日鉄物産マテックス List of Products and Services

The CALGAVIN-produced "hiTRAN" is a heat transfer enhancement element designed to improve the performance of heat exchangers, particularly intended for use in tubular heat exchangers. By inserting hiTRAN into the tube, turbulence is generated within the tube, significantly improving heat transfer efficiency. The benefits obtained from the hiTRAN heat transfer enhancement element are as follows: ✓ Improvement and enhancement of heat exchanger capacity ✓ Increase in tube-side heat transfer coefficient (up to 16 times) ✓ Reduction in heat exchanger surface area and weight ✓ Reduction in maintenance costs due to decreased fouling ✓ Energy savings due to reduced energy requirements ✓ Lower maintenance and installation costs As fouling inside the tube increases, the performance of the heat exchanger decreases, leading to more frequent cleaning. This occurs because the flow velocity at the tube wall is slow, allowing dirt to accumulate there. As a result, additional energy is required to restore the performance of the heat exchanger, leading to a decline in production efficiency. Naturally, maintenance costs also increase. Here, we will introduce the mechanism of fouling reduction in the tube by hiTRAN. *For more details, please refer to the materials or feel free to contact us.*

• Other machine elements

CALGAVIN is a group of experts providing solutions to various problems related to heat exchangers. - Optimization of plant operations - Removal of plant limitations - Reduction of required energy For these solutions, CALGAVIN has been thoroughly researching the optimization and improvement of heat exchangers in collaboration with universities and research institutions for over 40 years. By inserting 'hiTRAN', a heat transfer enhancement element, into tube-type heat exchangers, both new and existing, various benefits can be obtained: - Reduction in the number of tubes, weight reduction, and decreased installation area - Reduction in initial costs and installation expenses - Increase in heat transfer coefficients - Decrease in heat transfer area - Maintenance of long-term operation by reducing fouling inside the tubes - Increase in production while reducing energy consumption - Reduction of required energy - Decrease in maintenance costs *For more details about the product, please refer to the catalog or feel free to contact us.

• Other machine elements
• Other metal materials

Presezzi Extrusion is the only manufacturer in the world that can support a full line of extrusion centered around extrusion presses. There is a cooling system at the rear of the extrusion press. The "H.E.C.S Cooling System" provided by Presezzi Extrusion is a high-efficiency cooling system featuring a new pattern of air nozzles that improves system efficiency by approximately 25% compared to traditional systems. This system is composed of a high-temperature resistant roll way that can move vertically to process extruded profiles of various heights. FEM analysis is conducted to provide the optimal cooling solution and to give the most accurate temperature for the mechanical properties of the extruded profiles. Presezzi Extrusion can offer various types of concentrated cooling systems depending on the extrusion alloy, profile dimensions, required temperature, and extrusion speed.

• aluminum

■Prevention of Foreign Matter Contamination After inflating the bag like a balloon, moving the straight blade quickly to cut through the middle of the bag results in minimal cutting debris, preventing the trouble of bag fragments contaminating the raw materials. ■99.9% Raw Material Recovery Rate To enhance the recovery rate of powders, an air blow method that injects high-pressure air into the bag is adopted. Our unique technology significantly reduces the loss of raw materials. ■Labor Saving and Environmental Improvement (Compatible with Washable Specifications) Automation from bag supply to opening, discharging, and collecting empty bags achieves significant labor savings. The bag opening machine has a box-type structure that makes maintenance easy. There are many proven results for washable specifications as well. ■Engineering Support for the Entire Line We provide engineering support not only for the bag opening machine itself but also for bag cleaners, various conveyors, elevators, robot depalletizers, and empty bag processing, covering the entire line. ■Conducting Bag Opening Tests We have established a bag opening test facility where bag opening tests can be conducted at any time. It is also possible to send us raw material bags and receive videos and test data from the opening process. You can check in advance the feasibility of opening, contamination checks for paper fragments, the number of bags processed per hour, and the discharge rate. Please feel free to reach out to us.

• Other food machinery
• Other powder equipment
• Other conveying machines

Presezzi Extrusion is the world's only manufacturer capable of providing a complete extrusion line, centered around cutting-edge "extrusion presses" for aluminum extrusion profiles and energy-saving, high-efficiency, high-precision "magnetic heaters." At Presezzi, we conduct a "REVAMPING" business for aging extrusion presses and related equipment. Of course, we can also accommodate extrusion presses manufactured by other companies, not just those made by Presezzi. ◆COMPLETE Overhaul of the entire mechanical, electrical, and hydraulic components of extrusion presses and related equipment ◆PARTIAL Overhaul of only some key components, such as the main cylinder and die platen ◆GREEN Energy-saving upgrades of existing hydraulic equipment by installing main pumps with Presezzi's proprietary technology, "E.S.S." ※E.S.S.: Energy Saving System All new parts being updated are accurately verified based on FEM/FEA calculations and analyses (DNV procedures and regulations). *For more details, please refer to the PDF materials or feel free to contact us.

• aluminum

Presezzi Extrusion is a manufacturer that specializes in extrusion presses for aluminum extrusion profiles and can accommodate a full line of extrusion solutions. The front-loading extrusion press, which is globally mainstream, features high rigidity and top quality, and is equipped with the standard "E.S.S (Energy Saving System)" that contributes to energy savings. This extrusion press is certified with the 'Environmental Product Declaration (EPD)' that provides information on environmental performance in accordance with ISO 14025 standards. EPD Registration Certification No: S-P-06388 https://www.environdec.com The EPD, as an environmental product declaration, is defined as "quantifying environmental information regarding the product's life cycle, allowing for comparisons between products that serve the same function." By owning a Presezzi Extrusion press, you can improve sustainability goals and demonstrate your commitment to the environment. *For more details, please refer to the PDF materials or feel free to contact us.*

• aluminum

The "ZPE (Zero Pollution Energy)" magnetic heater for aluminum billet heating provided by Presezzi Extrusion is an excellent billet heater that can contribute to your energy savings. - Low energy consumption: 165 kWh/ton (heating from 20°C to 480°C) - High heating efficiency: 82% This magnetic heater is certified under the ISO 14025 standard and provides information on environmental performance through the 'Environmental Product Declaration' (EPD). EPD registration certification No: S-P-06355 https://www.environdec.com The EPD, as an environmental product declaration, is defined as "quantifying environmental information regarding the product's life cycle and enabling comparisons between products that serve the same function." Customers who own Presezzi Extrusion's magnetic heater can improve their sustainability goals and demonstrate their commitment to the environment. *For more details, please refer to the PDF materials or feel free to contact us.*

• aluminum

Presezzi Extrusion is the only manufacturer in the world capable of providing a complete "full line" for extrusion, centered around extrusion presses. Extrusion presses are extremely important production equipment used in the production of aluminum extruded shapes. Presezzi Extrusion offers not only the front-loading extrusion presses that are globally mainstream but also extrusion presses equipped with the standard "E.S.S. (Energy Saving System)" that provides high rigidity, top quality, and energy savings. With numerous achievements as production equipment worldwide, it is an excellent extrusion press that can contribute to our customers' energy savings. *For more details, please refer to the PDF materials or feel free to contact us.

• Extrusion Machine

Presezzi Extrusion is the only manufacturer in the world that can consistently propose and produce a full extrusion line centered around extrusion presses. Since we can accommodate the entire full line of aluminum extrusion profiles, we are able to provide high-quality, cutting-edge, and energy-efficient production equipment. Here, we would like to introduce a video showcasing the full extrusion line as a testament to Presezzi Extrusion's achievements. *For details on each product, please refer to the catalog or feel free to contact us.*

• Other processing machines

Presezzi Extrusion is a manufacturer capable of supporting the entire extrusion "full line," centered around extrusion presses. Billet heaters are important equipment used as a pre-process for extrusion presses when producing aluminum extruded shapes. At Presezzi Extrusion, instead of the conventionally widely used coil-type induction heating, we use permanent magnets in the heating section, referred to as the "section," to heat the billets through the magnetic field generated by the rotation of the permanent magnet section. We have numerous achievements worldwide as production equipment and offer an excellent billet heater that can contribute to energy savings for our customers. It is patented and we hold the patent. *For more details, please refer to the PDF document or feel free to contact us.

• Extrusion Machine

In recent years, the electrification of automobiles (EVs) has been advancing. Since they do not use an engine, they do not emit carbon dioxide while driving, making them top-class in environmental performance among eco-cars. In this context, SincoTec has a wealth of experience in fatigue testing for various EV components, primarily serving major automobile manufacturers in Europe. We would like to introduce our state-of-the-art fatigue testing machines from SincoTec. In addition to selling fatigue testing machines, we also undertake contract testing. *For more details, please refer to the PDF materials or feel free to contact us.*

• Testing Equipment and Devices

"Torsion Moment Fatigue Testing Machine 'POWER TORSION'" Testing Applications: Powertrain, Transmission, Drive Shaft, Crankshaft, Gearbox Strain Assemblies, etc. ■POWER TORSION (Resonance Type) - Energy-saving, high testing frequency load, short testing time - High precision crack detection - Resonance-driven testing system for fatigue strength analysis - Dynamic testing with average load selection - Torsion moment: up to ±30,000Nm ■POWER TORSION static (Electric Servo Type) - Electric servo-driven testing system for static failure testing - Maximum torque: up to ±8,000Nm ■POWER TORSION dynamic (Hydraulic Servo Type) - Hydraulic servo-driven testing system for operational load testing - Torsion moment: up to ±8,000Nm (static average load) up to ±4,000Nm (static load) - Large torsion angle: ±50° *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

The "Kiln Shell Laser" is a measurement tool used to check for deformation in rotary kilns, dryers, and other low-speed rotating cylinders. The shell of a rotary kiln is exposed to high temperatures, and in cases of overheating, the shell may deform. If deformation occurs, it becomes difficult to install the kiln and adversely affects its lifespan. By placing this tool at various positions along the kiln, it continuously measures the distance to the shell and records any deviations (changes in distance). 【Features】 ■ Non-contact tool ■ Can be placed at various positions along the kiln ■ Continuously measures the distance to the shell and records deviations ■ When combined with the "Rotation Trigger" (optional), it can measure and record the rotational position relative to the kiln on a PC *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Kiln Axis Alignment System" is a rotary kiln measurement tool designed to verify the straightness of the kiln axis. Checking the alignment of the kiln axis is one of the most important measurements for rotary kilns and dryers that have two or more supports (kiln supports). The straightness of the kiln axis must be within strict tolerances to minimize stress on the kiln shell and to properly distribute support loads to the supports. With a combination of a theodolite, software, and a unique accessory kit, measurements can be easily taken without special surveying knowledge. 【Features】 ■ Easy measurement whether the kiln is operating or stopped (independent measurement) ■ No specialized surveying knowledge required ■ Measurements can be taken quickly and easily; approximately half a day for 2-3 supports ■ No need to measure roller and tire diameters *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

Fatigue testing machines for automobiles, railways, aviation, universities, and research institutions! Would you like to shorten your research and development time with the high-precision resonant fatigue testing machine "POWER SWING," which utilizes the principle of resonance? Moreover, not only in production equipment but also in testing machines, the rising electricity costs are increasingly burdening the running costs. The SincoTec resonant fatigue testing machine is highly effective for energy saving. Supports tensile, compression, rotation, bending, twisting, and internal pressure fatigue testing: ✓ Reduced testing time and energy saving ✓ High-frequency loading with low energy consumption due to resonance ✓ High-precision detection of micro-cracks as small as 10μm ✓ No hydraulic mechanism in resonant systems = no worries about oil leaks ✓ The MOT (motor-driven) resonant drive system is unique to SincoTec worldwide Of course, we can also accommodate hydraulic servo and electric servo systems depending on the testing conditions. *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

The "POWER SWING series" is a resonance-type fatigue testing machine that applies repeated loads based on the principle of resonance. We offer two types: - Motor-driven (MOT) system with a load range of 1kN to 2000kN and a testing frequency of 30 to 120Hz - Electromagnetic-driven (MAG) system with a load range of 5kN to 550kN and a testing frequency of 30 to 500Hz Starting with the cost-effective "POWER SWING" series, we have a wide variety of options suitable for testing parts and material samples. 【POWER SWING Features】 - Fast testing, energy-efficient, high-precision crack detection - Significant reduction in testing costs - Sturdy and high quality - Rated load: 1 to 2,000kN, high testing frequency: 30 to 500Hz - No hydraulic unit required = no worry about oil leaks - Proprietary software: EMOTION Customization for specific part applications is also possible. *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

The "POWER SWING MOT (Motor Driven) Series" is a resonance-type fatigue testing machine for materials and components with a test load range of 1 to 2000 kN. The test frequency ranges from 30 to 120 Hz, with a maximum amplitude of 12 mm. It is particularly suitable for material and component testing, especially for tests that require clearance. It is also suitable for low cycle fatigue (LCF) testing. 【Mechanism of the MOT (Motor Driven) System】 ■ Operates at frequencies below the resonance peak ■ Changes primary excitation based on the square of the drive speed ■ Varies the excitation frequency to change the amplitude ■ Adjusts the output amplitude using the excitation frequency *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

The POWER SWING MAG (Electromagnetic Drive) series is a resonant fatigue testing machine suitable for material test specimens and axial test specimens. The test load ranges from 5 to 550 kN, with a maximum amplitude of 6 mm. It is a system suitable for ultra-high cycle fatigue (VHCF) testing. Please feel free to consult us regarding testing methods, conditions, and objectives. 【Mechanism of MAG (Electromagnetic Drive)】 ■ Operates at the system's resonant frequency at all times ■ Amplifies to the maximum ■ Controls the output amplitude by varying the excitation frequency ■ Excitation frequency *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

The "POWER SWING MOT Internal Pressure" is an internal pressure load fatigue testing machine with a maximum pressure of 3000 bar (300 MPa). The rated load is 100 kN and 400 kN, with a maximum testing frequency of 40 Hz. We use our proprietary control software "EMOTION." Additionally, it is possible to add environmental condition simulations such as vibration excitation and temperature environments. 【Advantages】 ■ Capable of manufacturing internal pressure load testing machines up to 4000 bar (400 MPa) ■ Significantly more energy-efficient than hydraulic systems - Energy consumption: 4 kW for high-frequency loads (depending on testing conditions, etc.) ■ Can inspect internal pressure resistance in the shortest time possible ■ Environmental condition operation simulations can be added (vibration excitation, temperature environments, etc.) *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

The "POWER ROTATING BENDING" is a rotating bending testing machine with a bending moment range of 2,000 to 350,000 Nm. The testing frequency is 10 to 80 Hz. We use our self-developed control software "EMOTION." Additionally, with the built-in calibration device, static-dynamic comparative measurements can be easily performed. 【Advantages】 ■ Energy-efficient and fast testing ■ Visualization of technical cracks ■ Real load control of maximum strain amplitude ■ Easy static-dynamic comparative measurements with the built-in calibration device ■ Testing according to DIN EN 13260, 13261, 13262 (for railway use) *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

■Twist Testing Machine 'POWER TORSION' 〈Features〉 　✓ Resonance type (electromagnetic drive) twist fatigue testing machine 　✓ Rated load: up to ±6,000Nm 　✓ Testing frequency: 10 to 60Hz 　✓ Maximum twist angle up to ±22.5° < Advantages> 　✓ Average load selectable with or without 　✓ Twisting load with tensile R ratio possible 　✓ Static torsion testing possible 　✓ Winding moment possible 　✓ Torsion moment up to 20,000Nm also possible Additionally, we also offer a two-axis (twist and bend) testing machine 'POWER TORBEN' with a testing frequency of 100Hz, torsion moments of 6kNm, 40kNm, 400kNm, and bending moments of 4kNm, 20kNm, 200kNm. *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

"POWER ROTORQUE" is a fatigue testing machine that combines resonance and electric servo systems. It can handle radial loads of up to 100 kN. The torsional acceleration is ±6°, and the testing frequency goes up to 60 Hz. It also uses our proprietary control software "EMOTION." 【Advantages】 ■ Rotational testing with superimpose function, high-frequency radial and torsional amplitudes ■ Combination of radial load + alternating torsional amplitude (asynchronous operation) ■ Combination of 4-point bending + alternating torsional load (asynchronous and synchronous operation) ■ Radial load / axial load up to 1 MN: 20 kN ■ Radial frequency / torsional frequency up to 60 Hz: 25 Hz ■ Option: Oil conditioning *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

"POWER SPRING" is a spring testing system compatible with various types of springs. It uses our proprietary control software "EMOTION." We offer "POWER AXLE SPRING" for vehicle springs, "POWER INDUSTRIAL SPRING" for industrial springs, and "POWER BOW SPRING" for leaf springs. 【Features】 ■ Resonance-type fatigue testing machine ■ Compatible with various springs ■ Uses our proprietary control software "EMOTION" *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

The SincoTec fatigue testing machine can conduct high-precision tests with high test loads and high test frequencies for compression/tension, torsion, bending, rotation, and internal pressure testing. Its most notable feature, the "resonance-type" fatigue testing machine, is a top manufacturer in the world and is known for its time-saving, energy-efficient, and high-precision testing capabilities. The advantages of the resonance type are as follows: 1. Resonance type: Motor-driven (MOT) type, electromagnetic-driven (MAG) type / dynamic and static testing * The MOT method is unique to SincoTec in the world and is patented. 2. High precision detection of micro-cracks as small as 10μm using proprietary control software. 3. High test loads (1 to 2000 kN) and high test frequencies (standard 300 Hz, maximum 1100 Hz). 4. Compared to hydraulic systems, testing time is reduced by up to 1/10 and testing costs by up to 1/20. 5. Simple structure with low maintenance. No worries about oil leaks due to the absence of hydraulic mechanisms. No need to regularly replace consumables such as hydraulic oil and oil filters. 6. Over 30 years of experience with more than 4,000 units sold worldwide. 7. Custom machine production is possible according to customer requests. Hydraulic, electric, and compression testing machines are also available.

• Testing Equipment and Devices

Sinco Tec is a manufacturer of testing machines for parts and materials for the automotive, railway, wind power, and aerospace industries. "SincoTec Test Systems" develops and sells standard testing machines such as resonance, hydraulic servo, electric servo, and compression servo, as well as custom testing machines for various industrial sectors including automotive, railway, wind, and medical fields. In addition to the resonance testing machine "POWER SWING" series, we provide a wide range of customized testing machines and load frames with different drive systems. 【Business Overview】 ■ Development and sales of standard testing machines such as resonance, hydraulic servo, electric servo, and compression servo, as well as custom testing machines. *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

The RUF briquette machine, manufactured by the German company RUF, has been in operation for over 50 years and is used worldwide, with over 5,000 units in active service, as an efficient method for processing cutting chips and wood chips. In Japan, our company, Nittetsu Bussan Matex, serves as the general distributor, handling design, sales, installation, maintenance, and parts sales to keep the equipment in optimal condition on a daily basis. The 'RUF4/2300/60S' is a briquette machine (chip compression solidifier) that efficiently processes grinding sludge. It comes standard with a grinding oil recovery oil pan and a suction pump for discharging grinding oil, allowing for immediate use with just a power supply. Additionally, the standard briquette discharge rail enables the automatic transport of briquettes without the need for a briquette conveyor to transfer them to the briquette receiving box, allowing for direct input. 【Features】 ■ Efficient processing of grinding sludge ■ High oil removal rate for grinding oil and coolant ■ All-in-one structure ■ Centralized control via a touch panel *For more details, please refer to the documentation or feel free to contact us.

• Hydraulic Equipment
• others

The "Ovality Sensor" is a rotary kiln measurement tool that measures the changes in roundness/curvature, which are periodic elastic deformations of the operating kiln shell. This elastic deformation is referred to as ovality and primarily occurs near the kiln tires. This measurement provides accurate information regarding the mechanical load on the kiln shell, allowing for proactive measures to extend the kiln's lifespan. 【Features】 ■ Can measure while the kiln is operating (hot) ■ Lightweight handheld size *Sensor: approximately 1.5 kg ■ Compact design allows it to pass through the space between the rollers and the shell in most cases ■ Comes with a long-range Bluetooth adapter *For more details, please refer to the PDF document or feel free to contact us.

• Other measurement, recording and measuring instruments

◇ What is "hiTRAN"? 1. Wire elements intricately woven are inserted into the tubes of the heat exchanger. 2. Various wire materials such as SUS and copper can be used. 3. Compatible diameters: φ6 to φ150mm. 4. Applicable to both "existing" and "new" heat exchangers. 5. Appropriate shapes and densities are selected according to specification conditions. ◇ What are the benefits of "hiTRAN"? 1. Miniaturization of new heat exchangers (e.g., from 4 to 1 pass) ⇒ Reduction in initial costs! 2. Recovery of capacity in existing heat exchangers ⇒ Reduction in running costs! 3. Prevention and reduction of dirt inside the heat exchanger tubes ⇒ Reduction in maintenance costs and shutdown time! 4. Improvement of plant operational capacity ⇒ Reduction in utility costs!

• Other machine elements

The "resonance testing machine" vibrates a spring-mass system. It consists of two or three mass oscillators and proposes combinations of axial, torsional, bending, internal pressure, and rotational bending load systems. All systems are common, and the test specimen is unified as the spring of the oscillation system, applying high-precision, high-frequency loads. Additionally, tests using the resonance testing system are particularly beneficial as a precise final test due to their high energy efficiency and high-precision crack detection. 【Characteristics】 ■ High energy efficiency ■ High-precision crack detection (damage progression observation) ■ High force up to 2,000 kN or moment up to 400,000 Nm ■ Short testing time (due to high testing frequency, reduction of testing time during fatigue tests) ■ Only requires power connection *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

The hydraulic servo testing system is a load-driven testing system that applies load to the test specimen using a hydraulic servo testing cylinder. It can apply load in a uniaxial or multiaxial manner, and like for internal pressure, it is possible to set axial, torsional, and bending loads. It is extremely suitable for single-stage testing, similar to dynamic simulation testing, and in addition, these testing systems are also suitable for softer, elastic components, as well as multiaxial and phase-synchronized testing. 【Features】 ■ High load capacity ■ Multiaxial testing capability ■ Freely configurable load profiles ■ Simulation testing ■ Wide range of displacement amplitudes ■ Load and displacement control *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

The electric servo-type testing machine is controlled by a system of linear motion generated by a servo motor through spindle drive or electric servo method. The torque generated is recorded using additional linear guides by converting motor rotation into spindle drive. Additionally, the servo drive is controlled by a "TestPilot" controller that displaces the control using a test frequency of 0.001 to 50 Hz to operate or control the applied load. 【Features】 ■ Simple quality tool ■ Multi-axis testing capability ■ High mechanical rigidity ■ Average load ■ Accurate displacement control ■ Only requires power connection *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

The compression servo testing system generates test loads using a return compression cylinder. Many companies already have pneumatic systems in-house, making it easy and cost-effective to set up with this compression drive. SincoTec's compression unit, which includes all necessary components, is a very compact system that also incorporates proportional flow direction control valves and safety valves, in addition to the compression cylinder and load/displacement sensors. 【Features】 ■ Multi-axis testing capability ■ Large displacement amplitude ■ High reliability ■ Low investment cost ■ Easy system setup *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

We would like to introduce examples of achievements using the electric and hydraulic servo fatigue testing machines manufactured by SincoTec. Starting with the "2-axis steering column testing machine" capable of dual rotary drive, we also have numerous achievements including the "3-axis testing machine for composite leaf springs" with flexible adjustments, as well as the "4-point rotational bending testing machine" and "stabilizer testing machine/spring testing machine." In the PDF document below, we also introduce a wide range of other products, so please take a look. 【Examples of Achievements (Partial)】 ■ 2-axis testing machine ■ 3-axis testing machine ■ 4-point rotational bending testing machine ■ Multi-axis hydraulic testing machine *For more details, please refer to the PDF document or feel free to contact us.

• Testing Equipment and Devices

We would like to introduce our electric servo and hydraulic servo testing machines, 'POWER FLOW/POWER DRIVE.' In particular, we offer products such as the "POWER DRIVE direct-drive specification" for micro movements, the one-axis "POWER DRIVE" with direct drive spindle actuators, and the flexible mechanism "POWER DRIVE multi axial." Additionally, we also provide the "POWER FLOW Biaxial" with an axial load of 125kN. 【Product Lineup】 ■ POWER DRIVE direct-drive specification ■ POWER DRIVE ■ POWER DRIVE multi axial ■ POWER DRIVE torsion ■ POWER FLOW Biaxial *For more details, please refer to the PDF materials or feel free to contact us.

• Testing Equipment and Devices

Nippon Steel & Sumitomo Metal Corporation Matex is the exclusive distributor in Japan for fatigue testing machines manufactured by SincoTec (Germany). The resonance principle reduces testing costs by up to 1/20. With our self-developed control software "EMOTION," we can detect micro-cracks as small as 10μm with high precision. Please feel free to consult us regarding testing methods, conditions, and purposes. 【Features】 ■ Testing time reduced by up to 1/10 ■ High precision detection of micro-cracks as small as 10μm ■ Testing frequency: standard 300Hz, maximum 1100Hz ■ Testing costs reduced by up to 1/20 ■ No hydraulic mechanism, so no worries about oil leaks! Low maintenance ■ Suitable proposals from motor-driven (MOT) to electromagnetic-driven (MAG) based on application *For more details, please refer to the PDF document or feel free to contact us. *During the exhibition period, we will also showcase a demo machine for small test specimens. We look forward to your visit.

• Testing Equipment and Devices