Please hurry! There are only "16 months" left until the deadline for low-concentration PCB disposal.

High-frequency oscillator that integrates the latest technology.

The "FOCUS," a transistor inverter developed in-house by Fuji Electronic Industries, is a source of pride. With a single oscillator, it is possible to change the frequency for hardening. Due to parallel resonance, variations in quality caused by load fluctuations can be minimized. We are committed not only to improving production efficiency and quality but also to proposing environmentally friendly production systems that focus on energy conservation, cost reduction, and CO2 emission reduction. <Here are some testimonials from customers who have switched from vacuum tube oscillators to transistor oscillators.> Customer A: I thought it was a lie, but my electricity bill really became about half, and I was praised by the president! Customer B: It's great that I can still use the coils I was using before; nothing went to waste. Customer C: The installation area has been significantly reduced, and it looks neat!! ★ For inquiries by phone, please contact us here: Osaka Headquarters → TEL: 072-991-1361 Nagoya → TEL: 052-322-1361 Tokyo → TEL: 03-5472-1361 *When calling, please mention that you saw it on "Ipros." Response hours: Monday to Friday, from 9 AM to 5 PM.

• power supply

Insulating oil from old electrical equipment that has been in use for over 30 years may be contaminated with PCBs. Proper disposal is required by the disposal deadline. If you are using a vacuum tube oscillator, please check! - Transformers - Capacitors - Rectifiers, etc. Please consider updating any relevant equipment such as oscillators and hardening equipment as soon as possible. *For more details, please refer to the PDF document or feel free to contact us. ★ For inquiries by phone, please call: Osaka Headquarters → TEL: 072-991-1361 Nagoya → TEL: 052-322-1361 Tokyo → TEL: 03-5472-1361 ★ For inquiries by email, please contact: info@fujidenshi.co.jp *When calling or emailing, please mention that you saw this on "Ipros." Response hours: Monday to Friday, 9 AM to 5 PM.

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If you require a detailed technical explanation, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without affecting the base material with heat. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.