Drone Inspection: Inspections other than statutory inspections are also possible! What is drone inspection?

Why not switch from traditional exterior wall inspections to drone inspections?

Drone inspections have been legally recognized as having the same level of accuracy as sounding rod surveys due to the amendment of Article 12 of the Building Standards Act on April 1, 2022. In traditional inspection methods, workers conducted inspections using sounding rods or took images of the exterior walls from the ground using infrared cameras, followed by image analysis. However, these methods resulted in long inspection periods and made it impossible to inspect high-rise areas. With drone inspections, it is possible to inspect high-rise areas using drones equipped with infrared cameras. Additionally, by converting inspection points into thermographic images and identifying anomalies through temperature differences, defects in high or narrow areas that were previously unobservable by human effort can now be detected. *For more detailed information or specific case studies, please feel free to contact us.*

• Contract Inspection

Would you like to switch from traditional probing rod surveys to drone inspections?

The inspection mandated by Article 12 is required for owners and managers of specific buildings as defined by government ordinances and designated administrative agencies. Drone inspections were legally recognized with the amendment to Article 12 of the Building Standards Act on April 1, 2022. In traditional inspections using tapping rods, workers had to set up scaffolding to inspect the exterior walls with tapping rods, which incurred costs and extended inspection periods, as well as posed a risk of falling accidents. However, exterior wall inspections using drones do not require scaffolding or other equipment, as they utilize drones equipped with infrared cameras to inspect the walls, allowing for cost reductions and shorter inspection periods. Additionally, since workers operate the drones from the ground, concerns about falling accidents are eliminated. *If you would like to know more details or specific examples, please feel free to contact us.*

• Contract Inspection

Would you like to switch from traditional probing rod surveys to drone inspections?

Drone inspections have been legally recognized as having the same level of accuracy as sounding rod inspections due to the amendment of Article 12 of the Building Standards Act on April 1, 2022. In traditional inspection methods, workers conducted inspections using sounding rods or took images of the exterior walls from the ground using infrared cameras, followed by image analysis for inspection. However, these methods resulted in prolonged investigation periods and made it impossible to inspect higher areas. With drone inspections, it is possible to inspect high areas using drones equipped with infrared cameras. Additionally, by converting inspection points into thermographic images to identify anomalies based on temperature differences, defects in high or narrow areas that were previously unobservable by human efforts can now be discovered. (Features) - Sounding rod inspection → Workers need to set up scaffolding for inspections, incurring labor and equipment costs. - Drone inspection → Inspections are conducted using drones, eliminating the need for scaffolding and reducing labor and equipment costs.

• Contract Inspection

Why not switch from traditional probing rod surveys to drone inspections?

Drone inspections have been legally recognized as having the same level of accuracy as sounding rod inspections due to the amendment of Article 12 of the Building Standards Act effective April 1, 2022. Traditionally, inspections were conducted by workers using sounding rods or by photographing exterior walls with infrared cameras from the ground and analyzing the images. However, these methods resulted in long inspection periods and made it impossible to inspect high-rise areas. With drone inspections, it is possible to inspect high-rise areas using drones equipped with infrared cameras. Additionally, by converting inspection points into thermographic images, it has become possible to identify abnormal areas based on temperature differences, allowing for the detection of defects in high or narrow spaces that were previously unobservable by human effort. (Features) - Capable of inspecting high-rise areas - Able to inspect without overlooking defects - No scaffolding or other equipment required - Inspections can be completed in a short period - Reduction of fall accidents - Cost savings For more detailed information or specific case studies, please feel free to contact us.

• Contract Inspection

Would you like to switch from traditional probing rod surveys to drone inspections?

Drone inspections were legally recognized on April 1, 2022, following the amendment of Article 12 of the Building Standards Act. The inspection method involves using a drone equipped with an infrared device to take aerial shots of the inspection target, measuring temperature differences on the tile surface with the infrared device to detect any lifted areas. Traditional inspections require two types of methods: tapping surveys and infrared surveys, both of which involve workers inspecting the exterior walls, making them time-consuming and costly. However, with drone inspections, the inspection is conducted by capturing aerial images of the target with a drone, eliminating the need for scaffolding and other equipment compared to traditional methods, thus reducing costs and time. (Features) - No need for scaffolding or other equipment - Cost reduction - Inspections can be completed in a short period *If you would like to know more details or specific examples, please feel free to contact us.

• Contract Inspection

If you have the address and elevation drawing of the property to be inspected, we can provide a quote! The cost can also be reduced by about half.

Miyaso Chemical Co., Ltd. conducts statutory inspections under Article 12 of the Building Standards Act using drones. Traditionally, inspections required scaffolding and the use of tapping rods, resulting in long inspection periods and high costs. However, inspections using drones significantly shorten the inspection period and reduce costs to about half. If it is difficult to conduct inspections solely with drones due to the proximity of neighboring buildings, we can propose inspections that combine traditional methods. We can provide estimates if we have the address and elevation drawings of the property to be inspected. Please feel free to consult us when needed. 【Features】 ■ Short inspection periods and costs reduced to about half ■ Ability to propose inspections that combine traditional methods ■ Estimates available with the address and elevation drawings of the property to be inspected *For more details, please refer to the PDF materials or feel free to contact us.

• Contract Inspection

Happy New Year. Thank you very much for your exceptional support over the past year. This year, we will continue to strive to provide prompt and high-quality services, and all of our employees will work hard towards this goal. We kindly ask for your continued support and patronage. We look forward to your continued cooperation this year as well.

We would like to inform you that the company name has been changed as of January 1, 2026. New company name: KELLER Pressure Co., Ltd. (Former company name: KELLER Pressure Japan Co., Ltd.) There are no changes to the phone numbers or inquiry email. Phone numbers: 03-5944-9199, 03-5944-9198 Inquiry email: sales.jp@keller-pressure.com We appreciate your continued support.

Happy New Year! Thank you very much for your exceptional support over the past year. Yoshikawa Co., Ltd.'s Realization Division will continue to contribute to solving your challenges this year as a "Realization House" that transforms your thoughts of "I want to do this" and "Is it possible to do something like this?" into reality, utilizing our skilled stainless steel processing technology. We are pleased to announce that we will be exhibiting for the first time at "The 40th NEPCON Japan," which will be held at Tokyo Big Sight from **January 21 (Wednesday) to 23 (Friday), 2026**, to introduce our technologies and products in greater depth. At our booth, we will showcase a variety of slide-type metal mask dedicated shelves that contribute to improving productivity in the electronics field. These not only lead to efficient management and improved workability in limited spaces but can also be customized according to your needs. We invite you to visit our booth at Tokyo Big Sight during this opportunity. We welcome inquiries such as "Can this processing be done?" and look forward to seeing you there.

Insulating oil from old electrical equipment that has been in use for over 30 years may be contaminated with PCBs. Proper disposal is required by the disposal deadline. If you are using a vacuum tube oscillator, please check! - Transformers - Capacitors - Rectifiers, etc. If you have oscillators or hardening equipment, please consider updating them as soon as possible. *For more details, please refer to the PDF document or feel free to contact us. ★ For inquiries by phone, please call: Osaka Headquarters → TEL: 072-991-1361 Nagoya → TEL: 052-322-1361 Tokyo → TEL: 03-5472-1361 ★ For inquiries by email, please contact: info@fujidenshi.co.jp *When calling or emailing, please mention "Ipros" as your reference. Business hours: Monday to Friday, 9 AM to 5 PM.

From March 24 (Tuesday) to March 27 (Friday), 2026, RheaVita will exhibit as a conference sponsor at ISLFD, held in Fukuoka, in collaboration with Lifix Analytical. ISLFD is an international conference where researchers and engineers involved in freeze-drying and related technologies gather from around the world to exchange information and discuss research results and technological trends. Through our sponsorship at this conference, RheaVita will present the latest information on spin freeze-drying technology. At our booth, in addition to introducing the latest information about spin freeze-dryers, we will be open to consultations on a wide range of topics, including research and development, feasibility testing, scaling up, and comparisons with existing processes. We aim to create a valuable platform for information exchange for those asking questions such as "What is spin freeze-drying?", "What are the differences from conventional freeze-drying processes?", "What are the challenges of scaling up and reproducibility?", and "What new formulation and manufacturing approaches should be considered?". Additionally, individual meetings will be possible during the conference. If you contact us in advance, we will secure a meeting opportunity at a time that is convenient for you. Please be sure to stop by the RheaVita booth.