PSE certified! The "ENC-360" stationary battery charger suitable for AGVs and robots features three-stage charging to extend battery life and achieve full charge in a short time!

The charger applicable to lead-acid batteries and lithium-ion batteries can be programmed according to the battery used. Operating temperature range: -30°C to +70°C.

The "ENC Series" battery charger is a desktop type battery charger that adopts a three-stage charging method. It is suitable for lead-acid batteries (non-sealed, sealed, gel, AGM) and lithium-ion batteries (lithium iron phosphate, ternary lithium-ion, etc.), and the program settings can be adjusted according to the type of battery used. Additionally, it has built-in protection circuit functions, ensuring safe and secure usage. 【Features】 - Suitable for charging lead-acid and lithium-ion batteries - Adopts a three-stage charging method - Can be used in various countries with a wide input voltage range - Programmable charging method (optional item: SBP-001) - Remote ON/OFF control and built-in temperature sensor - Charging voltage can be set according to the type of battery - Over-voltage protection, over-temperature protection, short-circuit protection, overload protection, battery reverse connection protection - Maximum efficiency: 90.5% *For more details, please refer to the PDF document or feel free to contact us.

• Charger

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.