【Visualizing ultraviolet light from 250 to 500 nm!】 UV sensor seal / ultraviolet sensor seal 【Can be cut into any shape】

Visualizing ultraviolet light from 250nm to 500nm!!!

The UV sensor seal (ultraviolet sensor seal) is a thin, flexible sheet-type sensor. It emits visible light from the area exposed to ultraviolet radiation. It can be cut into any shape and used by peeling off the backing to stick it in various locations. The phosphor is coated with adhesive on a transparent Mylar. This sensor seal is not laminated. By adhering the sensor seal to reflective materials, it becomes a reflective-type sensor, allowing you to confirm the emission from the irradiated surface. When attached to transparent materials, it acts as a transmissive-type sensor, enabling confirmation of emission from both sides.

• Other inspection equipment and devices

Visualizing ultraviolet light from 250nm to 500nm!!!

The UV sensor card (ultraviolet sensor card) is laminated and is the most common product in the UV sensor series. It emits visible light from the areas exposed to ultraviolet radiation. The letter R (reflective) at the end of the model number indicates that the UV beam image is displayed only on the front side of the card (the irradiated side). The letter T (transmissive or translucent) at the end of the model number indicates that the UV beam image is displayed on both sides of the card. At the same ultraviolet intensity, the R-type card provides a clearer image due to the backing of reflected light. The surface is not laminated to prevent the blocking of ultraviolet rays.

• Other inspection equipment and devices

Visualization of infrared light from 700 to 1700 nm through electronic trapping!!!

The IR sensor card (infrared sensor card) is laminated and is the most common product in the IR sensor series. It emits visible light from the area where infrared is irradiated. The letter R (reflective) at the end of the model number indicates that the IR beam image is displayed only on the front side of the card (the irradiated side). The letter T (transmissive or translucent) at the end of the model number indicates that the IR beam image is displayed on both sides of the card. At the same infrared intensity, the R type card provides a clearer image due to the backing of reflected light. The phosphor layer is laminated between transparent plastics suitable for various near-infrared detection and imaging applications.

• Other inspection equipment and devices

Visualizing infrared light from 700 to 1700 nm through "electronic trapping"!!!

The IR sensor seal (infrared sensor seal) is a thin, flexible sheet-type sensor. It emits visible light from the area where infrared light is irradiated. It can be cut into any shape and used by peeling off the backing to stick it in various locations. The phosphor is coated with adhesive on transparent Mylar. This sensor seal is not laminated. By attaching the sensor seal to reflective materials, it becomes a reflective sensor, allowing confirmation of light emission from the irradiated surface. When attached to transparent materials, it acts as a transmissive sensor, enabling light emission to be confirmed from both sides.

• Other inspection equipment and devices

Visualizing infrared light from 700 to 1700 nm using "electronic trapping"!!!

The infrared position detection board is a sensor printed with crosshairs and circular sighting lines on a 3mm thick polycarbonate substrate. It emits visible light from the areas where infrared is irradiated, making it ideal for adjusting the optical axis of infrared. There are versions available in reflective (R) and transmissive (T). They can be secured to various fixtures using clamps, drilling, bolting, or other methods for installation on different equipment. Both versions have measurement lines marked in 2mm increments.

• Other inspection equipment and devices

● The production time for casting prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly creating sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or variations in dimensions, can be created in a single molding process. This allows for the verification of multiple types in a short period.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without affecting the base material with heat. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

Dear Sir/Madam, I would like to express my congratulations on the continued prosperity of your company. Thank you very much for your exceptional support. We would like to inform you that our company will be closed for winter holidays during the following period. We apologize for any inconvenience this may cause and kindly ask for your understanding. 1. Winter Holiday Period From Thursday, December 28, 2023, to Thursday, January 4, 2024. 2. Business Operations After the Winter Holiday Period We will resume normal operations from Friday, January 5, 2024.

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.