We have compiled a list of manufacturers, distributors, product information, reference prices, and rankings for Broad Disc.
ipros is IPROS GMS ・ IPROS One of the largest technical database sites in Japan that collects information on.

Broad Disc - List of Manufacturers, Suppliers, Companies and Products | IPROS GMS

Broad Disc Product List

91～120 item / All 134 items

Displayed results
Example of installation in a resin powder storage bunker.

Example of installation in a resin powder storage bunker.

Introducing examples of continued adoption by resin material manufacturing companies.

At the resin raw material manufacturing company, to promote discharge from the bunker, a "blow disk" was adopted near the discharge outlet located at the bottom of the silo (conical part, midway). This time, we were consulted about installing this equipment in the area opposite the discharge outlet, as the powder there was not moving and was piling up like a mountain, in order to effectively utilize the bunker’s volume. We communicated that completely eliminating the pile was difficult and presented a proposal for installation. It was later decided to implement the solution, and the results have improved to a level acceptable to the customer. [Overview] ■ Material: Resin powder (prone to clumping) ■ Bunker capacity: 200m3 * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0301 Aeration in the chlorine dust silo

0301 Aeration in the chlorine dust silo

Introducing a case of a Brody disk adopted to promote chlorine dust emission in silos.

This is an introduction to a case where the "Blow Disc" was adopted for aeration to promote the emission of chlorine dust in a silo. The model used this time is the BD-25 type, which is for use with a Roots blower, rather than the standard BD-15 Blow Disc for compressed air. The "Blow Disc" is available in a type that can be used not only with compressor air but also with a Roots blower. 【Overview】 ■ User Industry: Cement ■ Target Material: Chlorine Dust ■ Silo Diameter: 3000φ ■ Blow Disc Overview ・ Model: BD-25S-B (for Roots Blower) ・ Quantity and Installation Situation: 16 units... installed in 4 on the lower level, 4 on the middle level, and 8 on the upper level. * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous implementation examples, which can be checked via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Adopted for equipment for pharmaceutical manufacturers.

Adopted for equipment for pharmaceutical manufacturers.

Case of Brody Disk Adopted for Solving Very Poor Fluidity Powder Bridge Issues

This is an order received from a business that manufactures hoppers and transport equipment, as specified by the end user (pharmaceutical manufacturer). The business was concerned about bridging during the hopper design due to the very poor flowability of the material (which resembles potato starch and has strong adhesion). Upon consulting with the user, it was decided to install this equipment effectively, as the user had already had experience using a BroaDisk. 【Overview of Usage Conditions】 ■ Hopper dimensions: 400×700 ■ BroaDisk arrangement: 2 BroaDisk Minis on the lower level, 2 BroaDisks on the upper level ■ Operating method (sequence): 1) Turn on both BroaDisk Minis on the lower level simultaneously 2) Turn on one BroaDisk on the upper level 3) Turn on the remaining BroaDisk on the upper level * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies, which can be accessed via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0099 Measures to prevent clogging of wet powder from the centrifuge

0099 Measures to prevent clogging of wet powder from the centrifuge

Case study of a blow disk adopted as a countermeasure for wet powder clogging from a centrifuge.

We introduce an example of a Brody disk that solved the clogging of dewatered cake in a vertical chute connecting a decanter-type continuous centrifuge and a subsequent dryer. The Brody disk is primarily used to address blockages and bridge rat hole phenomena in powdery materials (dry), but there are cases where it has completely resolved user issues by being used with wet powder (cake) as in this instance. Of course, not all issues are resolved, but there are cases where problems can be easily solved depending on the conditions. 【Chute Overview】 <Clogging Section> ■ Shape: Square/Round Chute ■ Dimensions: Upper 400×500, Lower 300φ, Height 300 *For more details, please refer to the PDF document or feel free to contact us. We have published numerous examples on our company website. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0116 Elimination of fine powder retention in toner manufacturing equipment and dust collector hopper.

0116 Elimination of fine powder retention in toner manufacturing equipment and dust collector hopper.

A case where the fine powder retention in the dust collector hopper of toner manufacturing equipment was resolved using a blow disc.

Jet milling - Elimination of toner fine powder residue in the dust collector hopper section of the toner manufacturing plant through air classification. Due to the very fine dust generated by fine milling and fine classification, the air knocker was not effectively preventing retention. Although it is a large hopper, eight blow discs were installed relatively close to the discharge section, and it is operating smoothly. The blow discs solve the rat hole and bridging phenomena in various powders and bulk silos and hoppers. They are easy to install and economical. 【Key Points of This Equipment】 ■ The elastic disc (silicone) is very important in terms of strength and durability, especially considering the risk of foreign matter contamination. The silicone discs of this equipment are exceptionally strong and durable. You will understand once you use it! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. * For more details, please refer to the PDF materials or feel free to contact us. * Our website features numerous case studies. You can check them through the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Improvement of discharge failure from the acrylic resin hopper.

Improvement of discharge failure from the acrylic resin hopper.

An example of improving the discharge failure from the acrylic resin hopper using a blow disk.

To improve the outflow and discharge issues from the hopper of fine acrylic resin powder, a blow disk has been installed. The powder has a low apparent specific gravity and small particle size, and before the countermeasure with the blow disk, it seemed to be clogging above the discharge rotary valve. After the countermeasure, it has stabilized and is now discharging properly. If you provide us with details about the powder (name, particle size, and other characteristics) and the hopper dimensions, we can guide you on the appropriate models and operating methods. Please feel free to contact us. 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign matter contamination. The silicone disk in our equipment is exceptionally strong and durable. We believe you will understand this once you use it! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please refer to the PDF materials or feel free to contact us. *Our website features numerous case studies, which you can check through the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0122 Bridge measures for jet mill ground products (color materials)

0122 Bridge measures for jet mill ground products (color materials)

Solve the bridging phenomenon of difficult-to-discharge colorant powders!

We would like to introduce a case study on bridge prevention measures for jet mill ground products (color materials). During the trial operation of the powder plant, a bridging phenomenon occurred in the product tank, making it difficult to discharge the color powder. The particle size of the powder is small (jet mill ground product), and it seems to be a very poorly flowing material. There are several types of blow discs, and it was determined that installing a larger number of the standard type (BD-15) would be better than installing the "BD-20 type," which has a higher air volume. The results were good, and the cost was also satisfactory. 【Key Points of This Equipment】 ■ The elastic disc (silicone) is very important in terms of the risk of foreign matter contamination, as strength and durability are crucial. The silicone disc of this equipment is extremely strong and durable. Once you use it, you will understand! ■ Control (how to aerate?) is important! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF materials or feel free to contact us. *Our website features numerous implementation examples, which can be checked via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0141 Prevention of bridge formation in water-repellent agent supply devices

0141 Prevention of bridge formation in water-repellent agent supply devices

Problems solved with aeration and vibration!

We would like to introduce a case where a blow disc was installed to prevent bridging in a water-repellent agent supply device (screw feeder). 【Overview】 ■ Hopper capacity: Approximately 1m³ ■ Details of the powder (water-repellent agent) - Unknown; initially attempted to address bridging with an air knocker, but it was ineffective. ■ Result - The problem was resolved through aeration and vibration using the blow disc. 【Key Points of This Equipment】 ■ The elastic disc (silicone) is very important in terms of strength and durability due to the risk of foreign material contamination. The silicone disc of this equipment is exceptionally strong and durable. Once you use it, you will understand! ■ Control (how to aerate) is crucial! We provide guidance on what should be done. A dedicated controller is also available. * For more details, please refer to the PDF materials or feel free to contact us. * Our website features numerous implementation examples, which can be checked via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0151 Rat Hole Measures - Chemical Material Manufacturer

0151 Rat Hole Measures - Chemical Material Manufacturer

Easily resolve troubles! We will propose installation examples and operating conditions that match the customer's requirements.

We would like to introduce a case of rat hole prevention at a chemical materials manufacturer. Normally, the powder does not pose significant issues and can be discharged from the hopper, but when it contains 3% moisture, its flowability deteriorates significantly. Traditionally, only vibrators were used, and for materials with high moisture content, in addition to the vibrations from the vibrator, air purging from a quick-connect fitting was employed. However, this did not completely eliminate the rat hole issue, leading to the introduction of our equipment, which easily resolved the challenge. [Overview] ■ Hopper Size: 1500×1500 ■ Installation Position: 2 units installed on each side (total of 8 units) * For details, please feel free to contact us. * For more information, please refer to the PDF materials or feel free to contact us. * Our website features numerous implementation examples, which can be checked via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0331 Target: With carbon black masterbatch

0331 Target: With carbon black masterbatch

The installation of the Brodisk has solved the problem of discharging powdered materials!

The facility manufacturing masterbatch has adopted the "Brodisk." Due to the hopper's slope being gentler than the material's angle of repose, there were difficulties in discharging the target powder. However, the installation of the Brodisk has resolved this issue. 【Overview of Usage Conditions】 ■Raw Materials - Carbon black - Particle size = under 50μm - Bulk density = approximately 0.15 - Angle of repose = approximately 45° ■Hopper Size - 1200×1200 ■Brodisk Arrangement - 3 units on each side, totaling 12 units installed ■Brodisk Operation - Controlled by a controller with 6 solenoid valves, the Brodisk is sequentially turned ON in groups of 2 at 6 locations. *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous case studies. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0348 Shortening the discharge time of corn feed.

0348 Shortening the discharge time of corn feed.

For solving problems such as rat hole bridges! Introducing case studies of Brodisk implementation.

There have been instances of rat holes occurring in the feed silo, and we have received inquiries about not being able to discharge within the specified time... We want to do something about it... As usual, we reviewed the silo diagram and proposed the arrangement of the blow disk, which was promptly implemented. After the installation of the equipment, we were able to discharge approximately 4 tons in a stable manner within about 10 minutes. There were constraints on the compressor capacity, but the customer adjusted the air pressure, air ON time, and air OFF time in various ways to find the minimum air consumption conditions. [Overview] ■ Material: Corn (powder + grains approximately 5mm) *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous implementation examples, which can be checked via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Elimination of the bridge in elastomer crushed products (powder).

Elimination of the bridge in elastomer crushed products (powder).

You can set the air ON/OFF time at will! Introducing case studies of Brodisk deliveries!

Here is an introduction to a case study on bridge prevention using a relatively small hopper. The material is said to be an elastomer powder, and from what I saw of the sample, it contained a significant amount of powder. Since a test was requested, we lent the necessary quantity of our equipment for the experiment. The results were as expected, and the bridge was resolved immediately. In this case, we installed one Brodie disk (BD-15) on each of the three inclined surfaces, for a total of three. The three disks are turned ON and OFF simultaneously using the controller (C-SV1). [Hopper Conditions] ■ Size: 200×500 ■ Shape: Three inclined surfaces, one vertical ■ Discharge: 40φ from the lower end of the vertical surface *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous case studies. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Elimination of the bridge caused by the repurposing of the feed tank.

Elimination of the bridge caused by the repurposing of the feed tank.

Introducing a case study on the implementation of a Brody disk for silo bridge prevention.

This is a case study on bridge issues in feed silos. We received an inquiry stating that a silo for crushed feed rice had started to experience bridging when repurposed for other feed types. The details of the new material are unclear, but previously, discharge was facilitated by vibrating plates. Based on related information, we provided guidance on the placement of our equipment, which was subsequently adopted. After the installation of our equipment, it has been evaluated that bridging no longer occurs. [Overview] ■ Silo diameter: 2500φ ■ Discharge diameter: 500φ (further narrowed below this) ■ Hopper section slope: 45° *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous case studies. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0370 Promotion of the outflow of titanium dioxide mixture

0370 Promotion of the outflow of titanium dioxide mixture

An example of installing a larger number of broad disks/broad disk minis to mitigate risks.

This is a consultation request from an engineering company. Due to the discharge diameter being 3S and relatively small, we installed two Bro-Disk Minis at different heights in this area, and four Bro-Disks on the circumference above, for a total of eight units. A key point this time is that the Bro-Disk Minis installed below have a lower air flow compared to the Bro-Disks, so we have conducted two consecutive air ON operations. After delivery, we received feedback stating, "The Bro-Disk Minis installed near the discharge area were absolutely necessary." [Overview] ■ Hopper diameter: 600φ ■ Discharge diameter: 3S *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous implementation examples, which can be checked through the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0376 Prevention of clogging in powdered activated carbon

0376 Prevention of clogging in powdered activated carbon

Introducing a case where a blow disk was installed in the powder activated carbon feeding hopper with two lines.

This is a case adopted by a facility primarily producing functional resin products. There are two lines with hoppers, and one line has a significantly small discharge diameter from the hopper, which increased the risk of bridging. After hearing the details, we provided a countermeasure proposal, which was immediately implemented. Since the installation of this equipment, we have received feedback that bridging and blockages have not occurred. 【Overview of Bro-Disk Arrangement】 ■ Line 1 - Four Bro-Disks arranged on the circumference 200-300mm above the discharge section ■ Line 2 - Four Bro-Disks arranged on the circumference 200-300mm above the discharge section - Four Mini Bro-Disks arranged on the circumference 100-200mm above the discharge section *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous implementation examples, which can be accessed via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
Resolving the bridge of resin powder (water-added)

Resolving the bridge of resin powder (water-added)

An example of installing a Brody disk to solve the problem of the bridge phenomenon occurring when water is added to resin powder.

This is an example we received from a manufacturer of labor-saving machinery. We were consulted because "the customer (in the chemical industry) started adding water to resin powder, and a bridging phenomenon that had not occurred before began to happen in the delivered equipment." The key point this time is that while the flowability of the resin powder before water addition is relatively good, the angle of repose increases due to the addition of water, and there is a possibility of increasing the amount of water added in the future. In this case, considering that the discharge diameter of the hopper is somewhat small at 100A and the worsening of the angle of repose due to increased water addition, we added four mini blow discs (BD-08) just above the 100A discharge section in addition to the four previously mentioned blow discs. After implementation, we followed up and there have been no troubles; it is operating smoothly. 【Overview】 ■ Product Name: Resin Powder ■ Particle Size: 10 to 1000 μm ■ Hopper Shape: Cone 1000φ ■ Discharge Diameter: 100A *For more details, please refer to the PDF materials or feel free to contact us. *Our website features many examples of implementations. You can check them from the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0397 Prevention of bridge formation of dust containing glass fibers

0397 Prevention of bridge formation of dust containing glass fibers

Prevention of dust containing glass fibers! An example of applying a blow disk to the hopper section of a dust collector.

This is a case where a blow disk was adopted for application to new equipment. The application location is the dust collector hopper section. Since the blow disk injects air along the inner surface of the hopper, it is generally the case that the effectiveness does not change significantly even if the installation position is slightly off. The key point this time is that due to the properties of the target material, the air pressure used is high, the air ON time is short, and air aeration is performed in a pulsed manner. [Overview] ■ Hopper approximate dimensions: 2000×2000 (discharge section 200×200) ■ Blow disk arrangement - 3 units per 4 sides, with 1 unit on the lower level and 2 units on the upper level per side (However, only 2 units are installed on one side due to the inspection port) - Both lower and upper levels are positioned quite low, near the discharge port * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous implementation examples. You can check them from the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0404 Measures against rat holes in catalyst raw materials

0404 Measures against rat holes in catalyst raw materials

A case where Brodisk was adopted repeatedly for the expansion of the line.

This is a repeat project that we have been hired for. This project was previously adopted a few years ago, and we received feedback from the user that "extremely good results were obtained." This time, we are being hired again for the expansion of a similar line. In this case, we were informed about the properties of the material measured with a powder tester. We would appreciate it if you could provide such data, but even if only the material sample and hopper diagram are provided, we can inform the customer about the optimal arrangement of our equipment based on that information. Please feel free to contact us. [Overview] ■ Trouble Situation - Rat hole in an 1800φ conical hopper - Discharge diameter is 200A, with a typical rat hole forming directly above the discharge section. ■ Material - Name: Confidential (catalyst raw material) - Particle size: Several micrometers - Angle of repose: Approximately 50° - Bulk density: Loose approximately 0.3 / Dense approximately 0.6 *For more details, please refer to the PDF document or feel free to contact us. *We have many examples published on our website. You can check them via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0411　サービスステーション（セメント）向けに納入

0411　サービスステーション（セメント）向けに納入

稼働後の状況はもちろん良好！　プラント設備工事業者様にご採用いただいた事例のご紹介です

SS向けの案件で、従来使用していた「〇〇レーション」というブリッジ防止機器が調達できないとのことで代替え用としてお問い合わせいただきました。 きっかけは、代替品としてのお問い合わせでしたが、ご使用条件などをもとに、当社ブローディスクの配置や設置方法についてお打合せを進めると、設置数量・機器コスト面・取付工事の面などでメリットが生まれることが判明。 稼働後の状況は、もちろん良好でユーザー様にもご満足いただいています。 【概要】 ■直径3800φサイロの下方に（今回はかなり下のほうのみです） 　4個×2段に配置 ■製品仕様：ブローディスク BD-15S-B 8個 ※詳しくはPDF資料をご覧いただくか、お気軽にお問い合わせ下さい。 ※当社ホームページに多数の実施例を掲載しています。 　下記リンクよりご確認いただけます。

  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0412 Measures to Prevent Clogging of Tapioca Flour

0412 Measures to Prevent Clogging of Tapioca Flour

The result is OK! This is a project that adopted the load disk (mini) and controller.

This is an introduction to a case where the powder did not drop at all from the hopper, and despite various attempts, nothing worked. Knockers and vibrators were not effective, and a homemade aeration system created by modifying the piping also had no effect. We received a call expressing interest in trying a blow disk. After discussing the situation and receiving examples of what did not work from the customer, we decided on the arrangement and quantity of our equipment, lent out product samples, and conducted a trial. The result was positive; the blockage was resolved, and the customer decided to adopt the blow disk (mini) and controller. [Overview] ■ Material: Tapioca flour (also corn starch) ■ Hopper diameter: 300φ ■ Discharge diameter: 100φ * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them out via the link below.

  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0419 Resolving blockages of crushed material + virgin raw materials

0419 Resolving blockages of crushed material + virgin raw materials

We have been evaluated as having resolved the issue of clogging, and you have adopted our equipment.

This is a case adopted by a business primarily engaged in the molding of resin products. When introducing a new hopper, the mixing ratio of crushed material and virgin material was changed, which led to the occurrence of bridging that had not happened with this material before. They contacted us expressing a desire to try the BroaDisk. After receiving information about the hopper and materials, we promptly decided to send a demo unit. After providing the ideal arrangement for the BroaDisk (mini), the user experimented with various air pressures and aeration times, and they evaluated that the issue of clogging was resolved, leading to the adoption of our equipment. 【Overview】 ■ Hopper diameter: Approximately 300φ ■ Discharge diameter: Approximately 30φ ■ Inclined section: More gentle than typical ones * For more details, please refer to the PDF materials or feel free to contact us. * Our website features numerous implementation examples. You can check them from the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0429 Promote the discharge of fly ash

0429 Promote the discharge of fly ash

We have adopted a blow disk to improve the emission defects occurring on the fly ash side!

This is an inquiry made through a trading company regarding an issue at an existing plant. A single round silo is divided into two sections by an internal partition, and this equipment was introduced to improve the discharge issues occurring on the fly ash side of one half. The plant originally had aeration nozzles installed, but since that was not effective, this equipment was adopted. After the introduction of this equipment, it has been operating without any problems. 【Overview of Blower Disk Installation】 ■ 8 standard blower disks installed in the silo section (Arranged in 3 tiers: 3 + 2 + 3) ■ 2 standard blower disks installed in the chute section (The chute section has sufficient slope, so 2 disks are installed at different heights) * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them out via the link below.

  • 2.png
  • 3.jpg
  • 4.png
  • Other powder equipment
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0443 Resolving the bridge of carbon-containing dust

0443 Resolving the bridge of carbon-containing dust

We are providing information about the installation locations and control examples of the Brodisk according to the customer's requirements!

We would like to introduce a case where this equipment was implemented to address bridging issues in a dust collector hopper for local exhaust ventilation. The dust being collected contains carbon, and there is a period when the original material is left outdoors in a bulk bag, which particularly absorbs moisture during rainy weather, leading to bridging. The bridging situation occurs right above the discharge device (rotary valve), where we installed four units, one on each side in this area. Additionally, we installed four more units slightly higher up (each positioned at the corners of the hopper to prevent retention in the four corners), bringing the total to eight units. 【Overview】 ■ Hopper size: approximately 2000×2000 ■ Discharge section: 200A *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous implementation examples, which can be checked via the link below.

  • Other processing machines
  • others
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0439 Attached to vehicle-mounted bag filter

0439 Attached to vehicle-mounted bag filter

Easily suppress bridges with the combined effect of aeration and the vibration of rubber discs!

We would like to introduce an example of our vehicle-mounted bag filter. Due to various constraints for vehicle use, it was reported that the repose angle of the hopper could not be sufficiently secured, leading to bridging issues. As a result of adopting our equipment as a countermeasure against bridging in the vehicle-mounted dust collector hopper, we achieved effective results and customer satisfaction. 【Overview】 ■ Hopper diameter: Approximately 1600Φ ■ Discharge diameter: 400Φ ■ Hopper repose angle: Approximately 55° ■ Target suction materials: Fly ash, etc. 【Key Points of Our Equipment】 ■ The elastic disc (silicone) is very important in terms of the risk of foreign matter contamination, as well as strength and durability. The silicone disc of our equipment excels in strength and durability. We believe you will understand this once you use it! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF materials or feel free to contact us. *Our website features numerous examples of implementations. You can check them via the link below.

  • Other processing machines
  • others
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0474 Elimination of bridges in high humidity sites.

0474 Elimination of bridges in high humidity sites.

Introducing a Brody disk for wastewater treatment facilities! Easily resolves bridges and rat holes.

When the humidity at the site increases, bridges frequently occur. Here, we would like to introduce a case where measures were taken to address this issue. Two Brody Disk Minis were installed opposite the square hopper, and a controller (C-SV1) with one solenoid valve was used to provide intermittent aeration for both units simultaneously. In general, for fine powders with poor fluidity, the air ON time is often set to around 3-5 seconds. However, in this case, 1-2 seconds yielded good results. 【Case Overview】 ■ Application: Wastewater treatment equipment ■ Target material: Bio-coagulant (similar to wood chips) ■ Hopper: Approximately 250 mm square 【Key Points of Our Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability due to the risk of foreign matter contamination. The silicone disk of our equipment excels in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0499 Installation on activated carbon and quicklime silos.

0499 Installation on activated carbon and quicklime silos.

Air aerators are important for placement! We will provide advice on selecting the appropriate model and planning the layout according to the conditions.

We would like to introduce a project requested by a client in the silo canning business. The end user expressed a desire to install our BroaDisk, and we received an inquiry from the silo contractor. It seemed that this representative had no experience with aeration or bridge breakers at all, so we decided to convey the basic concepts and considerations for this case before proceeding with the order. 【Case Overview】 ■ Activated Carbon Silo ・Diameter: φ2000 ・Capacity: 5m3 ・Equipment Configuration: 4 units × 2 tiers (Total 8 units) ■ Hydrated Lime Silo ・Diameter: φ3000 ・Capacity: 50m3 ・Equipment Configuration: 4 units × 3 tiers (Total 12 units) *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0514 Measures to prevent clogging of titanium dioxide

0514 Measures to prevent clogging of titanium dioxide

Easily solved with Brodisk! We will provide guidance on selecting models and arrangements that meet the user's requirements.

We would like to introduce a case where a user experiencing significant issues with the discharge of titanium oxide reached out to us. The size of the hopper in question is 500×500, and if the flowability of the powder is quite poor, it is generally recommended to use at least four blow discs (standard type: BD-15). Initially, four BD-20 type blow discs were adopted, and aeration was performed manually under various conditions. As a result, it was determined that it is preferable to sequentially turn on the air for each of the four blow discs with a time delay, and a controller (with four built-in solenoid valves) was adopted for this purpose. 【Key Points of This Equipment】 ■ The elastic disc (silicone) is very important in terms of strength and durability, especially considering the risk of foreign material contamination. The silicone discs in our equipment are exceptionally strong and durable. Once you use them, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. We also have a dedicated controller available. *For more details, please refer to the PDF materials or feel free to contact us.

  • Other processing machines
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0518 Repurposing the talc hopper, bridge countermeasures

0518 Repurposing the talc hopper, bridge countermeasures

Especially, no welding is required, and it can be easily installed! Examples of using the Brody disk.

When calcium carbonate was introduced into the hopper for talc, a bridge occurred, and to resolve this, a Brodisk was used. Since it is a square hopper of about 1000×1000, a standard Brodisk (BD-15) was installed, with one on each side for a total of four, and due to the special shape of the discharge section, two Brodisk Minis were installed here, which resolved the trouble. If you experience issues with powder discharge due to repurposing of hoppers or equipment, or changes in raw material types, please consider installing this equipment. It can be easily installed without the need for welding. 【Product Specifications】 ■ Brodisk "BD-15S-B" x 4 ■ Brodisk Mini "BD-08S-B" x 2 *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0520 Resolution of rat holes in aluminum hydroxide

0520 Resolution of rat holes in aluminum hydroxide

We would like to introduce a case that has been consulted by users who are already using our Brodisk!

According to the user, the material originally had concerns about rat holes, but there were no issues when operating the broad disk at the time of equipment installation. However, since the rainy season (on days with high humidity), rat holes have started to occur, which prompted the consultation. We have resolved the issue by adding more broad disks and adopting a new controller with four built-in solenoid valves to turn on the air in small quantities. Users who are already using broad disks are also welcome to contact us if they encounter any problems. 【Product Specifications】 ■ Broad Disk "BD-15S-B" x 8 ■ Controller "C-SV4" x 1 *For more details, please refer to the PDF document or feel free to contact us.

  • Other processing machines
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
0537 Residual measures for the dust collector hopper section

0537 Residual measures for the dust collector hopper section

Since configurations are important, we kindly ask customers who are interested to please consult with us, even if it may be a bit of a hassle!

A blower disk has been installed to prevent residuals that occur at the discharge bridge and in the four corners of the existing dust collector. This equipment has a simple structure, but it generally offers sufficient effectiveness. However, since the arrangement is important, we encourage interested customers to consult with us, even if it may be a bit of a hassle. We can provide specific advice. 【Product Specifications】 ■ Blower Disk: BD-15S-B, 8 pieces 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of strength and durability, especially considering the risk of foreign matter contamination. The silicone disk in this equipment excels in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is crucial! We provide guidance on what should be done. A dedicated controller is also available. *For more details, please refer to the PDF materials or feel free to contact us.

  • Other processing machines
  • Broad Disc

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration

Search Keywords Related to Broad Disc

Related Categories of Broad Disc

COPYRIGHT © 2001-2026 IPROS CORPORATION ALL RIGHTS RESERVED.