マコー List of Products and Services

By using fine abrasives for oxide scale removal, a smooth finish surface similar to acid pickling can be achieved. Compared to acid pickling, it involves fewer processes and the equipment is compactly designed. Although a fine powder called abrasive is used, there is no dust generation due to the wet processing, and a dust collector is not required.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― - Operators only need to replace the pallets for easy operation. - Supports a variety of workpieces with simple setup changes. - Automatic processing that targets while rotating the workpiece.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― • A nozzle with a width of 630mm can be operated in the X-axis direction, allowing for uniform processing of an area up to 750×600mm. • The operation position and speed of the gun, as well as the ON/OFF of the blast projection, can be programmed using a teaching pendant.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― • By alternately switching between the blast section and the work set section in two stages, work can be set even during processing. • The X-axis drive allows the gun to move left and right, and the θ-axis drive tilts the gun in three positions, enabling processing of the top and sides of three-dimensional workpieces. • The safety door at the front closes during table inversion to prevent entrapment. • During inversion, a shutter that separates the blast section and the work set section opens and closes vertically, preventing the blast liquid from splattering into the work set section and keeping noise levels low.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― - Supports detailed teaching with a multi-joint robot and servo-driven rotating table. - Capable of creating motion programs that operate within a specified numerical range multiple times with the press of a single switch. - Functionality limited to wet blast processing. Simple design with daily management focused solely on slurry concentration. - Uses high-wear-resistant parts in accordance with mass production equipment. Can be used as a medium-volume production machine if dedicated jigs are manufactured.

• Other processing machines

Features ―――――――――――――――――――――――――――――――― - Continuous automatic wet blasting, rinsing, and drying of thin plate workpieces in a strip shape. - A compact, low-cost device that condenses functionality while maintaining the processing quality of wet blasting. - The blasting and rinsing sections are compact, allowing maintenance of the drive components simply by opening the conveyor cover. Additionally, the key components, such as the wide nozzle and pump, are designed for high durability.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― • By rotating the barrel, the workpieces are efficiently agitated inside, allowing for comprehensive processing of complex shapes and flat workpieces. • Performing a coarse water wash after blasting washes away any abrasive material adhering to the workpieces, reducing carry-out. • A timer setting for the blasting time creates a uniform processing surface.

• Other processing machines

• Large parts such as bike frames, mufflers, and wheels can be fully processed indoors. • By combining a turntable and gun swing, full surface processing can be easily achieved. • Equipped with double doors for easy access to large workpieces.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― • A nozzle with a width of 320mm can operate in the X-axis direction, capable of uniformly processing an area of up to 600×320mm • Various workpieces can be accommodated by changing the fixtures • The teaching pendant allows programming of the gun's operating position, speed, and the ON/OFF of the blast projection

• Other processing machines

Features ――――――――――――――――――――――――――――――――― • Ergonomically designed equipment that does not cause fatigue even after long hours of operation. • The parts in contact with the material are made of all stainless steel, excellent in rust resistance and durability. • A blast chamber that can accommodate 15-inch wheels with tires without modification. • Equipped with a wiper to eliminate obstructions to visibility during processing. • Start and stop operation using a footswitch. • Convenient with casters for easy mobility.

• Other processing machines

Features ――――――――――――――――――――――――――――――――― • Ergonomically designed equipment that does not cause fatigue even after long hours of operation. • Stainless steel body with truss structure, achieving strength and lightness. • Wide and bright work window that provides a sense of openness. • Includes a wiper that eliminates obstructions to visibility during processing. • Enhanced durability, allowing the use of various abrasives such as grinding and polishing materials. • Equipped with convenient casters for easy mobility.

• Other processing machines

- Uniform Processing By using a wide-range gun unique to Makoh to scan the processing target area, we achieve uniform processing across the entire surface with high productivity. - Excellent Processing Reproducibility The single-axis drive is servo-controlled. It is possible to create operation programs that allow for multiple operations within a specified range with just one switch. - Simple Configuration Functionality is limited to wet blast processing only. Daily management is designed to be simple, focusing solely on slurry concentration. - High Durability We use highly wear-resistant parts that conform to mass production equipment standards. If dedicated jigs are manufactured, it can also be used as a medium-scale production machine.

• Other processing machines
• Testing Equipment and Devices

- Compatible with various materials Wet blasting with water, compressed air, and abrasive materials allows for the removal of scale regardless of the material, such as alloy steel, carbon steel, and special steels (stainless), due to its physical processing capabilities. - Scale removal with grit-shaped abrasives Scale from special steels, which is difficult to remove even with shot blasting or pickling, can be thoroughly eliminated using grit-shaped abrasives. - Easy maintenance Maintenance requires infrequent part replacements and is straightforward. Additionally, there is no dust generated during operation. - "All-in-one" from scale removal to water drainage The wet blasting process for scale removal is integrated into a compact system that includes washing and water drainage.

• shaft
• Metal bearings
• Spring

In the physical processing of wet blasting, we perform surface modification of engineering plastics and super engineering plastics that have high resistance to adhesion and chemicals, dramatically enhancing the adhesion of coatings and plating. - Wet blasting not only removes debris and release agents that hinder adhesion but also improves adhesion by increasing the surface area through the formation of fine irregularities. - The basis for the improved adhesion lies in two factors: enhanced wettability and the anchor effect. By stripping away a thin layer of the surface, a fresh surface is exposed, improving wettability. Additionally, the fine irregularities created by the abrasive material act as a physical anchor effect, which together create an optimal surface for adhesion, enabling ideal plating and coating.

• High frequency/microwave parts
• Automotive Connectors
• EMC countermeasure products

Bonded processing has long been the industry standard for cold forging lubrication treatment due to its high lubricating performance and versatility; however, issues such as industrial waste generation, deterioration of working environments, and energy costs have arisen. Additionally, while the one-component lubricant developed as an alternative excels in both environmental compatibility and forging performance, there were no devices made by manufacturers to fully utilize its capabilities. Mako has achieved forging performance that surpasses bonded processing through a technique called wet blasting for surface preparation. This has been consolidated into a device called 'WLS' that integrates the lubrication treatment from surface preparation to application.

• Axle parts
• Metal bearings
• Engine parts

"Wet blasting" is a technology that uses a mixture of water and abrasives, which is sprayed at high speed with compressed air to clean, process, and improve the surfaces of metals, plastics, ceramics, and more. Due to the wet processing, it is possible to use small abrasives on the order of a few micrometers, making it suitable for fine processing. Additionally, cleaning such as degreasing and rust removal can be performed simultaneously with processing such as roughening. 【Features】 ■ Enables the use of fine abrasives due to the transport effect of water ■ No dust generation due to the wet environment ■ No processing heat or static electricity generated ■ Achieves an all-closed circulation system ■ Can process materials without selecting the type of object For more details, please refer to the catalog or feel free to contact us.

• Other abrasives
• Other machine tools
• Other surface treatment equipment

This catalog features products for maintenance from a company engaged in the planning, design, manufacturing, and sales of wet blast equipment. It includes maintenance-oriented devices such as the compact manual device "Small Manual Machine," the "Medium Manual Machine" capable of processing up to φ600×500mm, and the "Large Manual Machine" equipped with a turntable. [Contents] ■ Maintenance-oriented devices *For more details, please refer to the catalog or feel free to contact us.

• Other cleaning
• Other contract manufacturing

This technology is a cleaning method that improves the work environment without using chemicals or agents. It prevents fires caused by solvents and dust-related disasters, safely removing dirt. After removing the dirt, it restores a shine comparable to new. Additionally, it is possible to clean parts that are directly covered in oil or rust without any pretreatment. 【Features】 ■ High safety ■ Excellent cleaning ability ■ Maintains a clean environment ■ No pretreatment required *For more details, please refer to the catalog or feel free to contact us.

• Other cleaning

"Wet blasting" is a physical surface treatment method that mixes particles (abrasives) with a liquid (mainly water) and atomizes and projects them using the expansion force of compressed air, allowing for fine surface processing and cleaning. Additionally, due to the wet environment, dust is not generated. Furthermore, cleaning, degreasing, and rust removal can be performed simultaneously. This method can be applied to various materials without the use of harmful chemicals or solvents, making it an environmentally friendly surface treatment technique. 【Features】 ■ No dust generation ■ Cleaning and degreasing possible ■ Rust removal possible *For more details, please refer to the catalog or feel free to contact us.

• Other cleaning
• Other contract manufacturing

The "Closed System" is a system that can significantly reduce wastewater and waste. Traditionally, there were issues such as the need for wastewater treatment, the need for secondary waste treatment like abrasives and grinding dust, and weak processing power. The new "Closed System" has achieved zero-emission and significant waste reduction by using a special stainless steel abrasive. 【Features】 ■ Significantly reduces wastewater and waste ■ Uses stainless steel abrasives ■ Enables zero wastewater discharge *For more details, please refer to the catalog or feel free to contact us.

• Other environmental measures and recycling

It is a physical surface treatment method that mixes particles (abrasives) and liquid (mainly water), atomizes and projects them using the expansion force of compressed air, and performs fine surface processing or cleaning.

• Other cleaning machines

A surface treatment device that performs precise physical cleaning of the surfaces of thin materials such as printed circuit boards with a width of 610mm or less and a thickness of 0.2 to 2.0mm. It can uniformly process both sides of the thin material and continuously automate the washing, rinsing, and drying processes. It can be used for cleaning printed circuit boards, removing foreign substances and oxide films, desmearing, surface roughening, and etching.

• Other semiconductor manufacturing equipment