An article about ultrasonic cleaning devices was published in the January issue of 【Sonosys】 Interface.

Leave the latest ultrasonic cleaning to Sonosys.

Ultrasonic Cleaning Spray Nozzle For non-contact single substrate cleaning, we offer a megasonic nozzle with either a single nozzle, dual nozzle, or triple channel, and any combination of frequencies ranging from 600kHz to a maximum of 9MHz. The transducer of this megasonic nozzle generates megasonics and sends them through a fluid (such as pure water) to clean the surface of the substrate. Megasonic Immersion Transducer This is a megasonic immersion transducer with frequencies of 400kHz, 600kHz, 1MHz, and 2MHz. A sealed transducer made of stainless steel or plastic (e.g., PP, PVDF, or PFA) is installed at the bottom or side of an existing tank. In addition to standard systems for substrate sizes of 4", 6", and 8", custom immersion transducers are also available. The highly adaptable configuration allows the megasonic system to be used in bath-tank cleaning processes, improving cost-effectiveness. Frequencies available are 400kHz, 600kHz, 1MHz, and 2MHz.

• Ultrasonic Oscillator
• Other cleaning machines
• Ultrasonic Cleaner

A collaborative product of Rehila's nozzle technology and Sonosys's ultrasonic technology.

Particles (droplets) formed by the ultrasonic spray nozzle are broken up by the vibrations of the piezo element. In other words, unlike pressurized systems, the particles do not have speed. As a result, they either fall naturally or float due to the influence of the wind. Therefore, carrier air is used to transport the formed particles for application.

• Ultrasonic Oscillator
• nozzle
• Coating Machine

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.