We have opened the WEB exhibition booth.

Demonstrating power in various fields from powders to liquids! High-precision level measurement with a unique algorithm.

We would like to introduce our "Ultrasonic Level Meter" that we handle. We offer the "KDH1200," which achieves stable level measurement with DSP technology, and the low-cost model "KDH353-A," which features an integrated sensor and control unit. Please use them according to your application. 【KHD1200 Features】 ■ Eliminates the influence of noise and unwanted reflections, enabling stable measurements ■ Can connect two sensors to one controller ■ Standard equipped with flow meter function ■ Logs recorded on microSD ■ Standard equipped with RS-485 (MODBUS) *For more details, please refer to the PDF document or feel free to contact us.

• Other measurement, recording and measuring instruments

No wiring required for long-distance signal communication! An explanation of multi-hop wireless in manga format.

This booklet provides an easy-to-understand explanation of the multi-hop wireless system "Kunimaru" through manga. We respond to the real voices from manufacturing sites, such as "We want to introduce a level meter and manage it all at once, but the tanks are far away, so wiring work is necessary." Please feel free to download and take a look. 【Contents】 ■ Multi-hop wireless "Kunimaru" ・ Wireless * For more details, please refer to the PDF document or feel free to contact us.

• Communications
• Wireless LAN
• Other network tools

Over 1,000 types of electrode shapes and special circuits are available for various applications! Leave difficult applications to us!!

Custom-Made Delivery Record No. 1 1. High-sensitivity electrodes can be used for materials with low dielectric constant. 2. Coated electrodes can be used for corrosive materials. 3. Automatic correction function is standard, allowing for use with viscous materials like honey. 4. Flat electrodes can be used when there are concerns about load detection at lower limits or when stirring prevents the electrodes from being placed inside the tank. 5. Wire electrodes can be used for measuring the angle of repose. 6. Pipeline electrodes can be used for flow detection within pipes. 7. Heat-resistant electrodes can be used in locations with temperature. 8. For use in areas with vibrations from knockers or vibrators, amplifier-separated types can be used. 9. If installation space is limited, amplifier-separated cable direct output specifications can be accommodated. 10. Installation and materials can be tailored to the measurement object and your preferences. In addition to the above, we will select models suited to your usage locations. We also accommodate measurements for high-difficulty applications, so please feel free to consult with us.

• Level gauges and level switches

It is possible to measure exhaust gas flow rate and flow volume! Measurements can be taken in dust environments up to 1000 mg/m3! When combined with a dust monitor, mass flow can also be measured!

The "STACKFLOW 400" is an ultrasonic exhaust gas flow meter that enables stable measurements through a unique measurement method. The sensor probe contains two opposing transducers, with ultrasonic pulses emitted from each transducer and detected by the other transducer. It can be installed in both vertical and horizontal piping, and can measure processes with temperature and pressure changes. 【Features】 ■ Self-diagnostic function included ■ Usable in dust environments of 0-1000 mg/m3 ■ Resolution of 0.1 m/s ■ Installable in vertical and horizontal piping ■ Can measure mass flow when combined with a dust monitor *For more details, please refer to the PDF document or feel free to contact us.

• Flow Meter

Instantaneous concentration changes won't be missed! Achieving ultra-low concentration measurement, high-speed response, and free maintenance.

The "VIEW Series" is a high-resolution and highly stable dust monitor that is less affected by dust adhesion to the probe compared to conventional triboelectric methods and traditional optical detection methods. Starting with the "VIEW370," which can be used for measuring dust concentration in various processes, the lineup also includes the "VIEW Ex800," which can measure in hazardous areas. Despite having one of the largest functionalities among dust monitors, it achieves high-speed data processing. 【Features】 ■ Almost unaffected by adhesion or dirt on the probe ■ Ultra-high sensitivity of 0.01 to 1000 mg/m3 ■ PTFE and FRP coatings can be manufactured (VIEW370・370PRO) ■ Capable of measuring high-humidity gases with a special air purge (VIEW370・370PRO) ■ Free power supply: AC 90 to 260V *For more details, please refer to the PDF document or feel free to contact us.

• Other measurement, recording and measuring instruments
• Other process controls

A unique principle dust monitor that calculates the ratio of dust particles, sparkle (amount of change), and light reception to determine dust concentration.

The "Dynamic Opacity Method Dust Monitor" has no moving parts, making it highly reliable and capable of stable measurements over long periods. We offer a lineup that includes the basic model mass concentration meter "STACK602," which can measure exhaust ducts up to 15m, the basic model relative concentration meter "VIEW580," and the light transmission dust monitor "STACK710." Unlike typical light scattering dust monitors, our measurement principle is not affected by lens dirt or optical axis misalignment, simplifying maintenance. 【Features】 ■ Wide range: <10–1000mg/m3 ■ Free power supply: AC90–260V ■ Highest resolution: 0.2mg/m3, maximum response speed: high sensitivity and fast measurement at 2 seconds ■ Unique measurement principle allows for calibration-free operation despite being an optical dust monitor ■ Capable of measuring large ducts of 10m (15m for the STACK602 model) due to the use of high-brightness LEDs *For more details, please refer to the PDF document or feel free to contact us.

• Other measurement, recording and measuring instruments

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without affecting the base material with heat. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly creating sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or variations in dimensions, can be created in a single molding process. This allows for the verification of multiple types in a short period.