ミナギ Product Lineup

A plant engineering company contacted us during planning, anticipating a bridge in the resin grinding waste storage hopper. They requested a loan of the "Brodisk," which we promptly sent. Subsequently, they tested it and decided to adopt it for their new plant. 【Overview】 ■ Hopper dimensions: 2000×2000 ■ Discharge section dimensions: 500×500 ■ Target material: Resin film grinding waste (a few mm) and others 【Key Points of This Equipment】 ■ The elastic disk (silicone) is very important in terms of foreign matter contamination risk, as strength and durability are crucial. The silicone disk of this equipment excels in strength and durability. Once you use it, you will understand! ■ Control (how to aerate?) is important! We provide guidance on what to do. We also have a dedicated controller prepared. *For more details, please refer to the PDF materials or feel free to contact us. *Our website features numerous implementation examples, which can be checked via the link below.

We delivered a "Brodisk" to a concrete block manufacturing plant to address the blockage in the turn chute for aggregates. Initially, we lent the necessary number of units for them to try out. They quickly installed the equipment, confirmed its effectiveness, and decided to adopt it. Later, after some time, they introduced a controller for automation. 【Details】 - Installed in the turn chute of the concrete block manufacturing plant - Lent the necessary number of units, confirmed effectiveness, and adopted the equipment - Introduced a controller for automation *For more details, please refer to the PDF document or feel free to contact us. *Our website features numerous case studies. You can check them out via the link below.

At the resin raw material manufacturing company, to promote discharge from the bunker, a "blow disk" was adopted near the discharge outlet located at the bottom of the silo (conical part, midway). This time, we were consulted about installing this equipment in the area opposite the discharge outlet, as the powder there was not moving and was piling up like a mountain, in order to effectively utilize the bunker’s volume. We communicated that completely eliminating the pile was difficult and presented a proposal for installation. It was later decided to implement the solution, and the results have improved to a level acceptable to the customer. [Overview] ■ Material: Resin powder (prone to clumping) ■ Bunker capacity: 200m3 * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them via the link below.

This is a case that was consulted by a representative from a resin product manufacturing facility, where the "Blow Disk" was introduced. They had been experiencing clogging issues in the screw discharge hopper for PET crushed material. Hitting the hopper did not help, and they reached out to try this equipment. After providing the material overview and hopper drawings, we offered advice on the installation position and lent them the product. With the air injection and vibration from this equipment, the test results were favorable. They decided to proceed with the installation. 【Overview】 ■ Hopper Size: 1200×1200 ■ Hopper Capacity: 2m3 ■ Discharge: Screw Feeder ■ Material: PET crushed material ■ Material Size: 10mm or smaller ■ Blow Disk Installation Position: 4 units on each of the two inclined surfaces * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies, which can be accessed via the link below.

This is a project from the engineering department of a chemical company. They are loading products from a bulk bag into a hopper, but the discharge from the hopper is unstable... It has become a rat hole, and they have tried using air knockers and vibrators, but with no effect... They mentioned that they usually tap it down with a bar. We proposed a solution using a controller with four solenoid valves, sequentially turning on the air to two blow discs at four locations. They decided to implement the "blow discs," and the results were as expected, very good. [Overview] ■ Material: Aluminum hydroxide powder ■ Hopper diameter: 1300φ ■ Discharge diameter: 150A * For more details, please refer to the PDF document or feel free to contact us. * Our website features numerous case studies. You can check them out via the link below.