[Virus and Infectious Disease Measures] Face recognition speed of 0.2 seconds or less, face recognition accuracy of over 99%! Staff can call the elevator in nursing homes and care facilities using face recognition.

Deep learning high-speed facial recognition! Facial recognition speed under 0.2 seconds, facial recognition accuracy over 99%!

The "DS Series" is a high-speed facial recognition device that achieves faster facial recognition with high accuracy. Facial recognition speed is under 0.2 seconds, with an accuracy of over 99%! It can be used in various locations such as medical facilities, public facilities, environmental facilities, educational institutions, and office buildings, reducing the risk of virus and bacteria transmission as an entry and exit system. You can choose from three types according to your location and application. ■ Product Lineup 【Facial Recognition Terminal DS342】 - High-speed facial recognition with deep learning - Compact smartphone size - Supports mask recognition 【Facial Recognition Terminal (Felica compatible) DS372F】 - High-speed facial recognition with deep learning! Equipped with a Felica card reader - 7-inch tablet size ◎ For more details, please download the catalog or contact us.

• Surveillance Cameras
• Other safety equipment
• Entrance and exit control system

The "DS Series," which installs facial recognition devices in nursing homes and care facilities with dementia patients, allowing only registered staff to call the elevator.

The Hotron automatic door sensor can be used not only for automatic doors but also for opening and closing elevators and calling them. We will address various concerns and challenges you may have. 【Challenge】 We want only staff to be able to call the elevator in facilities for dementia patients. 【Solution】 Install a facial recognition device so that only registered individuals can call the elevator. ◎ Please feel free to contact us.

• Surveillance Cameras
• Other safety equipment
• Entrance and exit control system

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.