Announcement of the release of the new product: Multi-channel microcurrent measurement device "PCM Series".

Leak tester for electronic components such as semiconductors, capacitors, and resistors! Contributes to reduced inspection time and cost savings with simultaneous measurement of up to 300 channels of microcurrent!

The PCM series is a multi-channel microcurrent measurement device that can simultaneously measure minute leakage currents and consumption currents across multiple channels. Since each channel operates independently, multi-channel simultaneous measurement can be performed without relay switching. This significantly shortens the measurement cycle in inspection and evaluation processes, contributing to improved throughput and reduced equipment costs. The measurement range is from 0.00nA to 999.99nA, with a resolution of 0.01nA, allowing for stable measurement of minute leakage currents and consumption currents. It also has a built-in DC voltage output function, enabling voltage application and current measurement to be completed with a single device. With a rich lineup ranging from 25 channels to a maximum of 300 channels, it can accommodate a wide range of applications from small-scale evaluations to mass production inspections. It comes standard with a dedicated automatic measurement application, allowing for immediate operation after installation. Furthermore, it can flexibly accommodate customizations based on the measurement targets and inspection contents.

• Ammeter

● This is a leak testing device for small electronic components that does not use fluorinated inert liquids (PFAS-free). ● There is no longer a need for unstable visual confirmation through liquid immersion testing. It adopts a quantitative testing method that allows for stable pressure leak testing. ● It is a tabletop leak testing device specifically for gross leaks, with accuracy equal to or greater than that of liquid immersion testing. ● The detectable range is approximately 1×10⁻² Pa·m³/s to 1×10⁻⁶ Pa·m³/s (varies depending on the target product). ● It is suitable for sealed structures ranging from a few millimeters to a maximum of 80 × 70 mm. Please feel free to contact us for more information!

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact on the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! With one molding process, different products with similar shapes or varying dimensions can be molded at the same time. This allows for the verification of multiple types in a short period.