Starting tomorrow, we will be exhibiting at the Secondary Battery Expo (Tokyo Big Sight) ◇ For inquiries about slurry dispersion, Plimix will be at your service.

Regarding the particle dispersion method for slurry, we propose the solid kneading method → CDM process (patented) [related video available].

We propose a CDM process using our Filmix® as a method for manufacturing electrode slurries for lithium-ion batteries. Compared to traditional solid kneading methods, it offers the following advantages: - Short processing time - High dispersion capability - High reproducibility - Easy scale-up for mass production ■ Solid Kneading Method Process We use kneading machines such as Hibis Dispermix. The typical process involves adding all the powdered raw materials → gradually adding liquid raw materials → kneading until it forms a crumbly to dough-like consistency → further adding liquid raw materials gradually for dilution → performing viscosity adjustment and degassing. <Problems with the Solid Kneading Method> - Maximum scale is around 1,000L - Takes 5 to 10 hours per batch - Low reproducibility ■ CDM Process Steps In the CDM process, instead of taking 5 to 10 hours, we slurry the mixture by adding all liquid and powdered raw materials at once and pre-mixing for about 30 minutes until it can be pumped → then we continuously process the entire amount using Filmix® in 30 minutes. <Effects of the CDM Process> 1) MAX processing of 1,920L/H 2) High reproducibility due to fewer man-hours 3) Reduction in the number of personnel required 4) Decrease in the number of devices and installation area needed

• Emulsifier/Disperser
• Mixer/agitator
• Homogenizer

Continuous manufacturing process and equipment for electrode slurry using Filmix® developed for dispersing electrode materials of lithium-ion batteries and fuel cells.

CDM stands for Continuous Dispersion Mixing, which is a continuous manufacturing process for electrode slurries using Filmix® developed for the dispersion applications of electrode materials in lithium-ion batteries and fuel cells. The nanoparticle design mixer (dispersion stirring device) Filmix® 56-L type is compatible with both batch and continuous processes. It can also be used by setting up a continuous line on a tabletop. ▼▼ Basic Procedure for Continuous Operation ▼▼ 1) Preliminary dispersion with a homodisperse or similar device 2) Transfer of the processing liquid using a pump 3) Dispersion with Filmix® ■ This single unit can be compactly used from research and development to small-scale production! ■ There are many successful scale-up cases from research machines to production machines! ◆◇━━━━━━━━━━ 　　Testing Now Available! ━━━━━━━━━━━◇◆ If you have materials that are problematic for dispersion or homogenization, please give it a try. We are currently offering two booklets related to battery manufacturing as a gift. 　◎ 'Battery Device Countermeasures Booklet'　　 　◎ 'Booklet on Fuel Cell MEA Manufacturing' * If you would like to request a test or booklets, please feel free to contact us.

• Mixer/agitator

[Video Available] Improve the quality and reduce costs of electrode material slurry! Numerous delivery achievements in the battery industry with the slurry manufacturing equipment Filmix® *Catalog available.

Filmix® is a mixer (dispersion stirring device) that enables sharp particle size distribution and micronization to nanometer sizes, which was difficult to achieve with conventional high-speed stirrers. It has a proven track record in the battery industry. ● Uniform Mixing The performance of lithium-ion battery electrode materials cannot be realized without uniform mixing. By using Filmix® to mix materials uniformly, a highly stable slurry can be produced. ● Accelerated Development Speed By achieving emulsification, dispersion, and nanometer-level micronization in seconds with Filmix®, development time can be significantly reduced. ● Testing Now Available! If you have materials that are challenging to disperse or homogenize, please give it a try! Additionally, we are currently offering two catalogs related to electrode material slurry production as a gift! ◎ "Continuous Production Technology CDM Process (Filmix® Catalog)" ◎ "Booklet on Fuel Cell MEA Manufacturing" *If you would like to request a test or catalogs, please feel free to contact us.

• Emulsifier/Disperser
• Mixer/agitator
• Homogenizer

Improving the quality of slurry and reducing manufacturing costs! Introducing continuous production technology for electrode material slurry using Filmix® (continuous processing in the kneading process).

Using the dispersing mixing device Filmix(R), active materials, conductive materials, solvents, and binders are uniformly dispersed in a short time. A slurry with high reproducibility of viscosity and excellent stability can be continuously produced. <Components of the CDM Process> ○ Pre-mixer ◎ Filmix(R) ○ Storage tank (conditioning tank) <Advantages of the CDM Process> ■ Produces high-quality slurry! ■ Reduces manufacturing time! ■ Cost reduction! (Compact factory, labor saving) ■ Easy to scale up!

• Secondary Cells/Batteries
• Lithium-ion battery
• Mixer/agitator

The "CCS2" is a ceiling-mounted vehicle counting sensor that employs an infrared reflection method. It can detect vehicles in both directions with just one unit, accurately counting vehicles even during traffic jams or when vehicles pass each other. Additionally, this product can be used not only for vehicle counting but also as a sensor for departure warnings. Furthermore, by using a separately sold dedicated remote control, it is easy to reset the sensor alone, switch the counting direction, and change the patterns of the departure warning timer. 【Features】 ■ Angle adjustment is possible up to ±5° ■ Can be installed in locations with high ceilings up to 4m ■ Detection area consists of 40 spots, allowing for wide-range detection ■ The display LEDs are color-coded by direction, making operation confirmation easy.

Many people may have questions like, "What can be done with IoT?" and "What is needed?" upon hearing the term IoT. Through digital communication, it is possible to obtain various information such as flow sensors, valves, circuit boards, and abnormal monitoring that were not accessible with traditional analog control. For example, by monitoring the valve opening, one can detect blockages in the equipment and identify leaks from cumulative flow. This information directly contributes to reducing downtime and improving quality through continuous long-term monitoring and knowledge-based management. Compatible models include those with digital communication via RS485, in addition to traditional analog controls like 0-5VDC and 4-20mA. (Older models such as the 58xxS, MfxxS series, SLA58xxS, and SLAMfxxS series). Even older models that do not support digital communication can be upgraded to the latest mass flow models, enabling digital communication. The dimensions between new and old models are the same, and no wiring changes are necessary. Additionally, we can provide control boxes for data collection from mass flow. This enables a "visualization" of small IoT without making large changes to the equipment.

Model SLA5850/SLA5851/SLA5853/SLA5860/SLA5861/SLA5863 "With just one unit, you can use 14 types of pressure and flow rates in a single process." Imagine such a mass flow controller platform. Moreover, it features excellent reproducibility, precision, and repeatability. This is the evolved simple performance of the SLA5800 series mass flow controllers/meters. The SLA5800 series boasts high accuracy, zero point stability, and repeatability that are characteristic of Brooks Instrument, a leader in mass flow measurement and control technology. Equipped with configurable advanced multi-gas/multi-range capabilities, it offers superior zero drift specifications compared to competing products while demonstrating long-term maintenance of factory calibration and accuracy.

Model SLAMf50 / SLAMf51 / SLAMf53 / SLAMf60 / SLAMf61 / SLAMf63 / SLAMf64 "Durability to withstand harsh environments! Achieving excellent precision with precise mass flow control" Whether indoors or outdoors, in environments with dust or places that handle water, the 'SLAMf series' elastomer seal thermal mass flow controllers/meters provide proven high precision and long-term stability unique to the "SLA5800 family." Applications ■ Pilot plants for petrochemical and chemical gases ■ Life science bioreactors ■ Blanketing in food processing

We will introduce the implementation results of the sensor technology developed by the Hotron Group, which has been cultivated over more than half a century, through customer case studies. In addition to automatic door sensors, we also offer a wide range of vehicle detection sensors and nursing/care sensors. Many implementation examples are also presented, so please take a look at the case study page.