★Introduction of New Products★ Specially Modified HEC, Silicone-Free Wetting Agent, Zero VOC Neutralizer

Introducing a hydrocarbon-based wetting agent with superior leveling properties compared to silicone, featuring an ideal balance of low foaming and low dynamic surface tension!

EASY-WET is a new product from Ashland, a U.S. company, and is a hydrocarbon-based wetting agent (surfactant) that can be used for various industrial coating applications such as wood, metal, automotive, industrial finishes, printing inks, and plastic coatings. <Main Features> - Excellent Wetting (Leveling) Compared to conventional hydrocarbon-based wetting agents or silicone-based wetting agents, it quickly reduces the contact angle and achieves equal or better performance. It enables the application of a smooth coating film on substrates, forming a uniform coating even on the edges of the substrate. - Low Foaming and Formation of Coating Films with Few Craters In continuous stirring tests, it has been confirmed to foam less than conventional hydrocarbon, silicone, and fluorine-based wetting agents, allowing for the formation of coating films with fewer craters. - Biodegradable, Low VOC The basic structure is composed of hydrocarbons, resulting in low environmental impact and biodegradability. Additionally, its low VOC content contributes to the reduction of carbon dioxide emissions. For more details on each product, please refer to the product pages below or feel free to contact us.

• Chemicals
• Coating Agent
• paint

Introducing a variety of resin emulsions and environmentally friendly pH adjusters that are VOC (volatile organic compounds) free and can be used in water-based paints and coatings!

pHLEX ZERO is a VOC-free, low-odor, non-organic amine neutralizer that can be used in industrial applications such as paints, coatings, and resin emulsions. It is a product that serves as an alternative to pH adjusters like ammonium and organic amines. <Product Advantages> - VOC-free - Low odor - Low viscosity - Non-yellowing - Long-term neutralization stability <Chemical Substance Registration> Registered in various national inventories including TSCA (USA), EINECS (Europe), DSL (Canada), AICS (Australia), KECL (South Korea), PICCS (Philippines), China, and Japan. For more details on each product, please refer to the product pages below or feel free to contact us.

• Chemicals
• Coating Agent
• paint

New cellulose-based thickener product NATROSOL F-2000! Introduction in Japan has begun! It can reduce costs for water-based paints and improve the appearance and durability of coatings.

NATROSOL F-2000 is a cellulose-based water-soluble thickener newly developed by Ashland, capable of enhancing the performance of conventional HEC. It has a strong track record, particularly in decorative coatings resembling sand or earthen walls overseas. ◎ High Thickening Efficiency Compared to conventional high-viscosity HEC, it can reduce the required amount by approximately 43%, which is expected to lower coating costs. ◎ Excellent Water Resistance It has been confirmed to have superior water resistance in immersion tests compared to conventional HEC, preventing whitening of the coating film. ◎ Color Stability It exhibits excellent color stability and high saturation. In decorative coatings resembling sand walls, it presents a natural coloration close to the original colors of stones and sand. For more details on each product, please refer to the respective product pages and PDF catalog below, or feel free to contact us.

• Chemicals
• Coating Agent
• paint

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.