テイエスエスジャパン List of Products and Services

The "MFA-R 0.2-6 Magnetic Field Microprobe" is an active near-field microprobe that requires a BT 706 bias tee to operate. It detects magnetic fields from IC pins on components, thin conductive paths, and tiny SMD components. It has the same basic structure as the "MFA-R 0.2-75," but only the frequency characteristics differ. There is a black dot marked laterally on the coil opening of the probe head, so please check the orientation before measuring. 【Specifications】 ■ Type: Near-field Microprobe ■ Size: Microchip size ■ Supported Frequency Range: 100MHz to 6GHz ■ Connector: SMA female, Jack ■ Resolution: 300μm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "MFA 02 Set" includes, for example, two high-resolution near-field microprobes capable of measuring low-frequency magnetic fields up to 1GHz in signal conductors (150μm), SMD components, or IC pins, along with a bias tee and a dedicated cable. The preamplifier (9V, 100mA) is powered through a bias tee BT 706 with an impedance of 50Ω, and the magnetic field microprobes are connected to a spectrum analyzer or oscilloscope via the BT 706. 【Specifications】 ■ Type: PCB Emission Near-Field Microprobe ■ Supported Frequency Range: 1MHz to 1GHz *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "MFA 01 Set" includes three high-resolution magnetic field microprobes capable of measuring magnetic fields up to 6GHz in signal conductors (150μm), SMD components, or IC pins, along with a bias tee and a dedicated cable. Each microprobe has a built-in preamplifier. The preamplifier (9V, 100mA) is powered through a bias tee BT 706 with a 50-ohm impedance, and the magnetic field microprobes are connected to a spectrum analyzer or oscilloscope via the BT 706. 【Specifications】 ■ Type: PCB Emission Near-Field Microprobe ■ Supported Frequency Range: 1MHz to 6GHz *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-K 7 Magnetic Field Probe" is a passive near-field probe that detects semicircular magnetic field lines using two coils. The probe functions like a coupling clamp. Unlike the "LF-U 5" probe, it does not detect magnetic field lines entering from the side. The magnetic field enters through the first coil, curves in a circular shape within the probe head, and detects the uneven magnetic field exiting through the second coil. It does not detect overlapping uniform magnetic fields. 【Specifications】 ■ Type: Near-field probe ■ Size: 6×10mm probe head ■ Frequency range: 100kHz to 50MHz ■ Connector: SMB male, Jack ■ Resolution: 5mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-U 2.5 Magnetic Field Probe" is a passive near-field probe designed to selectively detect RF currents in conductive paths, SMD components, and IC pins. The probe head features a magnetically active gap approximately 0.5mm wide. It functions similarly to the "LF-U 5" probe. While the "LF-U 5" is suitable for larger components such as cables and connectors, this product is designed for SMD components and pins. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ4mm probe head ■ Frequency range: 100kHz to 50MHz ■ Connector: SMB male, Jack ■ Resolution: 0.5mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-R 50 Magnetic Field Probe" is a passive near-field probe with a head size of 10mm in diameter, designed to measure assemblies, devices, or cables up to 3cm away. This product offers performance that is intermediate between the "LF-R 400" and "LF-R 3" probes in terms of diameter, sensitivity, and resolution. Langer's near-field probes are compact and very easy to use, and they are electrically well-shielded due to the current-damping sheath. 【Specifications】 ■ Type: Near-field Probe ■ Size: Φ10mm Probe Head ■ Frequency Range: 100kHz to 50MHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-U 5 Magnetic Field Probe" is a passive near-field probe designed to detect magnetic fields from a wide range of conductive paths, cables, connectors, electronic components, and more. The probe functions like a coupling clamp. Position the curved bottom of the probe on the surface of the component. It also detects magnetic field lines coming straight or from the side from other sources relative to the probe. 【Specifications】 ■ Type: Near-field Probe ■ Size: 6×6mm Probe Head ■ Frequency Range: 100kHz to 50MHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-B 3 Magnetic Field Probe" is a passive near-field probe, with the internal coil arranged perpendicular to the shaft. When the probe head is used vertically against the assembly or device being measured, accurate measurements can be obtained. This product detects magnetic field lines radiating at a 90° angle from the object being measured and does not detect magnetic field lines entering from the side. Langer's near-field probes are compact and very easy to use, and they are electrically well-shielded by a current-damping sheath. 【Specifications】 ■ Type: Near-field Probe ■ Size: Φ4mm Probe Head ■ Frequency Range: 100kHz to 50MHz ■ Connector: SMB male, Jack ■ Resolution: 2mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-R 3 Magnetic Field Probe" is a passive near-field probe that directly detects RF magnetic fields on assemblies with high resolution, including IC pins, IC cases, conductive paths, decoupling capacitors, and areas surrounding EMC components. It has the same basic structure as the "LF-R 50" and "LF-R 400" probes, but this product offers the highest resolution. It is suitable for measurements close to components with high magnetic field strength, but not for measurements from a distance. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ3mm probe head ■ Frequency range: 100kHz to 50MHz ■ Connector: SMB male, Jack ■ Resolution: 1mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "LF-R 400 Magnetic Field Probe" is a passive near-field probe with a head size of 25mm in diameter, featuring high sensitivity and suitable for measurements within a maximum range of 10cm around assemblies and devices. Langer's near-field probes are compact and very easy to use, and they are electrically well shielded due to the current-damping sheath. It can be connected to a spectrum analyzer or oscilloscope with a 50Ω input. The magnetic field probes in the "LF series" do not have a built-in 50Ω termination resistor. 【Specifications】 ■ Type: Near-field Probe ■ Size: Φ25mm Probe Head ■ Frequency Range: 100kHz to 50MHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-E 10" electric field probe is a passive near-field probe. The electrode width of the probe head is approximately 0.2mm, allowing it to pinpoint the location of even the smallest electric field sources, such as a conductive path of 0.1mm or a single IC pin. Since the electrode surface needs to be placed directly on the measurement target where the electric field strength is high, it is not suitable for wide-range measurements. For measuring larger areas, please use the "RF-E 02" or "RF-E 05". 【Specifications】 ■ Type: Near-field probe ■ Size: 0.5x2mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack ■ Resolution: 0.2mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The RF-E 09 electric field probe is a passive near-field probe designed for use with scanners manufactured by Langer. The electrodes of the probe head detect separated electric fields on the surface of ICs. It functions well within a distance of 0.5 to 10 mm from the assembly. By placing and holding small square electrode surfaces on components or printed circuit boards, it can detect sources of electrical interference. 【Specifications】 ■ Type: Near-field probe ■ Size: 10x10 mm probe head ■ Frequency range: 30 MHz to 3 GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The RF-E 05 electric field probe is a passive near-field probe designed for use with scanners manufactured by Langer. The electrode width of the probe head is approximately 0.5mm, allowing for accurate identification of electric fields around clocked lines, IC pins, and small components. By placing and holding it on components or printed circuit boards, it can detect sources of RF electrical interference. 【Specifications】 ■ Type: Near-field probe ■ Size: 1x8mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack ■ Resolution: 0.6mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The RF-E 04 electric field probe is a passive near-field probe designed for use with scanners manufactured by Langer. It has the same basic structure as the "RF-E 03" and "RF-E 09" probes. It functions well at distances of 0.5 to 10 mm from the assembly. By placing and holding a small square electrode surface on components or printed circuit boards, it can detect sources of electrical interference. 【Specifications】 ■ Type: Near-field probe ■ Size: 5x5 mm probe head ■ Frequency range: 30 MHz to 3 GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The RF-E 03 electric field probe is a passive near-field probe designed for use with scanners manufactured by Langer. The lower electrode surface of the probe head measures approximately 4x4mm, allowing for the identification of small electric field sources such as conductive paths and single components on printed circuit boards. The lower surface of the probe head is placed directly on the object being measured to detect the emitted electric field. 【Specifications】 ■ Type: Near-field probe ■ Size: 4x4mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-E 02" electric field probe is a passive near-field probe. It detects separated electric field sources on bus structures, large components, or the surfaces of power supplies. The lower electrode surface of the probe head is approximately 2x5 cm and works well at a distance of 1 to 2 cm from the component. It has the same basic structure as the "RF-E 05" and "RF-E 10" probes. 【Specifications】 ■ Type: Near-field probe ■ Size: 23x53 mm probe head ■ Frequency range: 30 MHz to 1.5 GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-K 7-4" magnetic field probe is a passive near-field probe that detects semicircular magnetic field lines entering the probe head in the opposite direction. The semicircular magnetic field lines are generated along linear, rod-like structures, cable connectors, and the edges of planar structural components. The probe functions like a coupling clamp. It does not detect overlapping uniform magnetic fields. 【Specifications】 ■ Type: Near-field probe ■ Size: 6x10mm probe head ■ Frequency range: 30MHz to 1GHz ■ Connector: SMB male, Jack ■ Resolution: 5mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-U 2.5-2" magnetic field probe is a passive near-field probe designed to selectively detect RF currents in conductive paths, SMD components, and IC pins. The probe head features a magnetically active gap of approximately 0.5mm, allowing for direct placement on the measurement target for assessment. It has the same basic structure as the "RF-U 5-2," but is more suitable for detecting smaller areas. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ4mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack ■ Resolution: 0.5mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The RF-U 5-2 magnetic field probe is a passive near-field probe designed to detect magnetic fields from a wide range of conductive paths, cables, connectors, electronic components, and more. The probe functions like a coupling clamp. When the probe head is placed directly on a component, it can detect magnetic field lines coming from other sources either straight on or from the side. It can be connected to a 50Ω input spectrum analyzer or oscilloscope. 【Specifications】 ■ Type: Near-field probe ■ Size: 6x6mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack ■ Resolution: 5mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-R 0.3-3" magnetic field probe is a passive near-field probe. Equipped with a compact probe head, it can measure magnetic fields with very high resolution, detecting even small components as interference sources. It also allows access to narrow spaces. It directly detects RF magnetic fields on assemblies with high resolution around IC pins, IC cases, conductive paths, decoupling capacitors, and EMC components. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ2.0mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-R 3-2" magnetic field probe is a passive near-field probe. It directly detects RF magnetic fields on the assembly with high resolution, including IC pins, IC cases, conductive paths, decoupling capacitors, and surrounding EMC components. It has the same basic structure as the "RF-R 50-1" and "RF-R 500-1" probes, but this product offers significantly higher resolution. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ3mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack ■ Resolution: 1mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-R 50-1" magnetic field probe is a passive near-field probe designed to measure assemblies, devices, or cables located up to 3 cm away. The probe head of this product has a diameter of 10 mm, which results in lower sensitivity compared to the 25 mm diameter "RF-R 400-1," but it offers high resolution. It can be connected to a spectrum analyzer or oscilloscope with a 50Ω input. The RF series magnetic field probes do not have a built-in 50Ω termination resistor. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ10mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "RF-R 400-1" magnetic field probe is a passive near-field probe with a head size of 25mm in diameter. It has high sensitivity and is suitable for measurements in a range of up to 10cm around assemblies and devices. The larger the tip diameter, the higher the sensitivity, allowing for the detection of magnetic fields over a wider area. It has the same basic structure as the "RF-R 50-1" and "RF-R 3-2". 【Specifications】 ■ Type: Near-field probe ■ Size: Φ25mm probe head ■ Frequency range: 30MHz to 3GHz ■ Connector: SMB male, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "XF-E 10" electric field probe is a passive near-field probe. The electrode width of the probe head is approximately 0.2mm, allowing it to pinpoint the location of even the smallest electric field sources such as conductive paths of 0.1mm width or single IC pins. It has the same basic structure as the "XF-E 04s" and "XF-E 09s" probes but offers higher resolution. Since it is necessary to place the electrode surface directly on the measurement target with high electric field strength, it is not suitable for wide-range measurements. 【Specifications】 ■ Type: Near-field probe ■ Size: 0.5x2mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack ■ Resolution: 0.2mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "XF-E 09s" electric field probe is a passive near-field probe. The electrodes of the probe head detect separated electric fields on the surface of the IC. It works well within a distance of 0.5 to 10 mm on the assembly. It has the same basic structure as the "XF-E 04s" probe, but by placing and holding small square electrode surfaces on components or printed circuit boards, it can detect sources of electrical interference. 【Specifications】 ■ Type: Near-field probe ■ Size: 10x10mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The 『XF-E 04s』 electric field probe is a passive near-field probe. The lower electrode surface of the probe head is approximately 5x5mm, detecting separated electric fields on the surface of the IC. By placing and holding a small square electrode surface on components or printed circuit boards, it can detect sources of electrical interference. 【Specifications】 ■ Type: Near-field probe ■ Size: 5x5mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "XF-U 2.5-1" magnetic field probe is a passive near-field probe designed to selectively detect RF currents in conductive paths, SMD components, and IC pins. The probe head features a magnetically active gap of approximately 0.5mm, which is positioned over the measurement target during measurement. Langer's near-field probes are compact and very easy to use, and they are also electrically well-shielded due to the current attenuation sheath. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ4mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack ■ Resolution: 0.5mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The 『XF-B 3-1』 magnetic field probe is a passive near-field probe. The internal coil is arranged perpendicular to the shaft, allowing for accurate measurements when the probe head is used vertically against the assembly or device being measured. For example, it can be approached from above to access difficult-to-reach printed circuit boards sandwiched between components. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ4mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack ■ Resolution: 2mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "XF-R 3-1" magnetic field probe is a passive near-field probe. It directly detects RF magnetic fields on the assembly with high resolution, including IC pins, IC cases, conductive paths, decoupling capacitors, and surrounding areas of EMC components. It has the same basic structure as the "XF-R 100-1" and "XF-R 400-1" probes, but this product has a significantly higher resolution. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ3mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack ■ Resolution: 1mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "XF-R 100-1" magnetic field probe is a passive near-field probe designed to measure assemblies, devices, and cables up to 3 cm away. Its wide bandwidth and high linearity allow for the identification of large components that may cause interference. In terms of head size, sensitivity, and resolution, it offers performance that is intermediate between the "XF-R 400-1" and "XF-R 3-1" probes. 【Specifications】 ■ Type: Near-field probe ■ Size: 10x10mm probe head ■ Frequency range: 30MHz to 6GHz ■ Connector: SMA female, Jack ■ Resolution: Φ10mm *For more details, please refer to the related links or feel free to contact us.

• EMC/Static electricity measuring equipment

The "XF-R 400-1 Magnetic Field Probe" is a passive near-field probe with a head size of 25mm in diameter. It has high sensitivity and is suitable for measurements within a maximum range of 10cm around assemblies and devices. The larger the tip diameter, the higher the sensitivity, allowing for the detection of magnetic fields over a wider area. Additionally, the XF series magnetic field probes come with a built-in 50Ω termination resistor. 【Specifications】 ■ Type: Near-field Probe ■ Size: Φ25mm Probe Head ■ Frequency Range: 30MHz to 6GHz ■ Connector: SMA female, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "SX-E 03 Electric Field Probe" is a passive near-field probe. The lower electrode surface of the probe head is approximately 4x4mm, allowing for the identification of small electric field sources such as conductive paths and single components on printed circuit boards. The lower surface of the probe head is placed directly on the object being measured to detect the emitted electric field. Langer's near-field probes are compact and very easy to use, and they are electrically well-shielded by a current-damping sheath. 【Specifications】 ■ Type: Near-field Probe ■ Size: 4x4mm Probe Head ■ Frequency Range: 1GHz to 10GHz ■ Connector: SMA female, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

We would like to introduce the "SX-B 3-1 (H field magnetic field probe)" that we handle. The internal coil is arranged perpendicular to the shaft, allowing for accurate measurements when the probe head is used vertically against the assembly or device being measured. Since the probe head is very small, it can be approached from above to access printed circuit boards and other components that are difficult to reach. It detects magnetic field lines radiating at a 90° angle from the object being measured, while it does not detect magnetic field lines entering from the side. 【Specifications】 ■ Type: Near-field probe ■ Size: Φ4mm probe head ■ Frequency range: 1GHz to 10GHz ■ Connector: SMA female, Jack ■ Resolution: 2mm *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "SX-R 20-1 Magnetic Field Probe" is a passive near-field probe that covers a frequency range of up to 20GHz. With its very compact probe head, it is possible to trace and identify very small RF magnetic field sources on components and ICs. Langer's near-field probes are compact, very easy to use, and are electrically well-shielded due to the current-damping sheath. 【Specifications】 ■ Type: Near-field Probe ■ Size: 6x6mm Probe Head ■ Frequency Range: 1GHz to 20GHz *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "SX-R 3-1 Magnetic Field Probe" is a passive near-field probe equipped with a compact probe head. It can measure RF magnetic fields with very high resolution and can detect small components as interference sources. Langer's near-field probes are compact and very easy to use, and they are electrically well-shielded by a current-damping sheath. 【Specifications】 ■ Type: Near-field Probe ■ Size: Φ3mm Probe Head ■ Frequency Range: 1GHz to 10GHz ■ Connector: SMA female, Jack ■ Resolution: 1mm *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "HR-E 40-1 Electric Field Probe" is a passive near-field probe that covers a frequency range of up to 40GHz. The probe head is isolated from the cable shield by a special attenuation system. Additionally, the probe includes a current attenuator and has a built-in 50Ω impedance matching network. 【Specifications】 ■ Type: Near-field Probe ■ Size: Chip-type (distance to internal electrode 0.5mm) ■ Supported Frequency Range: Up to 40GHz ■ Connector: 2.92mm female, Jack ■ Resolution: 0.2mm *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "HR-R 8-1 Magnetic Field Probe" is a passive near-field probe that covers a frequency range of up to 40GHz. The probe head is isolated from the cable shield by a special attenuation system. This product allows for direct magnetic field measurements on IC pins and conductor tracks, enabling the identification of magnetic field sources. 【Specifications】 ■ Type: Near-field Probe ■ Size: 9x9mm Probe Head ■ Supported Frequency Range: Up to 40GHz ■ Connector: 2.92mm female, Jack *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "LF1 Near-Field Probe Set" includes four magnetic field probes and a dedicated cable, allowing for the measurement of longwave, mediumwave, and shortwave frequencies emitted from electronic devices during the development process. The probe heads in this set are designed to progressively detect electromagnetic interference sources from IC pins to large components on the assembly. They can be connected to a spectrum analyzer or oscilloscope with a 50Ω input. 【Set Contents】 ■LF-R 400: H-Field Probe 100kHz to 50MHz ■LF-B 3: H-Field Probe 100kHz to 50MHz ■LF-U 2.5: H-Field Probe 100kHz to 50MHz ■LF-U 5: H-Field Probe 100kHz to 50MHz ■SMB-BNC: 1m Cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "RF4-E Probe Set" includes two passive electric field probes that measure electric fields in the frequency range of 30MHz to 3GHz (1.5GHz) for comparative purposes. These probes are designed for analyzing electric field distribution, detecting coupling mechanisms on modules, and evaluating RF voltage in power systems at signal lead switching edges. Langer's near-field probes are compact and very easy to use, and they are electrically well-shielded due to the current-damping sheath. 【Set Contents】 ■RF-E 02: E-Field Probe 30MHz to 1.5GHz ■RF-E 05: E-Field Probe 30MHz to 3GHz ■SMB-BNC: 1m cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "RF3 Mini Set" includes two passive magnetic field probes with a resolution of less than 1mm and one dedicated cable. It is capable of measuring electric and magnetic fields from 30MHz to 3GHz on electronic assemblies during the development process. It comes with a specially designed compact head that allows for detailed measurement of magnetic fields and interference currents in layout and component ranges. 【Set Contents】 ■RF-B 0.3-3: H-Field Probe mini 30MHz–3GHz ■RF-R 0.3-3: H-Field Probe mini 30MHz–3GHz ■SMB-BNC: 1m cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "RF2 Near-Field Probe Set" includes four passive magnetic field probes and one dedicated cable. It can measure electric and magnetic fields from 30MHz to 3GHz on electronic assemblies during the development process. The probe heads in this set can progressively identify the locations of RF magnetic field interference sources on electronic assemblies. 【Set Contents】 ■RF-R 400-1: H-Field Probe 30MHz to 3GHz ■RF-R 50-1: H-Field Probe 30MHz to 3GHz ■RF-U 5-2: H-Field Probe 30MHz to 3GHz ■RF-B 3-2: H-Field Probe 30MHz to 3GHz ■SMB-BNC: 1m cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "RF1 Near-Field Probe Set" includes four passive magnetic field probes and one dedicated cable. The probe heads in this set allow for measurements very close to electronic assemblies. It can inspect IC pins, conductive paths, components, and connectors, and identify sources of interference. 【Set Contents】 ■RF-K 7-4: H-Field Probe 30MHz to 1GHz ■RF-U 2.5-2: H-Field Probe 30MHz to 3GHz ■RF-R 3-2: H-Field Probe 30MHz to 3GHz ■RF-E 10: E-Field Probe 30MHz to 3GHz ■SMB-BNC: 1m cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "XF1 Near-Field Probe Set" includes four magnetic field probes, one electric field probe, and one dedicated cable. It is capable of measuring electric and magnetic fields from 30MHz to 6GHz on electronic assemblies during the development process. Due to its impedance matching, the sensitivity in lower frequency ranges is lower than that of RF-type probes. 【Set Contents (Partial)】 ■XF-R 400-1: H-Field Probe 30MHz–6GHz ■XF-R 3-1: H-Field Probe 30MHz–6GHz ■XF-B 3-1: H-Field Probe 30MHz–6GHz ■XF-E 10: E-Field Probe 30MHz–6GHz ■XF-U 2.5-1: H-Field Probe 30MHz–6GHz ■SMA-SMA: 1m Cable *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "SX-R 20-1 Set (Magnetic Field Probe)" includes a passive magnetic field probe for measuring high-frequency magnetic fields up to 20GHz during the development process, along with one dedicated cable. The probe head of the SX-R 20-1 can measure at positions close to electronic assemblies. It can inspect IC pins, conductive paths, components, and connectors, allowing for the identification of interference sources. [Set Contents] ■SX-R 20-1: H-Field Probe 1GHz to 20GHz ■SMA-SMA: 1m cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products

The "SX1 Set (Magnetic and Electric Field Probes)" includes three passive magnetic field probes and one dedicated cable. It is capable of measuring electric and magnetic fields in the high clock frequency range of 1GHz to 10GHz on electronic assemblies and ICs during the development process. Langer's near-field probes are compact and very easy to use, and they are electrically well-shielded due to the current-damping sheath. 【Set Contents】 ■SX-E 03: E-Field Probe 1GHz–10GHz ■SX-B 3-1: H-Field Probe 1GHz–10GHz ■SX-R 3-1: H-Field Probe 1GHz–10GHz ■SMA-SMA: 1m Cable ■Case *For more details, please refer to the related links or feel free to contact us.

• EMC countermeasure products