Use case: Video with F2 air nozzle set with photoelectric sensor.

A slim ionizer that can be installed in gaps and narrow spaces where general ionizers are difficult to set up! It emits high-concentration ions uniformly with a close installation of 3 to 10 mm.

The "Ion Blade F2 Series" is a flat, thin electrostatic eliminator that can be installed in narrow spaces where conventional needle-type electrode ionizers are difficult to set up. It enables efficient static elimination without wind and with uniformity from a proximity distance of 3 to 10 mm. It can be used for static elimination between rollers inside printers and copiers, installed on air conditioner louvers, and for indoor static elimination and air purification during the dry winter months. Conventional ionizers with needle-type electrodes have a gap between the electrodes, which can create areas where ions are hitting directly beneath the needle electrodes and areas where they are not when installed closely, necessitating ion irradiation from a distance. Our ionizer has densely formed ion generation points, allowing for high-concentration ions to be generated across the entire element, making close installation possible. 【Features】 - Ion generation method: Linear Interval AC method - Thickness of 1.6 mm, suitable for gaps and narrow spaces - Selectable from three effective static elimination lengths and two types of blade modules - Static elimination at a distance is also possible by directing air at the discharge blade *For more details, please refer to the PDF document or feel free to contact us.

• Static electricity eliminator

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.