ジョブル List of Products and Services

The XE10-110 kit A is a set that includes one indoor 1-port transmitter "XE10-110-TX" from the EPoC (Ethernet & Power over Coaxial) series and one indoor 1-port receiver "XE10-110-RX" powered by a power adapter.

• LAN construction and wiring work
• Surveillance Camera System
• others

The IP09CK is a coaxial cable long-distance transmitter that can extend Ethernet up to 1,000 meters, typically up to 100 meters. By combining it with its sister product "IP09," it allows for a mix of coaxial and LAN cables, enabling further extension. It also supports low power consumption with EEE (Energy-Efficient Ethernet). It has a built-in surge protector for safe use. - Long-distance Ethernet transmission with coaxial cables of 5C-2V or higher - Extension up to 500 meters at 100Mbps and up to 1,000 meters at 10Mbps (for 5C-FB) - Compatible with 10BASE-T/100BASE-TX/100BASE-T1 - Supports EEE (Energy-Efficient Ethernet) - Built-in surge protector

• Other security and surveillance systems
• LAN construction and wiring work
• others

This is a transmitter that extends VGA (analog RGB), USB 2.0, audio, infrared remote control signals, and RS232C up to 140 meters using CAT5e or CAT6 LAN cables (UTP/STP 24AWG solid wire). The transmitter allows for loop output of the VGA signal, enabling video confirmation near VGA output devices.

• Other PCs and OA equipment
• Other image-related equipment
• others

The IP09K is a product that enables long-distance Ethernet transmission with a single LAN cable. The IP09K is a set of two units of the IP09, which functions as both a transmitter and a receiver. It is primarily used for one-to-one connections, but it can also be used as a repeater, allowing for distance extension with each additional unit. (The IP09 is also available for individual sale.) - With a one-to-one connection, it can extend up to 500m at 100Mbps and up to 800m at 10Mbps. - Supports low power consumption with EEE. - Built-in surge protector (with a withstand voltage of 1.5kV).

• Other security and surveillance systems
• others
• LAN construction and wiring work

The 2E10-110-TX is an EPo2 (Ethernet & Power over 2 wires) transmitter (TX) with one PoE Plus compatible LAN port. It operates using Po2 power from an EPo2 receiver located up to 600 meters away via two-wire cables such as telephone lines or UTP/STP, transmitting Ethernet and power to cameras and other devices connected to it. It enables the construction of intercoms, elevator cameras, surveillance systems, etc., using existing telephone lines.

• LAN construction and wiring work
• Surveillance Camera System
• others

The VDS6500A is a camera transmission device that can transmit 2-channel video signals, power, and UTC signals over long distances using a single coaxial cable. It supports four types of video signals: AHD, HD-TVI, HDCVI, and Composite (NTSC/PAL). Each of the two channels is compatible with UTC (Up-the-Coax), allowing for individual control of two cameras. * CH1 and CH2 can each accept different video signals (mixed signals are possible). * UTC is not compatible with all cameras. If you are using it for the first time, please contact us in advance. - Long-distance multiplex transmission of 2-channel video signals, power, and UTC signals using a single coaxial cable. - Power supply of up to 4A total at DC12V is possible (maximum 2.5A individually). - Easy modification/addition of existing cameras. - Mixed video signals can be transmitted. - RF modulation transmission is resistant to noise. * The VDS6500A is not compatible with the VDS6500 (discontinued product).

• Image Transmission Equipment
• Surveillance Camera System
• others

The JCP-101HD is a transmitter that multiplexes two channels of AHD/HD-TVI/HDCVI/composite video signals (which can be mixed) and transmits them over a single coaxial cable. One of the two channels is transmitted in baseband, while the other channel is transmitted using RF modulation. It is effective for updating or adding cameras using existing cameras and coaxial cables.

• Image Transmission Equipment
• Surveillance Camera System
• others

The EPoC series is a PoE Plus compatible IP long-distance coaxial cable transmission device that can transmit Ethernet and power (PoE) over a single coaxial cable for long distances. It extends the transmission distance, which is limited to 100m with standard Ethernet, up to 1,200m (using 5C-2V or higher) without the need for repeaters or other devices in between. We offer not only indoor models but also outdoor transmission devices that are waterproof and equipped with lightning protection. 【Features】 ■ Achieves long-distance Ethernet transmission at a lower cost than fiber optics ■ Flexible and free system construction with a rich lineup of products ■ Supports the introduction of new systems utilizing existing wiring and equipment *For more details, please refer to the PDF materials or feel free to contact us.

• Surveillance Camera System
• LAN construction and wiring work
• others

The SEAT-type surge protector JUP480F protects equipment from surge damage by absorbing surge energy internally. The absorbed energy is slowly released through the ground wire. It can be easily retrofitted by connecting it in parallel to the AC power cable, eliminating the need to cut the wires. Since there are no specific requirements for ground resistance, it is effective in protecting equipment in environments with poor grounding.

• Other safety equipment
• others
• Other FA equipment

The SEAT method surge protector J1S-320V removes surges from AC power lines simply by connecting it to an AC power outlet. - Surge protector compatible with AC 100-320V 50Hz/60Hz - Protects devices from various surges just by connecting to an AC power outlet Effective against surges caused by chattering, ON/OFF of inductive load circuits, electromagnetic pulses, and sparks, which conventional lightning arresters cannot eliminate - The surge removal method SEAT (Surge Energy Absorb & Transfer) has been patented in Japan (Patent No. 5192002), as well as in the United States (US 8295024B2), China (ZL 201010111239.8), and Taiwan (I 390816).

• Other safety equipment
• Other FA equipment
• others

- Converts HDMI signals to HD-TVI signals for output. (Includes HDMI video signal loop output) - Input resolutions (HDMI): 800x600, 1024x768, 1280x720, 1280x1024, 1440x900, 1920x1080 - Output resolutions (HD-TVI): 720p 50/60Hz or 1080p 25/30Hz - The resolution of the HDMI video loop output will match the input HDMI resolution. (Audio will not be output.) - The output resolutions of 720p and 1080p for HD-TVI can be switched using a toggle. - The power LED and operation LED allow for quick understanding of the device's status.

• Other image-related equipment
• Other security and surveillance systems
• others

The JAHD-ER03HR is a converter that converts HDMI video signals to AHD signals. - Converts HDMI signals to AHD signals - Maximum HDMI input resolution is 1080p (1920x1080) - HD signal output can be selected from 720p or 1080p - Enhanced security when using AHD-compatible recorders - HDMI video signal can be looped out (audio is not output) - Allows installation of a monitor without needing an additional HDMI splitter, even with devices that have only one HDMI output (using loop output) - Used in various scenarios, such as recording the operation screen of a PC handling important information.

• Other image-related equipment
• Other security and surveillance systems
• others

The AD001HD4 converts AHD/HD-TVI/HDCVI/composite video signals to HDMI/VGA/composite video. - Supports AHD/HD-TVI/HDCVI video input at 1080p 25/30Hz and 720p 25/30/50/60Hz, as well as composite video input. - Output options include HDMI, VGA, and composite/loop output. - Three types of signal outputs can be output simultaneously. - In HD input mode, it is possible to input two channels of HD/composite video and switch output/PIP output. *Simultaneous input of AHD and HDCVI is not possible in HD input mode (but combinations with HD-TVI/composite are possible). - HDMI output supports 480p/576p/720p/1080i/1080p. - Composite video output supports NTSC/PAL. - Power adapter included.

• Other image-related equipment
• Other security and surveillance systems
• others

- In standard Ethernet, the maximum transmission distance is up to 100m, but it can be extended up to 600m (using 5C-2V or higher) without inserting repeaters or other devices. - It transmits the Ethernet and power (PoE) necessary for installing IP cameras using existing coaxial cables. - Up to 4 cameras (RU/R) can be connected to one network device (LU). - Using 5C-2V, it achieves a maximum bidirectional communication speed of 100Mbps over a distance of up to 600m. - It incorporates TVS/GDT (surge absorbers/varistors) in the link cable connection terminals to protect the devices from surges.

• Surveillance Camera System

The "PoE/PoE Plus Power Receiving Ethernet Repeater" is a product that extends the transmission distance of Ethernet by up to 200m with a single unit. It can connect up to four units between hosts, allowing for a maximum extension of 500m. With a low power consumption of approximately 1.2W, it supplies power to PoE devices while minimizing attenuation. We offer two products in our lineup: "Standard Type" and "IP65 Waterproof and Dustproof Type." It also supports 1000BASE-T, making it suitable for high-capacity data communication. 【Features】 ■ Supports STP cables/connectors for noise-resistant transmission ■ Extends Ethernet at 10/100/1000M speeds ■ Operates on PoE power, eliminating the need for an additional power supply ■ Wide operating temperature range of -40 to 75°C (for waterproof and dustproof type) *For more details, please refer to the documentation. Feel free to contact us with any inquiries.

• Other network tools

- Ultra-compact 4ch DVR that can be installed anywhere - Supports AHD/HD-TVI (720p/1080p) and composite video (can be mixed) - Capable of recording 4ch mono audio simultaneously with video - Supports recording to HDD/SSD/SD card/USB memory/USB HDD * Recording media such as HDD are optional - Operates on DC 9-36V, making it compatible with a wide range of power sources beyond just vehicle or included power adapter - Low power consumption allows for operation with rechargeable batteries or solar batteries - By connecting an optional GPS antenna (model number: ETGM-5019), automatic time correction and location information recording are possible - Operates in temperatures from -20 to 70°C (when recording to SD card), suitable for installation in outdoor waterproof boxes - Backs up recorded video to SD card/USB memory/USB HDD - Backed-up recorded video can be played on Windows PC (playback software included)

• Surveillance Camera System
• others
• Video Recorder

The HE01ERK transmits HDMI signals over LAN cables up to 40m (1920x1200p). It is convenient for displaying PC video or DVR footage on a monitor located a short distance away. - Transmits HDMI (up to 1920x1200p) using a single CAT5e/6 LAN cable (CAT6 or higher recommended). *For longer distance transmission, the HE03 (HDCP compatible) can transmit up to 150m. - Both ends of the transmission cable use RJ45, allowing for commercially available LAN cables (straight wiring). - Operates on power supplied from the HDMI port. - Sends built-in EDID to HDMI output devices. - Not HDCP compatible. - The HE01SET (transmitter) and HE01SER (receiver) set includes a DC jack to micro USB conversion cable. *If the input HDMI signal level is low, the transmission distance may be shorter. *The power for this device is supplied from the HDMI port of the video output device. If the supplied power is insufficient for normal operation, please provide power to the HE01SET using a USB or a separately sold DC 5V power adapter (LTE10UW-S1-BS33).

• Image Transmission Equipment
• Other security and surveillance systems
• others

Our company offers a wide range of "AHD/HD-TVI compatible compact LCD monitors." High-resolution analog video display and composite video input are also possible. We have a diverse selection of products, from lightweight plastic-cased wide LCD monitors to high-resolution LCD monitors with metal casings. 【Product Introduction】 "AHD/HD-TVI and Composite Video Input Compatible LCD Monitor" Features a lightweight plastic casing. "AHD/HD-TVI, Composite Video, and VGA Input Compatible Metal Casing LCD Monitor" VGA input compatible with video display from PCs and recorders. "AHD/HD-TVI, Composite Video, HDMI, and VGA Input Compatible Metal Casing LCD Monitor" Supports PIP function to display two videos simultaneously. "AHD/HD-TVI, HDMI, DVI, and VGA Input Compatible Metal Casing LCD Monitor" 15.6-inch wide, with a resolution of 1920×1080, clearly displays 1080p video. "AHD/HD-TVI and Composite Video Input Compatible Rechargeable Test Monitor" Automatically detects and displays NTSC and PAL video. *For more details, please refer to the catalog. Feel free to contact us with any inquiries.

• Other image-related equipment

The HE03 transmits HDMI signals over LAN cables (CAT5e/6/7 UTP/STP 24AWG) for long distances. The maximum supported resolution is 1080p 60Hz and 1920✕1200 60Hz. The HE03T (transmitter) can loop output the HDMI input signal, allowing video display on a local monitor without using a splitter near the HDMI output device. Package contents: HE03T x1, HE03R x1, power adapter x2.

• Image Transmission Equipment
• Other security and surveillance systems
• others

JPX201 / JIPX201 (waterproof type) is an Ethernet repeater that supports 10/100/1000M PoE/PoE Plus power supply. It operates via PoE or PoE Plus power supply and extends Ethernet up to 200m. Additionally, it can connect up to 4 devices, allowing for an extension of up to 500m. It is capable of supplying power to devices compatible with PoE or PoE Plus.

• Other security and surveillance systems

- A single coaxial cable, whether existing or newly installed, transmits AHD or composite (NTSC/PAL) video signals along with camera power in a superimposed manner. - AHD supports 720p and 1080p, allowing for the transmission of high-resolution HD quality video. - With a 5C-FB cable, power transmission of DC12V 1A is possible up to 800m, and 1.5A up to 500m. - With a 5C-2V cable, power transmission is possible up to 600m (0.9A), and with a 3C-2V cable, up to 300m (0.8A). - Modulating and transmitting AHD/composite video is also effective for noise countermeasures in cases where noise occurs during normal transmission. - The power can be used for devices other than the camera, allowing for the installation of DC12V equipment.

• Image Transmission Equipment
• Surveillance Camera System
• others

- Transmits USB over CAT5e/6 cable up to 60m. - Supports USB 2.0 (High-Speed) and USB 1.1 (Low-Speed/Full-Speed). - Transmits between UE03T (USB device side) and UE03R (PC side). - UE03T (USB device side) has a 4-port USB hub function. - UE03R (PC side) receives power from the USB port, so no power adapter is needed. - Supports imaging devices such as printers and USB cameras, in addition to mice and keyboards. - This is a set of UE03T, UE03R, and a power adapter (for UE03T).

• Other security and surveillance systems
• Other PCs and OA equipment
• others

The HD02-4K is a splitter that outputs one HDMI signal to two outputs. - Supports video up to 4K 30Hz - EDID supports built-in/signal pass-through/recording - Maximum signal bandwidth for HDMI signals is up to 10.2Gbps - Audio supports LPCM 7.1 192kHz, Dolby TrueHD, and DTS-HD MA (pass-through) - Supports HDCP 1.4 - Power adapter included

• Other image-related equipment
• Surveillance Camera System
• others

MLT4-B1-1-100 is a surge protector compatible with power supplies and control signals, including contact signals, up to DC100V. - No grounding work is required to protect devices from various surges. It blocks surges from power wiring and surges caused by electromagnetic pulses. It is also effective against surges caused by chattering and the OFF state of inductive load circuits, which cannot be eliminated by conventional lightning arresters.

• power supply
• Other safety equipment
• others

The surge protector JSPAW-CH-6-250 for AC power sources protects equipment from high voltage surges caused by induced lightning and other sources that enter power wiring for outdoor installations. It also blocks surges caused by induced lightning, switching, inrush current, and electromagnetic pulses.

• power supply
• Other safety equipment
• others

The SDIVPD extends HD-SDI signals up to 300 meters using a single coaxial cable (when using 5C-FB). It also allows for the combined transmission of camera power and RS485 signals. It can supply up to 2A of DC12V power to the camera, making it effective for connecting to cameras with relatively high power consumption.

• Image Transmission Equipment

EP01 is a power supply adapter that utilizes the unused wires of a 10/100M Ethernet (LAN cable) to provide power. - It transmits power using two unused pairs in the 10/100M LAN wiring. - Since you can freely choose the power supply, it can power various non-PoE devices. - It can be used not only for power supply but also for transmitting contact signals and RS485 signals. * It is used by modifying the power adapter included with the network device. * It cannot be used with 1000BASE LAN. * The transmission distance varies depending on the power consumption of the power adapter and device, as well as the quality of the cable.

• Other security and surveillance systems

The HE02EI is an HDMI transmitter that extends HDMI and infrared remote control signals up to 70 meters (1080p/60Hz CAT6a) using a single LAN cable. It can display content from gaming consoles, Blu-ray players, and HD television video on AV amplifiers or HD televisions located at a distance. The direction of infrared transmission can be switched between "transmitter to receiver" or "receiver to transmitter."

• Image Transmission Equipment
• Other security and surveillance systems
• others

The SDI02 is a converter that converts HDMI signals to SDI signals. It converts HDMI output signals from devices such as digital video recorders (DVRs) into SDI signals. You can input HDMI output camera footage or the HDMI output screen from a DVR into an SDI switcher or SDI recorder. *Please note that HDCP is not supported. If you input a signal that supports HDCP, such as from consumer DVD/BD players, it will not be converted to SDI output. The SDI signal supports not only SD-SDI/HD-SDI but also 3G-SDI signals at 1080p 60Hz. It converts HDMI audio signals to embedded SDI audio. The HDMI audio signals are compatible with LPCM 2ch and LPCM 7.1ch surround sound.

• Other image-related equipment
• Other security and surveillance systems
• others

SW105 is a 5-port Ethernet switch for network cameras. Four of the five ports support PoE Plus power supply. PoE power supply can provide up to 39W per port, with a total maximum of 75W across four ports. Transmission of up to 200 meters is possible with LAN cables (CAT6 or higher).

• Other image-related equipment

MLT4-B1-1-12 is a surge protector compatible with power supplies and control signals up to DC12V, as well as contact signals. - No grounding work is required to protect devices from various surges. It blocks surges from power wiring and surges caused by electromagnetic pulses. It is also effective against surges caused by chattering and the OFF state of inductive load circuits, which conventional lightning arresters cannot eliminate.

• power supply
• Other safety equipment
• others

The SDI04D is an SDI signal distributor that outputs 4 copies of SD/HD/3G-SDI signals. - The SDI signal input to the distributor is corrected and output using reclocking and equalization functions, allowing for the re-extension of signals transmitted over long distances. * Reclocking function: A feature that removes jitter (fluctuation) from the signal by reconstructing the clock, returning it to accurate timing. * Equalization function: A feature that corrects waveform distortion caused by transmission, restoring it to a clean waveform. - It supports 7.1 channel audio.

• Other image-related equipment
• Surveillance Camera System
• others

The IPC-600P can transmit PoE/PoE Plus Ethernet over coaxial cable up to 600m. Additionally, it achieves a communication speed of up to 100Mbps in the direction from the camera to the Ethernet switch (monitor side), allowing for smooth transmission of high-resolution IP camera footage with large data volumes. Furthermore, by connecting a camera-specific switch SW105 or a DC56V power adapter to the IPC-600P-T on the monitor side, it is also possible to supply up to 25.5W (5C-2V 100m) to the camera. This is effective for connecting IP cameras in remote locations such as outdoors or for upgrading from existing analog cameras to IP cameras.

• LAN construction and wiring work
• Surveillance Camera System
• others

- Surge protector compatible with 10/100BASE Ethernet wiring - Supports power supply via PoE and PoE Plus - Protects devices from various surges without the need for grounding, including induced lightning (LFS), power switching surges (PSS), inrush current (SIC), and electromagnetic pulses (EMP) - Passed tests with combination waveforms (1.2/50μs, 8/20μs) at 6kV/3kA - Complies with IEC standard "IEC 61643-21," equivalent to "JIS C5381-21" (surge protective devices for communication and signal circuits, Category C2) - Complies with IEC standard "IEC 61000-4-4," equivalent to "JIS C1000-4-4" - New method of accumulating surges without discharging to ground and releasing them gradually (between pins 1-2 and 3-6) with patents obtained in Japan (patent number 5192002), the USA, China, and Taiwan * Protection for the power system between pins 4/5-7/8 is provided by conventional varistors. - DIN rail adapter included

• Other security and surveillance systems
• Other safety equipment
• LAN construction and wiring work

PC1A is a DC 12V output voltage converter that converts an AC/DC power supply of 18V or higher to DC 12V. It is ideal for supplying DC 12V to cameras and other devices when transmitting over long distances with AC/DC 24V. It can supply power up to DC 12V 1A (12W).

• power supply
• Other FA equipment
• others

The PC500 is a DC 12V output voltage converter that converts a power supply of AC/DC 15V or higher to DC 12V. It is ideal for supplying DC 12V to cameras and other devices when transmitting over long distances with AC/DC 24V. It can supply power up to DC 12V/500mA (6.0W).

• power supply
• Other FA equipment
• others

DR01 is a repeater that can extend DVI-D signals (single link) up to 50 meters using a DVI cable. The input signal supports DVI-D signals up to 1080p or 1920✕1200.

• Other PCs and OA equipment

PoE/PoE Plus Ethernet is transmitted using coaxial cables. The transmission distance of standard PoE Ethernet can be extended from the usual 100m to a maximum of 300m. Since it transmits by connecting at both ends of the transmission cable, it can be used in places where relay devices cannot be installed, such as overhead wiring or underground burial. By using PoE Plus (IEEE802.3at) switches or injectors, it can supply up to 14W of power to receiving devices such as IP cameras. The operating temperature range is wide, from -10 to 60°C, allowing it to be used in harsh temperature environments.

• LAN construction and wiring work
• Surveillance Camera System
• others

The SP016P protects LAN wiring that includes PoE/PoE Plus power supply for up to 16 systems with 10/100/1000M simultaneously. It diverts high voltage surges caused by induced lightning and other sources away to the ground before reaching the equipment. The surge protector should be installed as close as possible to the equipment that needs protection. When protecting a camera, it should be placed near the camera, and when protecting a monitor or NVR/server, it should be installed near the monitor/DVR/server. The basic principle of surge protection is to install devices on both the camera side and the display device (monitor) side. If the SP016P is installed on the monitor side, additional devices such as the IP06PH or JPOE-B2-1, SP006P can be installed for each camera wiring on the camera side.

• Other network tools
• Other security and surveillance systems
• LAN construction and wiring work

HVY01 is a converter that converts HDMI (or DVI-D) to VGA (analog RGB) or component video and analog stereo audio. (Output resolution can be changed) * If connecting DVI-D, please prepare a separate DVI to HDMI conversion adapter. - Maximum resolution: VGA (analog RGB): 1920✕1200, Component: 1080p - Supports 2-channel audio output (stereo) - Settings via OSD (on-screen display) - Power adapter included * Not compatible with HDCP

• Other image-related equipment

The DE02E can transmit DVI-D signals over LAN cables up to 100 meters. It can connect PC or DVR video to monitors located at a distance. - Transmits DVI-D (single link) signals up to 100 meters using CAT5e/6/6a/7 UTP/STP cables (CAT6 cables or higher recommended) - Both ends of the transmission cable use RJ45, allowing for commercially available LAN cables (straight wiring) - Maximum resolution: 1920x1200 - Supports HDCP 1.4

• Image Transmission Equipment
• Other security and surveillance systems
• Other PCs and OA equipment

- Transmits HDMI video and audio signals over a single coaxial cable. - Can transmit 1080p at 60Hz up to 70m using a 5C-FB cable. (720p, 1080i, and 1080p at 30Hz can be transmitted up to 150m.) - Supported resolutions are 480i, 576i, 720p, 1080i, and 1080p. - Includes one transmitter, one receiver, and two power adapters. - Daisy chaining for further extension is possible (requires an additional HE01CR). - Supports HDMI 7.1CH audio (only LPCM). - Compatible with HDMI 1.3. * Does not support transmission of signals other than video and audio. * Does not support HDCP. * The included receiver HE01CR is only one unit. An additional HE01CR (sold separately) is required for further extension.

• Image Transmission Equipment
• Other security and surveillance systems
• others

This is a converter that converts SD-SDI/HD-SDI/3G-SDI signals transmitted via coaxial cable to HDMI (supports resolutions of 720p, 1080i, and 1080p). • Active through output function included In addition to HDMI output, active through output is possible. The SDI signal output can also be further extended due to the active through feature. • Embedded audio support It supports embedded audio, allowing video and audio to be transmitted together. 【Transmission distance guidelines (using 5C-FB)】 - SD-SDI (SMTP 259M 270Mbps): up to 300m - HD-SDI (SMTP 292M 1.45Gbps): up to 150m - 3G-SDI (SMTP 424M 2.97Gbps): up to 80m

• Other image-related equipment
• Other security and surveillance systems
• others

- It blocks surges that occur in SD/HD/3G-SDI video signals (BNC connection). - It protects equipment from sudden voltage spikes caused by high-voltage surges such as induced lightning. - It can also be used with analog cameras and TV/CATV antenna cables. - With BNC male on one end and BNC female on the other, it can be easily installed into existing wiring. - It allows voltages below DC24V to pass through.

• Other security and surveillance systems
• Other safety equipment
• others

- Transmits VGA (analog RGB) up to 100m using a single CAT5e/6 cable. - Maximum transmission distance varies depending on VGA resolution: 640✕480/800✕600: 100m, 1024✕768: 75m, 1280✕1024: 60m. - Passive type, no power supply required. - Built-in virtual DDC in the transmitter to avoid misrecognition of display resolution/frequency. - Set includes VE01P-T (transmitter) and VE01P-R (receiver). - Both ends of the transmission cable use RJ45, compatible with commercially available LAN cables (straight wiring). - Sync mode setting switch (transmitter). - Sync deviation correction due to signal delay during transmission (receiver). * VE01P (= TTP111VGA) does not use power for simple transmission, so color distortion or ghosting may occur depending on the transmitted signal and operating environment. When displaying text or graphics on a PC screen, the above noise may be more noticeable, so the use of sets like VE02ALT and VE02DALS is recommended.

• Other PCs and OA equipment