松尾産業 List of Products and Services

Until now, it has been difficult to measure extremely thin prepreg sheets and carbon fiber prepreg sheets, but it is now possible to measure gel time while keeping them in sheet form. Measurement of liquids and powders is also possible. - Direct measurement of sheet-like materials eliminates the need for powdering PCB prepregs. Direct measurement of PCB prepregs, carbon prepregs, etc. is possible. Measurement of RCC (resin-coated copper foil) is also possible. - Measurement from thin to thick materials with a single sheet. Supports from 10um ultra-thin prepregs to thick non-woven fabrics. - Measurement of powder and liquid samples that was difficult with the stirring torque method. Broad compatibility with samples containing highly filled fillers, anaerobic samples, gel-like samples, etc. - Visualization of curing behavior in graphs. Calculates and graphs viscosity, phase difference, shear modulus, etc. from the measured stress. - Measurement of the viscoelasticity of fluids. Rheological measurement of non-Newtonian fluids such as samples that do not cure. - Confirmation of stress, viscosity, and phase data is possible. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/gel-time-tester/

• Testing Equipment and Devices

To conduct effective and accurate analysis in the manufacturing field, it is important to objectively analyze actual data rather than relying on the experience or intuition of the measurer. The gel time measurement device "Madoka" can measure gel time with good reproducibility, eliminating the need for skilled techniques. Statistical methods can be employed to improve the efficiency of quality control operations. Challenges in Gel Time Measurement ■ Skilled techniques are required for measurement → By simply selecting the registered measurement conditions, the same results can be obtained regardless of the skill level of the person measuring. ■ Standardization of measurement criteria is difficult → Automated measurement allows for operation under the same conditions between factories and suppliers. ■ It takes time to compile the vast amount of data measured By utilizing dedicated software, management charts, Pareto charts, and histograms for the necessary resins and lots/periods can be easily created. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/madoka/

• Testing Equipment and Devices

The measurement samples (gel-like liquids, sheets, solids) are measured between two metal test heads with known thermal conductivity (aluminum or copper) in the shape of a cylinder or rectangular prism. The temperature gradient ΔT and heat flow Q in the sample are measured, and the effective thermal resistance Rtheff is determined. By applying pressure and changing the thickness of the sample while repeating the measurements, the thermal conductivity (W/m·K), thermal resistivity (mm²·K/W), and interfacial thermal resistivity (mm²·K/W) of the sample can be calculated using the formulas and graphs below. TIMA5 is a groundbreaking device that can control the sample thickness (gap), pressure, or sample temperature for measurements. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/thermal-interface-material-analyzer/

• Temperature and humidity measuring instruments

Non-contact measurement of thermal diffusivity Wide measurement range - from organic films to diamonds - Continuous measurement in vertical and horizontal directions - visualization of anisotropic samples - Mapping measurement available - visualization of defects, unevenness, voids, etc. in samples - High degree of freedom in specifying measurement locations Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/thermowave-analyzer/

• Temperature and humidity measuring instruments

The roll-to-roll pilot coater "VCML" is a multifunctional test coater capable of printing, coating, and laminating on flexible materials such as films, roll paper, and metal foils. 【Features】 ■ Supports over 12 types of printing/coating/laminating with head exchange ■ Compact size (integrated control panel) Machine dimensions: 2.5m (L) × 1m (W) × 1.8m (H) Web width: 300mm (max) ■ Sample coating possible with just a few hundred cc of material, allowing for easy sampling from several meters to hundreds of meters ■ Easy operation with a color touch panel ■ Easy cantilever-style exchange for unwind and rewind shafts ■ Dryer options available (hot air drying / IR / UV) ■ Internet option available for remote diagnosis of the machine Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/vcml/

• Printing Machinery

The tabletop multi-coater has arrived, enhancing operability and reproducibility while maintaining its traditional multi-functionality! 【Features】 ■ By changing the head, you can easily perform bar coating, gravure, gravure offset, flexo printing, and lamination. ■ Coating and printing are possible up to A3 size. ■ Anyone can achieve accurate coating without any deviation easily. ■ You can create samples that correlate with the production line using a small amount of ink, reducing waste of expensive materials. ■ Printing and lamination can be done on any flexible substrates such as paper, film, and metal foil. ■ You can print and compare two or more types of ink simultaneously, allowing for alignment for overprinting. ■ Equipped with a touch panel for user-friendly operation. Demonstrations are currently being accepted at the Shin-Yokohama demo room! Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/k303-multi-coater/

• Printing Machinery

To ensure that customers looking for testing machines can purchase with confidence and satisfaction, we offer free testing of various products in our demo room. You can try out printing and coating of various materials, UV curing, UV curing verification, shrinkage rate, and stress measurement. - Products Available - ■ Printing Testing Machines - Roll-to-Roll Lab/Pilot Coater 'VCML' - Desktop Automatic Test Coater 'K303S' and others Various printing testing machines for gravure printing, flexo printing, bar coaters, coating, lamination, etc. ■ Automatic Gel Time Measurement Device 'Madoka' Automatically measures gel time for thermosetting resins and more. ■ UV-LED Irradiator Convenient tabletop models for research and development purposes. ■ Film Thickness Gauge Easily measures thickness by simply setting the film cut from the production line. ■ Infrared Moisture Meter Easy operation for non-contact, non-destructive, and high-speed measurement. Online demos and rental of demo machines are available depending on the product. To apply for a demo, please fill out the necessary information in the form below and contact us. https://www.matsuo-sangyo.co.jp/contact/contact-demo-request/

• Testing Equipment and Devices

Efficient and qualified testing possible with a small amount of materials! We offer a variety of tabletop automatic test coaters for research and development in nanotechnology and coatings. 【Features】 ■ Printing and coating on various flexible substrates such as films, paper, and metal foils are possible. ■ Compatible with various coating liquids including water-based, solvent-based, and UV. ■ Easy operation allows for accurate coating without fluctuations. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ ★ Testing and online demos are available at the Shin-Yokohama demo room! Please request through the inquiry page or our company website. Demo request page▼ https://www.matsuo-sangyo.co.jp/contact/contact-demo-request/ For quotes and purchases of bar coaters and other manual test coaters, visit tofu LABO! *Quotes can also be obtained from the inquiry page. The "tofu LABO" link is below▼

• Other painting machines

The "FlexiProof 100/100UV" is a tabletop flexographic printing proofing machine. It can produce proof prints equivalent to production machines at a high speed of up to 99m/min, allowing for checks on quality, abrasion resistance, and flexibility without stopping the production machine. It contributes to reducing production machine downtime, creating samples, and improving quality management efficiency. Additionally, the anilox pressure and printing pressure can be easily adjusted using a dial gauge, and it is capable of printing on delicate materials such as aluminum foil and tissue. Anilox replacement and cleaning can be done easily, and a UV curing device-equipped type is also available. 【Examples of Applications】 - Development of flexo inks for printable electronics - Design development using flexo process printing - Simulation of setting conditions for flexo printing - Development of conductive inks for antenna circuits of IC tags Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/flexiproof-100/

• Testing Equipment and Devices

You can instantly create high-quality print samples of inks used in gravure printing machines. It is equipped with necessary functions for those using liquid inks or involved in manufacturing. Ideal for R&D, computer color matching data, quality control, and printing sample production. ■Features - Capable of printing on any flexible material - Excellent print suitability with printing speeds of up to 100m/min - Easy-to-clean quick-release doctor blade - Uses electronic engraving plates - Microprocessor-controlled servo motor drive - Control of printing pressure and doctor pressure via air pressure - Coating targets: paper, film, metal foil ★ Testing available at the Shin-Yokohama demo room, online demos also accepted! Feel free to contact us. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/gp-100/

• Printing Machinery

- Coating can be done with easy setup. - Since testing can be done with a small amount of ink, it reduces waste of expensive materials. - Ideal for research and development, including quality control, print suitability testing, and computer color matching. - You can control pressure and speed, allowing for the creation of highly reproducible samples. - Bars can be supplied up to 400-500um (wet film thickness). - Optional gap applicators and K-Rocks (flexographic printing) are available. ★ Testing is currently available at the Shin-Yokohama demo room! Online demos and demo machine rentals are also possible. Please feel free to contact us. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/k-control-coater/

• Painting Machine

■Features - Compact and lightweight, it can be installed in various locations. - It uses actual ink, and with head replacement, it can easily perform gravure, gravure offset, flexo printing, and lamination. - It can print on various materials such as film, paper, aluminum foil, metal foil, and PVC. - It allows for simultaneous printing of two or more inks for comparison and alignment for overprinting. - It enables testing with a small amount of ink, reducing waste of expensive materials. - Ideal for research and development, including quality control, print suitability testing, and computer color matching. It is also suitable for printed electronics research and development. - A product from RK, which boasts over 60 years of experience in more than 40 countries worldwide. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/k-printing-proofer/

• Printing Machinery

- Anilox rollers can be easily replaced. - Ceramic anilox rollers can accommodate up to 850 lines per inch. - There are also micrometer types that allow for fine adjustments of printing pressure. - Testing can be done with a small amount of ink, reducing waste of expensive materials. - Coatings: Flexo inks (water-based, solvent-based, UV) - Application targets: Film, paper, metal plates/foils, glass, ceramic plates === Introduction to the Demo Room === If you bring samples and materials, experiments such as coating, gravure printing, and flexo printing can be conducted. You can try out the actual usability and experiment results. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/esiproof/

• Printing Machinery

- Supports wet film thickness of 400 to 500 μm. - Anyone can easily and quickly create samples with a small amount of material. - By changing the gauge, samples of different film thicknesses can also be easily made. - Using a dedicated printing table ensures high reproducibility. - While actual machines may be used for sample creation, they consume a large amount of material and require significant time for preparation, setup, and cleanup, which is not necessary with a bar coater. - There are coating machines for experimental use, such as film applicators, but they have a narrow coating width and are difficult to use on materials that are prone to warping. - The bar coater can apply coatings up to approximately 300 mm wide and can be used on materials such as flexible copper foil, aluminum foil, plastic film, paper, and fabric, and it can accommodate various coatings including paints, inks, and adhesives. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/k-hand-coaters/

• Printing Machinery

Product Lineup ■ Bar Coater (Wire Bar) Core diameters: 1/4 inch, 1/2 inch, 3/8 inch Various sizes are available. ■ Select Roller Easily achieve uniform thin film application! Wireless bar with no disconnections. Easy cleaning and maintenance! ■ A-Bar High washability, no wire breakage, long-lasting wireless bar. For purchases, please visit the dedicated EC site for Bar Coaters - Tofu LABO - at the following page ▼ http://www.tofulabo.com/ Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details on the Bar Coater (Wire Bar), click here ▼ https://www.matsuo-sangyo.co.jp/products/bar-coater/

• Printing Machinery

Easy and simple! Manual printing test machine bar coater. It can be used as a tool for creating color samples and evaluation samples. Bar Coater (Wire Bar / Meyer Bar) 【Features】 ■ A device for evenly applying liquids such as inks, paints, and adhesives. ■ A stainless steel rod is wrapped with stainless steel wire. ■ The grooves of the wire allow for adjustment of the liquid application amount, achieving a stable film thickness. ■ The film thickness varies depending on the wire gauge (diameter). ■ It can be easily applied with both hands. ■ It allows for uniform application of a consistent film thickness with a small amount of ink. ■ It can be applied to flexible materials such as copper foil, aluminum foil, plastic film, paper, and fabric. Purchase the bar coater here▼ Tofu LABO http://www.tofulabo.com/ Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For more details on the bar coater, click here▼ https://www.matsuo-sangyo.co.jp/products/bar-coater/

• Printing Machinery

The "Select Roller" is a manual test coater with a handle that allows for easy and uniform thin film application. It uses a coating bar with a screw-like uneven surface that is integrally molded onto a stainless steel rod, eliminating issues such as disconnection and loosening found in traditional bar coaters. It is resistant to clogging and has excellent cleanability, making it ideal for coating experiments with inks, paints, adhesives, varnishes, and more. 【Features】 ■ Film thickness can be adjusted from a wet film thickness of 1.5μm to 150μm ■ Available in two coating widths: 60mm and 250mm ■ A convenient set of 10 with a carrying case is also available *Demo units are available for loan. For more details, please contact us or download the PDF for more information. For details and purchase of the wireless bar, click here ▼ Tofu LABO http://www.tofulabo.com/ Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/select-roller/

• Testing Equipment and Devices

- No sample cutting required, measurements can be taken on-site - Confirmation of wettability changes after surface treatment (modification) - Compact and easy to carry: 110(W)×50(D)×110(H)mm - Measurements can be taken at the site or manufacturing location - Can be used as a substitute for a dyne pen or wettability test - Data (images and contact angles) can be saved on a PC - Measurement starts with the push of a button 【Features】 - Measurement is easy to operate with a single button, allowing for smooth workflow. - Liquid sample replacement is simple and can be done by just swapping syringes. - Time-dependent measurements can be taken with image capture at 30 frames per second. - Surface tension measurement and surface free energy analysis using the sessile drop method are also possible. - Measurements can be conducted while confirming the droplet deposition point. - Can serve as a substitute for dyne pens and wettability reagents. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/contact-angle-meter/

• Other measurement, recording and measuring instruments

The "Film Tester" has been updated! It simplifies operation and reduces measurement variability caused by human factors! Place the film cut from the line on the measurement platform, and just lower the lever to set it up. Measurement will automatically stop at the end point of the film. The measurement results are automatically saved in CSV format on your PC, allowing for editing and comparison with dedicated software. 【Features】 ■ Achieves high-precision measurement with a resolution of 0.01μm and repeatability of 0.2μm ■ Continuous measurement is easy for anyone to perform ■ Measurement probes are available according to the measurement target ■ In addition to high-end models, we also offer machines with suction tables and compact models Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/continuous-film/

• Coating thickness gauge

The original air release ensures a constant descent speed of the measuring element. It reduces damage to the film and minimizes variability caused by the measurer. 【Features】 ■ Achieves high-precision measurement with a resolution of 0.01um ■ Easy measurement for anyone ■ Due to low measurement pressure, it minimizes damage to the film and allows for accurate measurements. ■ You can choose a model with the necessary resolution according to your application. *Testing is available at the Shin-Yokohama demo room, and online demos are also accepted! Please feel free to contact us. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/continuous-film-hkt/

• Coating thickness gauge

Handy Series The original air release ensures a constant descent speed of the measuring device. It reduces damage to the film and minimizes variability caused by the operator. 【Features】 ■ Easy to measure anywhere ■ Low measuring pressure minimizes damage to the film, allowing for accurate measurements. ■ A wide range of options available *Testing is currently available at the Shin-Yokohama demo room! Online demos are also being conducted. Please feel free to contact us. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/continuous-film-handy/

• Coating thickness gauge

Manual measurements often vary in methods and criteria depending on the measurer, leading to significant measurement errors. "Madoka" can obtain high-precision and stable data regardless of the measurer's skill. 【Measurement of Various Resins Possible】 Epoxy, silicone, urethane, PVC, unsaturated polyester, phenol, prepreg, EMC, encapsulants, sealing materials, adhesives, inks, etc. 【For Those Facing Such Issues】 ◆ Want to eliminate "ambiguous" judgment criteria based on human perception ◇ Want to standardize measurement criteria between factories and streamline quality control operations ◆ Want to manage measurement result databases and conduct data analysis collectively ◇ Want to automatically output measurement data to a server 【Features】 ■ Heating plate temperature rise: Measurement starts just 5 minutes after power is turned on ■ Can be set from room temperature to high temperatures up to 300℃ ■ Measurement results are graphed as torque curves to confirm curing behavior Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details here▼ https://www.matsuo-sangyo.co.jp/products/madoka/

• Testing Equipment and Devices

■ High-Power Water-Cooled Type - Available in 4 wavelengths (365nm, 385nm, 395nm, 405nm) - This is a high-power water-cooled, bar-type UV-LED irradiator. ■ Bar Type - MS-B Series - A high-power UV-LED light source available in 4 wavelengths (365nm, 385nm, 395nm, 405nm) - The high-power bar-type UV-LED irradiator can be mounted on a tabletop conveyor. - It adopts a forced air cooling method, eliminating the need for a chiller. ■ Area Irradiation Type - MS-A Series - Available in 5 wavelengths (275nm, 365nm, 385nm, 395nm, 405nm) - Achieves a compact, lightweight, high-power area irradiation type UV-LED irradiator with air cooling. ■ Small Handheld Type - MS-H Series A lightweight and compact small handheld UV-LED irradiator. - Available in 4 wavelengths (365nm, 385nm, 395nm, 405nm). - It has become even easier to use when combined with a dedicated box with an up-and-down mechanism (optional). Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/

• Ultraviolet irradiation equipment

- This is a high-output water-cooled, bar-type UV-LED irradiator. - Illuminance: 8,000 mW/cm² (WD: 10mm, 365nm) - Wavelengths of 365nm, 385nm, 395nm, and 405nm can be selected. - The irradiation window size is 75×5mm and customization is also available. ★ 5 minutes on foot from Shin-Yokohama Station. Testing is currently available in the demo room! Online demos are also being conducted. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/ms-v/

• Other physicochemical equipment

- The bar-type high-output UV-LED irradiator can be mounted on a tabletop conveyor. - Wavelengths of 365nm, 385nm, 395nm, and 405nm can be selected. - It adopts a forced air cooling system, eliminating the need for a chiller. - The irradiation window sizes are 217×24mm and 425×24mm. Customization is also available. - Conveyor safety measures options: light-shielding cover, under cover/free roll, interlocked wing doors, emergency stop switch, and more. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/ms-b/

• Other inspection equipment and devices

- We have achieved a compact, lightweight, air-cooled high-output area irradiation type UV-LED irradiator. - Customization options are available according to your needs, including larger irradiation areas, circular types, and segmented irradiation functions. - The MS-A0202 series has added a wavelength of 275nm. - Wavelengths of 275nm, 365nm, 385nm, 395nm, and 405nm are selectable. Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/ms-a/

• Other inspection equipment and devices

- This is a lightweight and compact handheld UV-LED irradiator. - It is easy to carry and can be used conveniently. - You can choose from four wavelengths (365nm, 385nm, 395nm, 405nm). - It has become even easier to use when combined with a dedicated box with an up-and-down mechanism (optional). Download the catalog here ▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here ▼ https://www.matsuo-sangyo.co.jp/products/ms-h/

• Other inspection equipment and devices

■Features - Achieves high-resolution measurement through a three-wavelength method - Enables non-contact, non-destructive, and high-speed measurement - Capable of measuring semiconductors, liquid crystals, films, chemicals, fibers, paper, solvents (liquids), powders, ceramics, paints, and more 〇Fiber-type infrared moisture meter - Capable of measuring in diverse environments - Real-time measurement with high-speed analog computation - Handy type for easy portability 〇Wide-area irradiation type infrared moisture meter - Capable of measuring moisture on wide and uneven surfaces - Real-time measurement with high-speed analog computation - Easy setup for any scene using universal parts *Testing is available at the Shin-Yokohama demo room, and online demos are also being accepted! For more details, please refer to the PDF materials. Feel free to contact us. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/moisture-meter-sensor-fiber/

• Other measurement, recording and measuring instruments

Diamond is an insulator, but it can acquire conductivity by doping with boron. We will uniformly deposit conductive diamond over a large area while maintaining the chemical stability and strength of diamond. Diamond electrodes have a wide potential window, allowing for the decomposition and synthesis of difficult-to-decompose substances through oxidation and reduction reactions. By electrolyzing tap water with diamond electrodes, it is possible to directly produce high-concentration ozone water. Additionally, our unique pre-treatment for film formation improves the adhesion of the diamond film. *For more details, please contact us or download and view the catalog.

• Other semiconductors

This is an aluminum nitride filler that combines high thermal conductivity and insulation properties. Surface-treated products are also available to improve fillability and water resistance. ■ High Thermal Conductivity Large Particle Size Sintered Filler The filler made from spherical sintered aluminum nitride (AlN) micropowder excels in fillability into resins and can significantly increase thermal conductivity, making it suitable for applications such as heat dissipation sheets. As the miniaturization and high integration of electronic components progress, heat dissipation has become a major challenge, and aluminum nitride fillers contribute to improved heat dissipation. ■ High Purity Aluminum Nitride Powder This aluminum nitride filler is produced using the direct nitriding method. It is adopted in various fields, including electronic devices and semiconductor manufacturing equipment. We offer grades tailored for "sintering," "filler," and other applications to meet diverse needs. Download the catalog here▼ https://www.matsuo-sangyo.co.jp/catalogs/ For product details, click here▼ https://www.matsuo-sangyo.co.jp/products/aluminum-nitride-filler/

• aluminum

PDLC (Polymer Dispersed Liquid Crystal) dimming film is a functional film that can switch between a cloudy and transparent appearance by turning an AC power source ON/OFF. It can also be used as a projection screen.

• Other office supplies

Ethylene sulfate (DTD) is gaining attention as one of the additives for electrolytes in lithium-ion secondary batteries and has become a widely used general-purpose material in China, a major producer of LiBs worldwide. By incorporating ethylene sulfate into the electrolyte, the following effects can be expected: - Improved electrical conductivity of the battery, enhancing charging and discharging efficiency - Increased stability of the battery in high-temperature environments - Extended cycle life of lithium-ion batteries

• Lithium-ion battery

Catalysts based on dibutyltin dilaurate (DBTDL), which possess excellent chemical reactivity and are easy to handle, have been widely used in the production of polyurethane resins used as materials for high weather-resistant coatings. However, due to the designation of dibutyltin dichloride as a substance of very high concern under the European REACH regulation, there has been a demand for tin-free alternatives. Borchers' "tin-free catalysts" can comply with regulations on organic tin and are designed with environmental considerations in mind, being free of tin. You can adopt catalyst types that meet your requirements while capturing the characteristics of individual catalysts, such as those based on Bi, Zn, and Li, or combination-type catalysts. 【Features】 ■ Compliance with organic tin regulations ■ VOC reduction ■ High performance as a DBTDL alternative ■ Water-based catalysts *For more details, please refer to the PDF document or feel free to contact us.

• Other polymer materials

This product is a cobalt alternative drying agent for paints and inks that can achieve energy-saving measures through low-temperature curing with a curing time equivalent to or longer than cobalt. Borchers has developed "Borchi Oxy Coat" as a substitute for cobalt dryers in oxidation polymerization drying systems, such as unsaturated polyesters. It is possible to achieve drying speed, high gloss, and low haze with a very low additive amount. 【Features】 - Contributes to energy savings and CO2 reduction through low-temperature curing considerations - Cobalt-free drying agent compliant with environmental regulations - Consideration of cobalt alternatives in anticipation of increasing cobalt demand

• Other metal materials

We can provide not only traditional solvent-based drying agents but also drying agents for high solids and water-based paints and inks. We offer multiple types of metals. 【Features】 ■ Drying promotion ■ Reaction promotion ■ Water-based compatibility *For more details, please refer to the PDF document or feel free to contact us.

• Fats and oils

Borchers' wetting dispersants are high-performance dispersants designed to disperse organic and inorganic pigments in water-based and solvent-based paints. Dispersing pigments not only takes time during the manufacturing process but also consumes energy; however, using this product can significantly reduce grinding time, saving time, costs, and energy. By selecting the appropriate wetting dispersant, you can enhance gloss and color strength while stabilizing the paint. 【Features】 ■ Provides suitable wettability ■ Reduces grinding time ■ Improves color quality ■ Enhances transparency

• Other polymer materials

Borchers' water-based paint and coating rheology modifiers are low to high shear polyurethane, acrylic, and zirconium composite thickeners. They ensure optimal flow and leveling while significantly impacting the storage stability and application properties of coating systems. They can also be used for polyurethane dispersions (PUD) for artificial leather, gaining attention for their compliance with the recent leather-free requirements. They are REACH compliant and designed to be free of tin. 【Features】 ■ REACH compliant ■ Tin-free ■ VOC-free ■ Improved storage stability ■ Enhanced application properties ■ Appropriate flow and leveling properties ■ Prevention of sagging

• Other metal materials

Conductive polymers are polymer compounds (such as plastics) that possess electrical conductivity. They are widely used in everyday electronic devices such as touch panels, capacitors, and organic EL displays for applications like transparent electrodes and antistatic agents. The conductive polymer handled by Cleva is "PEDOT/PSS," which has the highest stability and conductivity. However, it cannot be used in its raw form alone; it must be mixed with additives such as surfactants (which adjust the spreading degree on a surface) tailored to the target substrate, as well as additives to adjust the dynamic viscoelasticity of PEDOT/PSS, and binders to ensure uniform application and adhesion to the substrate. This conductive polymer ink (liquid) demonstrates electrical conductivity when applied to the target substrate.

• Other polymer materials

This is an SS-type magnetron power supply with an extremely stable oscillation frequency. ◆ The frequency remains stable even when the output is varied. ◆ Output synthesis is possible through parallel operation. ◆ The matching accuracy is greatly improved.

• power supply
• power supply

【Glass Molding Lens Business】 Aspherical glass lens molding is a processing method that involves heating glass materials and pressing them with molds from above and below to create optical lenses. While it allows for the creation of free curves, forming aspheres with varying curvatures within the lens requires very challenging technology, considering the relationship between the physical properties of glass and temperature. Our company has advanced technology development, enabling mass production not only of large-diameter lenses exceeding 30mm, which were traditionally considered difficult to manufacture, but also of large-diameter lenses exceeding 50mm. 【Mold Release Film Business】 Mold release films for molding require harsh conditions. - The release film must withstand high temperatures. - It must have smooth slip properties for softened glass to spread easily. - Even under severe conditions, it must firmly adhere the mold and the film together. In place of the conventional rare metal-based films, our company has developed a new material for release films. 【Mold Business】 We manufacture molds with the optimal materials, shapes, and delivery times tailored to our customers' objectives. 【Prototype Business】 We position prototyping, the first step in product development, as one of the most important aspects. We provide speedy responses and short lead times for prototypes.

• Contract manufacturing

A laser power sensor is a device that converts laser light into thermoelectric power to measure laser output. The receiving surface is treated to efficiently absorb laser light. Our proprietary thin-film elements are used in the thermopile that generates thermoelectric power. * If you provide us with specifications, we can also manufacture sensors other than those listed below. ★ Detailed specifications can be viewed by downloading the catalog ★

• Laser Components