The ram stroke length, descent speed, acceleration and deceleration speed, and bottom dead center stop time can be set arbitrarily. ● By using the profile mode, the ram stop position, descent speed, and stop time can be set at up to five locations within a single stroke.

• Press Dies

● The touch panel has been changed to a color LCD screen. ● The ram slide is supported by a sliding V guide for high precision. ● The ram stroke length, descent speed, acceleration and deceleration, and bottom dead center stop time can be set arbitrarily. ● By using the profile mode, the ram stop position, descent speed, and stop time can be set at up to five locations within a single stroke.

• Press Dies

● The high-speed compact servo press "RSP series," which was introduced in 2011, has been renewed with significantly improved safety, operability, and quietness compared to conventional mechanical presses. ● It supports high precision of molds and continuous use at high speeds, achieving high rigidity and durability through a special coating on the sliding parts. It contributes to automation and labor-saving.

• Plastic processing machines (cutting and rolling)

● The high-speed compact servo press "RSP series," which was introduced in 2011, has been renewed with significantly improved safety, operability, and quietness compared to conventional mechanical presses. ● It supports high precision of molds and continuous use at high speeds, achieving high rigidity and durability through a special coating on the sliding parts. It contributes to automation and labor-saving.

• Plastic processing machines (cutting and rolling)

● The high-speed compact servo press "RSP series," which was introduced in 2011, has been renewed with significantly improved safety, operability, and quietness compared to conventional mechanical presses. ● It supports high precision in molds and continuous use at high speeds, achieving high rigidity and durability through a special coating on the sliding parts. It contributes to automation and labor-saving.

• Plastic processing machines (cutting and rolling)

Comparison of the core wire and insulation using two laser beams for quality assessment.

• Other processing machines

Detection of defective insulation barrels, protruding core wires, shallow and deep strikes, insertion positions of scratches and waterproof seals, cuts, inversions, etc. through images.

• Other processing machines

The wire storage section is equipped with a tray folding function, making it easy to attach and detach the No. 2 side applicator.

• Other processing machines

● The twisting of the electric wire is reduced, allowing for stable supply of the wire. ● Can be used regardless of whether it is bundled wire or bobbin wire.

• Other processing machines

This is a wire reel stand specifically for bobbins, capable of accommodating up to four different sizes of bobbins with one unit.

• Other processing machines

● It can be operated independently, allowing for use with machines from other companies. ● Using a wire tray makes it easy to manage the storage of electrical wires.

• Other processing machines

Compatible model: LCP220S

• Other processing machines

● Registration for the Crimp Height Database is possible. ● Supports a 40mm stroke.

• Other processing machines

● The orientation of the waterproof seal is determined by a sensor and supplied. ● Replacement with another waterproof seal takes a short time. ● Can be installed on fully automatic and semi-automatic terminal crimping machines with waterproof seal insertion functionality.

• Other processing machines

● It is a 2-channel specification using pressure sensors, capable of simultaneous detection of both channels. ● High-accuracy judgment is possible through comprehensive evaluation based on three types: total load, pressurization waveform, and maximum pressure. ● In addition to major defects such as cut core wires, terminal drop-offs, and lack of stripping, it also detects core wire protrusions, coating bites, shallow core wire strikes, and C/H defects.

• Other processing machines

● Crimping status: The conditions such as core wire breakage, core wire protrusion, insulation biting, shallow crimping, and abnormal crimp height can be visually assessed every time through waveform analysis. ● The quality assessment of the product can also be numerically processed by a simple pressure management device, which helps to mitigate variations in judgment among operators. ● It has become possible to record the status of manual crimping operations, which was previously difficult to document as data.

• Other processing machines

When attaching the applicator to the crimping machine's one-touch base, the shank must be held up by hand while inserting the ram bolt. However, by installing this device, it is possible to maintain the attachment height during the removal of the applicator, making it easier to lift and hold during installation. (1) It is possible to work on the shank without touching it during attachment and removal from the crimping machine. (2) Prevents damage to the die due to automatic dropping of the shank. (3) Allows for easy replacement of the applicator in a compact space.

• Other processing machines

When attaching the applicator to the crimping machine's one-touch base, the shank must be held up by hand while inserting the ram bolt. However, by installing this device, it becomes possible to maintain the installation height during the removal of the applicator, making it easier to lift and hold during installation. (1) It is possible to work on the shank without touching it during installation and removal from the crimping machine. (2) Prevention of damage to the blade shape due to automatic dropping of the shank. (3) Prevention of applicator damage due to forgetting to insert the shank into the ram bolt. (4) Easy replacement of the applicator in a compact space.

• Other processing machines

■Dedicated side terminal applicator for the JACK end crimping insertion machine, primarily compatible with low-voltage related terminals, utilizing an air cylinder for the terminal feeding mechanism. ■The blades for the crimper, anvil, etc., use the same parts as the AS40 and AS42 types.

• Other processing machines

This is a dedicated applicator for splice terminals that allows for various crimp connections such as straight, branching, and blocking through combinations to connect electrical wires together.

• Other processing machines

■It is used for continuous crimping of end terminals such as those for automotive batteries. ■The terminal feed uses a cylinder.

• Other processing machines

It is used for crimping loose terminals such as automotive battery terminals.

• Other processing machines

It is used for continuous crimping of side terminals such as automotive battery terminals. The terminal feed uses a cylinder.

• Other processing machines

■Used for crimping side terminals, it can be configured for automatic or semi-automatic machines with the replacement of feed cams, etc. ■This applicator is optimal for terminals with a short lead length and narrow pitch.

• Other processing machines

● Achieves space-saving with a tabletop type ● Compatible with side feed and end feed applicators ● Allows setting and registration of strip length, depth, and crimping position before and after on the operation panel ● Can also be used as a crimping machine

• Other processing machines

●Reduced power consumption during noise and energy-saving shutdowns. ●Adjustment using a manual handle is still possible as before.

• Other processing machines

●Reduced power consumption during noise and energy-saving shutdowns. ●Adjustment using a manual handle is still possible as before.

• Other processing machines

● Equipped with the highly reliable "JACK" insertion unit on both sides, capable of harness processing as short as 40mm. ● Set production with different wire colors and varying cut lengths is also possible.

• Other processing machines
• Other assembly machines
• Crimp Terminal

● Ultra-fine wire (AWG#32), crimping at both ends (minimum 25mm) and soldering at one end (minimum 8mm) is possible. ● Maximum of 4,200 pieces per hour for crimping at both ends, and 2,570 pieces per hour for crimping at one end and soldering at one end. ● Improved cut and strip unit mechanism allows for more stable crimping processing.

• Other processing machines

● Can crimp ultra-fine wire (AWG#36) with a short length specification (minimum 20mm) ● Increased speed allows for a cycle time of 0.85 seconds per unit (4,200 units per hour) ● Improved cut and strip unit mechanism enables more stable crimping processing

• Other processing machines

● Equipped with the highly reliable "JACK" insertion unit on both sides, capable of harness processing as short as 40mm. ● Set production with different wire colors or varying cut lengths is possible. ● Waterproof seal insertion crimping and housing insertion are available (optional).

• Other processing machines