サンハヤト List of Products and Services

The "Relay Cleaner NF RCF-S200" is a fast-drying contact cleaning agent that balances non-flammability and environmental considerations (global warming and ozone layer depletion). 【Features】 - Easily washes away oils, greases, and carbon deposits from relay contacts, slide contacts, connectors, plugs, etc., improving conductivity. - Excellent cleaning power against silicone oil and silicone grease. - Not subject to the Fluorocarbon Emission Control Law. - Not subject to the Fire Service Act, Organic Solvent Poisoning Prevention Regulations, or the PRTR Law. With excellent drying properties, it enhances work efficiency and allows for safe operation without the worry of ignition due to its non-flammable nature. Additionally, it achieves excellent cleaning power without using chlorine-based or bromine-based solvents, quickly dissolving and removing organic contaminants such as oils and greases. *For more details, please contact us or download the PDF materials for review.

• Cleaning agents
• Hand cleaner
• Other cleaning machines

The "ZE Blow JBE-S300" powerfully blows away dust and other debris attached to OA equipment, AV equipment, and other electronic devices. 【Features】 - The ozone depletion potential is virtually zero, meaning it does not harm the ozone layer, and its global warming potential is lower than that of CO2, resulting in minimal impact on global warming. - It is classified as a non-flammable gas under GHS and is also categorized as a non-combustible gas by the United Nations. It remains non-flammable below 28°C and only shows flammability above 30°C if exposed to open flames or significant ignition sources. - The risk of fire in typical usage environments is extremely low. - It features a trigger-type slim can that is easy to hold with one hand, enhancing usability. - It complies with the Green Purchasing Law. - It can be used with the "Ionizer Blow Gun BG-221R." *For more details, please contact us or download the PDF document for further information.

• Other PCs and OA equipment
• Other cleaning tools
• Office supplies and stationery

The "Spray-Type Compact Etching Device" is a tabletop-sized device for etching processes, such as those used for printed circuit boards, as well as for developing processes. It uses the chemical reaction of etching solution (ferric chloride) to etch (chemically corrode, engrave) copper foil according to the circuit pattern. By replacing manual tasks with the spray-type compact etching device, reproducibility improves and work efficiency increases! It has also been used for etching during printing on films, making it versatile for various applications! 【Features】 - Simple processing by just inserting the substrate due to the conveyor transport method - Spray (single-sided) type allows for high-quality substrates in a short time - Recommended for small-scale etching for experiments and prototypes - Supports work sizes up to 150×200mm - Compact type that can be placed on a desk for use By using the optional dedicated exhaust treatment cover (MODEL ES-400FC), it can be connected to exhaust devices such as Sunhayato's ES-F2 and KS-8. *For more details, please contact us or download the PDF materials for further information.

• Printed Circuit Board
• Circuit board processing machine
• Other semiconductor manufacturing equipment

The "MDP-10" is a printer that can directly print high-resolution etching resist onto copper foil boards. It has a built-in UV irradiation device that cures the ink simultaneously with printing. The printed etching resist can be removed using a dedicated stripping solution after etching. It is compact and lightweight, making it suitable for desktop use. It supports printing up to A4 size. 【Features】 ■ Uses UV-curable ink ■ Capable of printing up to A4 size ■ Compact and lightweight desktop type ■ High resolution of 1440dpi x 1440dpi ■ Comes with dedicated software *For more details, please request documentation or view the PDF data available for download.

• others
• Printed Circuit Board

This is a product set that includes QP screens and QP frames, allowing anyone to easily perform screen printing. The screen mesh is #225, and the frame is made of durable aluminum, making it ideal for prototype circuit boards and small-scale production.

• Other work tools
• Other markings
• Prototype Services

Prototype hand-operated tabletop printing machine for small-scale production.

• Other work tools
• Other markings
• Prototype Services

By cleaning with this product, the adhesion between the copper foil surface of the printed circuit board and the resist is improved.

• Printed Circuit Board

LED stick circuit board UB-LED001 (5-series parallel connection type) UB-LED002 (3-series series connection type)

• Printed Circuit Board

The best partner for a breadboard: Breadboard accessories jump wire kit.

• Printed Circuit Board

This product is a set of components necessary for constructing the circuits introduced in the book "Fun and Easy Breadboard Electronics" published by the Tokyo Denki University Press.

• Printed Circuit Board

It is a double-sided land, but there are no through holes. It is possible to increase the mounting density.

• Printed Circuit Board

The connector position is aligned with the Arduino, so it can be attached to the Arduino without any misalignment.

• Printed Circuit Board

This is a PIC microcontroller board for experimentation and evaluation compatible with the PIC16F/18F series.

• Printed Circuit Board

It is equipped with a USB mini-B type connector.

• Printed Circuit Board

Please note that the scale of the pattern diagram is not constant.

• Printed Circuit Board

Please note that the scale of the pattern diagram is not constant.

• Printed Circuit Board

Since it uses a conveyor transport system, it's a simple process of just inserting the circuit board.

• Printed Circuit Board

Prototype circuit check and operation confirmation → New breadboard

• Printed Circuit Board

An adapter that converts to allow writing with a universal ROM writer.

• Other electronic parts

An adapter for converting to be used on a universal board.

• Other electronic parts

DIP width conversion adapter

• Other electronic parts

An adapter that converts various packages for use on a universal board.

• Other electronic parts

LED spacer that achieves high reliability in soldering and cleaning processes.

• Other electronic parts

A small terminal for attaching wires that can be placed anywhere, making pattern design easy.

• Other electronic parts

Terminal for mounting adjustment parts that does not allow the soldering iron to directly touch the circuit board during component replacement, preventing damage to the board.

• Other electronic parts

This is an introduction to the Teflon terminals handled by Sanhayato.

• Other electronic parts

A terminal for hybrid IC production that can serve as both a spacer and a signal line when mounted on a sub-board.

• Other electronic parts

A block for vertical mounting of the substrate that allows easy fixation of the display board to the main substrate.

• Other electronic parts

Screwless terminal block that can be directly mounted on a circuit board with a 2.54mm pitch.

• Other electronic parts

This is an introduction to the one-touch connector terminals handled by Sanhayato.

• Other electronic parts

A terminal that can relay four components in one location.

• Other electronic parts

A terminal for line correction and checking that allows for reliable signal extraction and easy removal after checking.

• Other electronic parts

A terminal for circuit shorting that allows for easy switching of board patterns when combined with 0.635mm wrapping terminals and 2.54mm pitch pin headers.

• Other electronic parts

A check terminal that can also be used as a check terminal in addition to wrapping, for wrapping purposes.

• Other electronic parts

Wrap terminals with excellent workability that can be fixed at the same height with a click.

• Other electronic parts

Check terminals for wrapping, featuring a stopper for excellent workability.

• Other electronic parts

Check terminal for logic that can be mounted on a screw hole.

• Other electronic parts

A check terminal for surface mounting that can securely clip and easily extract signals.

• Other electronic parts

Surface mount check terminals with the same size as 1/8 inch square chip resistors, featuring simple pattern design.

• Other electronic parts

Check terminal that can be hooked from all directions by the oscilloscope probe.

• Other electronic parts

This is an introduction to the universal board for ISA bus handled by Sanhayato.

• Printed Circuit Board

Connector conversion board that extracts various connector pins into a 2.54mm pitch dot pattern.

• Printed Circuit Board

A board that draws out the pins of the SOP package IC to a dot pattern with a 2.54mm pitch.

• Printed Circuit Board

A QFP IC conversion board that solders an IC in the center of the substrate and draws wiring from the surrounding lands.

• Printed Circuit Board

This is an introduction to the LED flash circuit boards handled by Sanhayato.

• Printed Circuit Board