Improvement of maintenance work efficiency and enhancement of the oil booth.

Improvement of maintenance work efficiency and enhancement of the oil booth.

The maintenance inspection door for filter replacement and cleaning, designed on the back of the oil booth, which is a collection booth for overspray mist specifically for painting, has been improved from a conventional single-panel door to a two-panel door, making it lighter. This allows for easier removal during inspections, enabling more efficient maintenance work. The oil booth is a painting booth that uses oil to address various issues on-site, such as work environment, pollution, and quality, which could not be achieved with a water wash booth. It features a dust removal efficiency of 95%, a low noise design of 68 dB that allows for conversation and meetings in front of the booth, and an oil lifespan of over 30 years.

• Other environmental equipment
• Wastewater/wastewater treatment equipment

Low noise design, long lifespan. Spray booth using oil in the cleaning solution.

● A painting booth that uses a special oil in the cleaning solution. ● The oil catches overspray mist. ● With a low noise design of 68db, conversations can be held even in front of the booth. It allows for painting that takes into consideration the surrounding environment. ● By connecting a sludge recovery device (optional), sludge can be semi-automatically processed and solidified through a centrifugal separation method, significantly reducing industrial waste costs.

• Painting Machine
• Other painting machines
• Other dust collectors and related products

Low noise design, long-lasting paint booth.

Economical mist inhalation booth using oil

• Other industrial robots
• Dust collector

Standard equipment with LED lighting

The explosion-proof fluorescent lights have been replaced with LED lighting. ● Brighter than explosion-proof fluorescent lights! LED lighting achieves the same brightness with significantly lower power consumption compared to explosion-proof fluorescent lights. ● More faithful color representation of paints! LED lighting reproduces colors similar to natural light, allowing for a more accurate display of paint colors. ● Reduced power consumption and energy-saving! Compared to fluorescent lights with a power consumption of about 40W, LED lighting consumes approximately 14.7 to 25W, resulting in about half the power-saving effect.

• Other painting machines

The insulating oil of old electrical equipment that has been in use for over 30 years may be contaminated with PCBs. Proper disposal is required by the disposal deadline. If you are using a vacuum tube oscillator, please check! - Transformers - Capacitors - Rectifiers, etc. Please consider updating any relevant equipment such as oscillators and hardening equipment as soon as possible. *For more details, please refer to the PDF document or feel free to contact us. ★ For inquiries by phone, please call: Osaka Headquarters → TEL: 072-991-1361 Nagoya → TEL: 052-322-1361 Tokyo → TEL: 03-5472-1361 ★ For inquiries by email, please contact: info@fujidenshi.co.jp *When calling or emailing, please mention "I saw it on Ipros." Response hours: Monday to Friday, 9 AM to 5 PM.

We will introduce the implementation results of the sensor technology developed by the Hotron Group, which has been cultivated over more than half a century, through customer case studies. In addition to automatic door sensors, we also offer a wide range of vehicle detection sensors and nursing/care sensors. Many implementation examples are also presented, so please take a look at the case study page.

In battery manufacturing lines, if components containing copper are used, there is a possibility that metal powder may mix in, dissolve, ionize, and pass through the separator, causing a malfunction that connects the positive and negative electrodes. Such minute metal powders may not be detected during pre-shipment inspections, and even if they are found, they can lead to various issues, such as the need to increase inspection processes to detect them. Therefore, Fukuda has developed a copper-free (all stainless steel) air leak tester that can be safely used in the production lines of battery manufacturers and secondary battery manufacturing equipment manufacturers. For product specifications and details, please refer to the "Related Product Information" and "Related Catalogs" below.

Fukuda's new flagship model. - Masterless type (FLA-0200 series) - General type (FLA-0201 series) Two models of air leak testers. With the mastering correction function, high-precision measurements can be achieved in a short time. Please take a look at the catalog.

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!