We have compiled a list of manufacturers, distributors, product information, reference prices, and rankings for Bridge prevention device.
ipros is IPROS GMS ・ IPROS One of the largest technical database sites in Japan that collects information on.

Bridge prevention device - List of Manufacturers, Suppliers, Companies and Products

Bridge prevention device Product List

16～20 item / All 20 items

Displayed results
0146 Prevention of bridge formation in casting sand chutes

0146 Prevention of bridge formation in casting sand chutes

Crack and bridge measures for hoppers! Problem-solving with a Brody disk.

We would like to introduce a case where measures against bridging in the mold sand chute were implemented. Traditionally, a vibrating bridge breaker and an electromagnetic knocker were used. However, there were cases where cracks occurred in the hopper due to vibrations or impacts, and bridging could not be resolved, so we tried the Blowtisc. As a result, it provided sufficient benefits and has been continuously adopted. 【Overview】 ■ Material: Mold sand ■ Characteristics: Slightly sticky and prone to bridging ■ Issues: Unable to resolve cracks and bridging in the hopper * For more details, please refer to the PDF materials or feel free to contact us. * Our website features numerous implementation examples, which can be checked via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0180 Preventing bridge formation of metal powder

0180 Preventing bridge formation of metal powder

By setting it up, the bridge is prevented, allowing for stable discharge of raw materials.

We would like to introduce a case where our "BroadiDisk" provided a solution. Moist materials in the hopper formed a bridge above the discharge screw feeder. Originally, an electric vibrator was installed, but by installing our device, the bridging was prevented, allowing for stable discharge of the raw materials. After reviewing the hopper drawings and based on past experiences, we guided the recommended installation position, which led to the implementation of our solution. We can provide information tailored to individual conditions regarding installation positions and operating methods, so please feel free to consult us. 【Overview】 ■ Material Name: Metal Powder ■ Particle Size: Average, approximately 20 microns ■ Moisture Content: Several percent * For more details, please refer to the PDF materials or feel free to contact us. * Our website features numerous case studies, which can be accessed through the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Introduction of powdered activated carbon injection equipment into the silo.

Introduction of powdered activated carbon injection equipment into the silo.

Installation of the upper hopper section of the vibrating discharge device located at the bottom of the silo.

Here is an introduction to a case solved by our "Brodisk." The introduction of our bridge prevention device was implemented in the hopper section of a powdered activated carbon storage silo. There is a vibrating discharge device at the bottom of the silo, and the installation is in the hopper section above it. We installed eight standard Brodisks and used a controller that incorporates four solenoid valves to sequentially activate two Brodisks at four locations. [Overview Specifications] ■ Silo Diameter: 3000φ ■ Discharge Rate: Approximately 5m3/hr ■ Chemical Name, etc.: Powdered Activated Carbon (Moisture content below 5%, Apparent specific gravity around 0.2) *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous implementation examples, which you can check via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0467 Preventing clogging of flux powder

0467 Preventing clogging of flux powder

Concerned about wear on the inside of the hopper, a wear-resistant urethane rubber sheet has been applied to the equipment installation area!

This is an introduction to a case where the Brody Disk Mini was used as a countermeasure for blockages at the discharge section of a small hopper. The user was concerned about wear on the inner surface of the hopper, and decided to attach a wear-resistant urethane rubber sheet to the installation area of the equipment at the time of adoption. We believe that this equipment is extremely effective in preventing bridging compared to vibration or impact-type bridge breakers. However, the installation position is very important, so please feel free to consult us. 【Case Overview】 ■ Hopper Overview: Square hopper (3 sides inclined, 1 side vertical) discharge section 50φ ■ Target Material: Welding flux fine powder ■ Special Notes: Concerned about wear on the inner surface of the hopper, a wear-resistant urethane rubber sheet was attached to the installation area of the equipment at the time of adoption. *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0691 Bridge prevention of HD-PE crushed material

0691 Bridge prevention of HD-PE crushed material

Case study on resolving bridging issues in the hopper of high-density polyethylene grinding materials!

We would like to introduce a case where "Brodisk" was adopted at a facility engaged in resin molding for automotive parts and various containers. A bridge occurred in the hopper for crushed high-density polyethylene, and this device was installed to prevent it. The problem was solved in one go. In this case, there was a request to try the device before purchase, so we lent out the actual product for them to confirm its effectiveness. 【Case Overview】 ■ Target Material - Crushed high-density polyethylene - Size approximately 3-5mm ■ Hopper - 450×450 - 3-sided incline (about 45°) *For more details, please download the PDF or feel free to contact us.

  • Other powder equipment
  • Mixer/agitator

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Related Categories of Bridge prevention device

COPYRIGHT © 2001-2025 IPROS CORPORATION ALL RIGHTS RESERVED.