日本オートマチックマシン Product Lineup

The material is J.A.M. original stainless steel. It is a high-precision processing vise with HRC 57° full hardening treatment, excellent rust and wear resistance. ● It is a precision stainless vise with a sign bar system. ● It is suitable for grinding processes that require angle setting. ● It features a detachable handle type.

• Vice Clamps

The material is J.A.M. original stainless steel. It is a high-precision processing vise with an HRC 57° full hardening treatment, offering excellent rust and wear resistance. It can be utilized in a wide range of fields from processing to measurement. ● It is a precision vise with a structure that prevents the handle from protruding when the jaws are opened. ● The vise's moving jaw incorporates a down-hold mechanism.

• Vice Clamps

The material is J.A.M. original stainless steel. It is a high-precision processing vise with HRC 57° full hardening treatment, offering excellent rust and wear resistance. It can be utilized in a wide range of fields from processing to measurement. ● It features a detachable handle type that can be widely used for high-precision cutting, grinding, and tapping processes with NC and MC. ● The fixed jaw, base, and nut section are integrated into a frame structure (U-shaped), making it suitable for use when the vise is turned 90 degrees sideways.

• Vice Clamps

The material is J.A.M. original stainless steel. It is a high-precision processing vise with excellent rust and wear resistance due to HRC 57° full hardening treatment. It can be used in a wide range of fields from processing to measurement. ● It is a handle detachable type that can be widely used for high-precision cutting, grinding, tapping, and other processes using NC and MC.

• Vice Clamps

The material is J.A.M. original stainless steel. It is a high-precision processing vise with HRC 57° full hardening treatment, offering excellent rust and wear resistance. It can be utilized in a wide range of fields from processing to measurement. ● This is a handle detachable type that can be widely used for high-precision cutting, grinding, tapping, and other processes using NC and MC.

• Vice Clamps

The material is J.A.M. original stainless steel. It is a high-precision processing vise with excellent rust and wear resistance due to HRC 57° full hardening treatment. It can be utilized in a wide range of fields from processing to measurement. ● It is a handle detachable type that can be widely used for high-precision cutting, grinding, tapping, and other processes using NC and MC.

• Vice Clamps

The material is SKS. It is a high-precision machining vise with an HRC60° full hardening treatment that shows no aging changes. It can be used in a wide range of fields from machining to measurement. ● Auxiliary plate with sign bar method ● An auxiliary plate with a sign bar method that allows for angle setting in two orthogonal directions. ● CSP is a tapped hole type.

• Vice Clamps

The material is SKS. It is a high-precision machining vise treated with full hardening at HRC60°, ensuring no changes over time. It can be utilized in a wide range of fields from machining to measurement. ● It features a permanent magnet chuck mounted on a sign bar type auxiliary plate.

• Vice Clamps

It significantly reduces working hours and also contributes to the reduction of human errors. Any processing data can be freely defined by the user in CSV file format using the built-in software. ● Zero work-in-progress for wires and mark tubes ● Zero combination errors between wires and mark tubes ● Zero errors in the insertion direction of mark tubes ● Equipped with a Mibu Electric mark tube printer

• Other processing machines

●Compatible with angular workpieces of 135mm and round workpieces of Φ150mm.

• Vice Clamps

● Sales are in units of one. ● Please specify the L dimension in the outline drawing. ● Four clamp claws are included. 【Regarding Orders】 ■ The wire-cut bridge is made to order. ■ Please specify the L dimension (pitch dimension of the mounting tap holes on the machine side). Example) JWS767-□□□ L dimension specified ■ We also accept orders for special specifications. For more details, please contact our sales department. ■ Sales are in units of one.

• Vice Clamps

● Sales are in units of one. ● Please specify the L dimension on the outline drawing. ● Four clamp claws are included. 【Regarding Orders】 ■ Wire-cut bridges are made to order. ■ Please specify the L dimension (pitch dimension of the mounting tap holes on the machine side). Example) JWS765-□□□ 　　　　　　　 L dimension specified ■ We also accept production of special specifications. 　 For details, please contact our sales department. ■ Sales are in units of one.

• Vice Clamps

●Sales are in units of one. ●Please specify the L dimension in the outline drawing. ●Four clamp claws are included. 【Regarding Orders】 ■Wire-cut bridges are made to order. ■Please specify the L dimension (pitch dimension of the mounting tap holes on the machine side). Example) JWS764-□□□ L dimension specified ■We also accept orders for special specifications. For details, please contact our sales department. ■Sales are in units of one.

• Vice Clamps

● Sales are in units of one. ● Please specify the L dimension in the outline drawing. ● Four clamp claws are included. 【Regarding Orders】 ■ The wire-cut bridge is made to order. ■ Please specify the L dimension (pitch dimension of the mounting tap holes on the machine side). Example) JWS763-□□□ L dimension specified ■ We also accept orders for special specifications. For more details, please contact our sales department. ■ Sales are in units of one.

• Vice Clamps

● Sales are in units of one. ● Please specify the L dimension on the outline drawing. ● Four clamp claws are included with each unit. 【Regarding Orders】 ■ The wire-cut bridge is made to order. ■ Please specify the L dimension (pitch dimension of the mounting tap holes on the machine side). Example) JWS762-□□□ L dimension specified ■ We also accept orders for special specifications. For more details, please contact our sales department. ■ Sales are in units of one.

• Vice Clamps

● Sales are in units of one. ● Please specify the L dimension in the outline drawing. ● Four clamp claws are included. 【Regarding Orders】 ■ The wire-cut bridge is made to order. ■ Please specify the L dimension (pitch dimension of the machine mounting tap holes). 　　Example: JWS761－□□□ 　　　　　　　　　　 L dimension specification ■ We also accept production of special specifications. 　 For more details, please contact our sales department. ■ Sales are in units of one.

• Vice Clamps

Tightening force increased by 1.6 times Positioning accuracy improved Body rigidity increased No protrusion of the handle Uses JAM's original stainless steel with excellent corrosion resistance By replacing the nozzle, it can accommodate various workpieces. The raw nozzle plate is unheat-treated, allowing for processing tailored to the workpiece shape.

• Vice Clamps

● Mini board pin ● Strain relief terminal ● PC pin

• Other Connectors

●Implementation height: 2.1mm. ●Front flip type that makes FPC installation easy. ●By adding a notch to the FPC, it prevents misalignment and detachment of the FPC installation position.

• Board to FPC connector

The system is modularized, allowing for flexible configuration changes according to user specifications and production conditions. ● One crimping machine supports 10 types of loose terminals ● Excellent cost performance ● Supports up to 36 types of wires ● Dies are planned to be Nichifu certified products

• Other processing machines

●Implementation height of 2.1mm. ●Front flip type that makes FPC mounting easy. ●By adding a notch to the FPC, it prevents misalignment and disconnection of the FPC mounting position.

• Board to FPC connector

●Implementation height of 2.1mm. ●Front flip type that makes FPC installation easy. ●By adding notches to the FPC, it prevents misalignment and disconnection of the FPC installation position.

• Board to FPC connector

● By using the pressure management device, you can know the actual pressure during processing. ● The display unit allows you to set any upper and lower limit values. ● It is possible to determine pass or fail against the set values.

• Plastic processing machines (cutting and rolling)

● Since it uses a light-emitting diode and pulse modulation method, as well as a pulse amplification cycle adjustment method, it is not affected by external light interference. ● When light shielding is applied during the descent of the ram, it will stop at that position. ● It uses products that are certified for type testing.

• Plastic processing machines (cutting and rolling)

● You can increase the open height. ● This is used when the open height is insufficient due to mold dimensions or workpiece dimensions. Note) In the case of a C-type frame, please be aware that increasing the height will result in a larger opening. Note) We recommend mounting with a free shank.

• Plastic processing machines (cutting and rolling)

By using an optional valve, you can change the pressure range and speed of the press's basic specifications.

• Plastic processing machines (cutting and rolling)

Prepare urethane, pearlescent, and diamond electroplated rollers according to the type and use of the electric wire.

• Other processing machines

Prevents damage to electric wires and marks caused by rollers.

• Other processing machines

I will untangle the wire using the up and down strokes.

• Other processing machines

Do not cut the terminal carrier; pass the pipe through to the outside. The terminal carrier will not scatter inside the applicator.

• Other processing machines

You can distinguish between driving, stopping, and malfunctioning stops from a distance.

• Other processing machines

● Equipped with a terminal drooping function to reduce terminal supply load. ● Detects the presence or absence of terminals and overload in terminal supply. ● Terminal overload also triggers the terminal drooping function.

• Other processing machines

By detecting wires with seams, we prevent contamination with good products.

• Other processing machines

The traditional pin-based seal pickup supply method has been replaced with a direct supply method using air transport, achieving compactness.

• Other processing machines

● Can be equipped with a belt feeder with minimal cover damage (optional) ● Two-wire selector and manual application exchange device that shortens setup time (optional) ● PC compatibility that improves connection and operability with higher production systems ● Chopper for cutting defective wire ends (optional)

• Other processing machines

● One-end crimping and one-end soldering capability: 1.1 seconds per unit (3,270 units per hour) ● Equipped with a new soldering unit, enabling smooth setup changes and reducing the burden on operators ● Standard equipped with a 2.5-ton equivalent integrated crimping machine ● Crimping shape appearance inspection using a crimp camera (optional: one side)

• Other processing machines

- By providing a discharge tray for double-end crimping, production is possible at speeds equivalent to dedicated double-end crimping machines: Double-end crimping: 0.80 seconds per unit (4,500 units/hour) Single-end crimping and single-end soldering: 1.20 seconds per unit (3,000 units/hour) - Adopts a popular structure that inserts solder along the wire axis (proven structure with CPR-ZERO-H) - Equipped with a 10-inch panel, improving visibility of the operation screen - The smallest installation space ever for CH machines - It is also possible to switch from touch panel operation to PC operation (optional) - Waterproof unit can be mounted with one touch (optional) - Crimp shape appearance inspection using a crimp camera (optional)

• Other machine tools

The connector includes multiple functions such as 10 Gbps, Alt mode, and PD functionality. *It is not compatible with USB 2.0/3.0 A/B/micro B. In the future, it will be possible to connect many devices using a single USB C cable instead of the several types of cables currently needed.

• Automotive Connectors

This new interface can transmit high-speed data of up to 15GHz (20Gbps) with robust automotive-grade connectivity. The system's high-performance modular design enhances flexibility for delivering next-generation devices.

• Automotive Connectors

VDS (Low Voltage Differential Signaling) / MHL / Flexray / USB2.0 / USB3.0 / IEEE1394 / Ethernet / APIX / CAN enable excellent data transfer. The optimized impedance connector system prevents external interference and crosstalk, providing top-class quality. The main product feature, S.S.R. (Smart Strain Relief), is an intelligent strain relief unit that allows for freedom from soldering points and prevents contamination in circuit board connections.

• Automotive Connectors

This is a connector that has achieved miniaturization and even higher transmission performance compared to previous FAKRA connectors.

• Automotive Connectors

These are based on the SMB connector interface and comply with the standards of the unified connector system established by FAKRA (Automotive Expert Group). The specially standardized locking system ensures that FAKRA connectors meet the high functionality and safety requirements of today's automotive industry. This coaxial connector conforms to the specifications of USCAR-18 and ISO 20860-1.

• Automotive Connectors

● Crimping time at both ends: 0.70 seconds per unit (5,142 units per hour) ● Compatible with a wide range of wire sizes (AWG #32 to #14) * Waterproof compatible (AWG #24 to #14) ● Equipped with a 10-inch panel for improved visibility of the operation screen ● Space-saving design achieved by placing the pre-feeder next to the main unit, reducing the operator's workload ● Option to switch from touch panel operation to PC operation ● One-touch installation of soldering and waterproof units available (optional) ● Crimping shape appearance inspection using a crimp camera (optional)

• Other processing machines

● Crimping at both ends: 0.70 seconds per unit (wire length 100mm, 5,142 units per hour) ● Standard equipped with a belt feeder that minimizes coating damage ● Standard equipped with a high-performance servo crimping machine (equivalent to 2.5 tons) Stroke changeable between 30/40mm

• Other processing machines

This is a socket screw for fixing clamp claws.

• Vice Clamps