We will participate in the "New Technology Creation Exchange Meeting 2024 Product Exhibition" (October 25-26, Tokyo Tama Future Messe).

Bulk, thin film, micro areas, plate-shaped, sheet-shaped, almost all materials can be accommodated. Please consult us once.

Supports various thermal conductivity measurement methods such as steady-state method, periodic heating method, and thermoreflectance method. Compatible with plate-shaped, sheet-shaped, soft samples, fibrous materials, and various shapes. Please consult us even for samples that have been rejected by other companies.

• Contract measurement

Introducing devices for measuring the thermal diffusivity of sheet-like and plate-like materials, as well as thermal evaluation devices for fiber orientation distribution!

Introducing Bethel's thermal property measurement devices. The "Thermo Wave Analyzer TA33/35" is a measurement device for the thermal diffusivity of sheet and plate materials, capable of measuring the thermal diffusivity of functional materials. The "Thermal Microscope TM" has been commercialized through joint development with the National Institute of Advanced Industrial Science and Technology's Measurement Standards Division, allowing for measurements in micro-regions and thin films. Additionally, we offer the "Thermal Imaging Scope TSI," which visualizes thermal conduction paths using infrared cameras and lasers, as well as the "Fiber Orientation Evaluation System TEFOD." 【Features of the Thermo Wave Analyzer TA33/35】 ■ High freedom of sample shape ■ Dynamic range from organic films to diamonds ■ Anisotropy evaluation through measurements in horizontal and vertical directions ■ Evaluation of defects and irregularities through distribution measurements *For more details, please refer to the PDF document or feel free to contact us.

• Other measurement, recording and measuring instruments

Understanding the mechanism of heat transfer and effectively dissipating heat is important! Here we introduce various methods for measuring thermal properties.

Due to factors such as "miniaturization = fanless design" and "widespread use of power devices = increased heat generation," thermal issues have become important. Thermal conductivity measurement can be broadly classified into two categories: "steady-state method" and "transient method." The steady-state method provides direct thermal conductivity values and requires relatively large samples. The transient method can measure thermal diffusivity and thermal effusivity, and it is possible to measure with relatively small samples. We provide further detailed explanations, so please take a look at the PDF download below. 【Characteristics of the "Steady-State Method" and "Transient Method"】 ■ Steady-State Method - Direct thermal conductivity can be obtained - Requires relatively large samples ■ Transient Method - Can measure thermal diffusivity and thermal effusivity - Can measure with relatively small samples - Requires specific heat capacity and density *For more details, please refer to the PDF document or feel free to contact us.

• Other measurement, recording and measuring instruments

Non-contact measurement of thermal diffusivity using a laser. Measurement of resin-based materials is also possible.

The ThermoWave Analyzer TA measures thermal diffusivity using a non-contact method with a laser. Since the thermal conductivity of composite materials made of fillers and resins varies significantly with the mixing ratio, measuring thermal diffusivity is essential. Measurement of resin-based materials is also possible. Please contact us for more details.

• Logic Analyzer

Non-contact measurement of thermal diffusivity using a laser. Measurement of materials with high thermal conductivity is possible.

The ThermoWave Analyzer TA3 measures thermal diffusivity using a non-contact method with a laser. It is capable of measuring materials with high thermal conductivity. Measurements can be taken without worrying about the shape. For more details, please contact us.

• Logic Analyzer

To customers considering the introduction of vehicle detection sensors for parking lot construction, design, and management: Are you facing any issues with the challenges you currently have or selecting the right sensors for parking lot management? Hotron offers free materials that explain how to utilize vehicle detection sensors and the benefits of their introduction! ▽ Here is the lineup of materials ◉ Basic Guide to Vehicle Detection Sensors This guide focuses on the challenges and solutions in parking lot operations, introducing the overview of vehicle detection sensors. ◉ Key Points for Introducing Vehicle Detection Sensors This material discusses the benefits of introduction based on installation locations and specific challenges. ◉ Case Studies of Vehicle Detection Sensor Implementation This document introduces the challenges before implementation and the results after introduction. For more details, please download from our website and check it out. https://www.hotron.co.jp/download/

AlphaGemBio's filter tips have achieved excellent liquid release through improvements in resin and mold structure. They are a universal type that fits most pipettes. The high-performance ULDPE filter protects you and your pipetter. 【Product Specifications】 ■10μl filter tip ■20μl filter tip ■200μl filter tip ■275μl filter tip *For more details, please download the PDF or contact us.

The high-voltage fuse "EVFP 38x64 500V" has a proven track record of being adopted by many automobile manufacturers. It is a compact and lightweight automotive high-voltage fuse with excellent vibration resistance, and it is commonly used as a fuse for main circuit protection in high-voltage battery packs, drive motors, and charging systems for BEVs and HEVs. It is often adopted as an automotive fuse for high-voltage circuits to meet the needs of hybrid and electric vehicles. The EV fuse developed by PEC has been adopted not only by domestic manufacturers but also by automobile manufacturers worldwide, and it continues to be improved, becoming the global standard for fuses.

The pinhole inspection for packaging engineering is fully automated, eliminating packaging defects based on certain quality standards. The judgment results and operational status can be managed via a monitor screen. - Quantitative management of quality standards for the pinhole inspection process - Ensuring the quality of the product's shelf life - Establishing evaluation criteria for the manufacturing process, achieving quantitative quality assurance - Slim and space-saving design that can be connected to existing production lines - Quick changeover for product variety switching can be handled in a short time by exchanging chambers - Fully domestically produced, allowing for rapid maintenance and troubleshooting - Example target works: pillow packaging, packaged rice (packaged cooked rice), etc. *Please consult us regarding the use of this product for pharmaceuticals.

Introducing a "non-destructive testing device as an alternative to the submerged test" for pharmaceutical packaging products. "Complete vial leak testing device | MSQ-2002 series" Fully automating leak tests for various vials, bottles, eye drops, and cylindrical containers. Please check the link below for videos and catalogs.