エムシーアイエンジニアリング List of Products and Services

This device is a general-purpose digital input/output unit with a GPIB interface, equipped with a maximum of 24-bit input ports and a maximum of 32-bit output ports. Simple IN/OUT commands allow for monitoring of the input ports and control of the output ports. Additionally, this device can reproduce the functions of the older model "UIO-788GPB" through jumper settings. By closing the specified jumper, users can utilize the "788 ASCII mode" and "788 Binary mode," allowing them to incorporate the GPIB interface into their own products using this handshake signal. By reading/writing data from the host computer through GPIB, users can control and monitor devices (user circuits) connected on the terminal side.

• Other semiconductor manufacturing equipment
• Other environmental equipment
• Other measurement, recording and measuring instruments

This device is the successor to the old model "RLT-2116ENC" and is a mini power relay unit with a LAN interface. It is equipped with 16 relay contact outputs and a power supply for external circuits. The relays can be controlled ON/OFF via LAN from a host computer. The contact outputs are independently configured. LEDs for monitoring the relay operation status are mounted on the front. Additionally, a terminal block is located on the front of the device, allowing for easy wiring with a screwless terminal block that does not require crimp terminals. It has a built-in external power supply, allowing you to control high-power external relays with the relay contacts or use it as a power source for small DC motors. (If an external power supply is not needed or if you prefer something other than 24V, please contact us.)

• Other FA equipment

This device is the successor to the old model "PCR-2152ENC" and is an isolated digital input/output device with a LAN interface, equipped with 16 photo-coupler inputs and 16 relay contact outputs. The photo-coupler inputs use a type that does not require polarity selection, allowing for connection in either current sourcing or sinking configurations. The relay contact outputs can be selected via jumper settings to be either normally open or normally closed, providing flexibility for controlling external devices. The front panel is equipped with monitor LEDs that indicate the status of the 16 input signals and the operational state of the 16 relays. The rear panel includes a D-sub 37 (female) for input signals, a D-sub 37 (male) for output signals, an inlet for AC power input, a fuse holder, a GPIB connector, and a DIP switch for function selection. Internally, this device has a built-in DC 24V power supply for external circuits, which can be accessed from both the input and output signal connectors. (If an external power supply is not required or if you prefer a voltage other than 24V, please contact us.)

• Control Panel

Interface: Ethernet Input/Output: 40 bits Power Supply: +5V Size: 102W x 122L x 22H (excluding protrusions) I/F: 10BASE-T/100BASE-TX (Connector: RJ45)

• Other process controls
• Other network tools
• Embedded Board Computers

This device is a successor to the old model "RLT-2716GPC" and is a mini power relay unit with a GPIB interface. It is equipped with 16 relay contact outputs and a power supply for external circuits. The relays can be controlled ON/OFF via GPIB from a host computer. The contact outputs are independently configured. LEDs for monitoring the relay operation status are installed on the front. It complies with IEEE 488.1 and IEEE 488.2 standards, and the GPIB address can be set using the dip switches on the back. A terminal block is located on the front of the device, allowing for easy wiring with a screwless terminal block that does not require crimp terminals. Since it has a built-in power supply for external use, it can be used to control high-power external relays or as a power source for small DC motors. (If an external power supply is not needed or if you prefer a voltage other than 24V, please contact us.)

• Other FA equipment

This device is the successor to the old model "PCR-2752GPC" and is an isolated digital input/output device with a GPIB interface, equipped with 16 phototransistor inputs and 16 relay contact outputs. The phototransistor inputs use a type that does not require polarity selection, allowing for connection in either current sourcing or sinking configurations. The relay contact outputs can be selected via jumper settings to be either normally open or normally closed, providing flexibility for controlling external devices. The front panel is equipped with monitor LEDs that indicate the status of the 16 input signals and the operational state of the 16 relays. The rear panel includes a D-sub 37 (female) for input signals, a D-sub 37 (male) for output signals, an inlet for AC power input and a fuse holder, a GPIB connector, and a DIP switch for function selection. Internally, this device has a built-in DC 24V power supply for external circuits, which can be accessed from both the input signal connector and the output signal connector. (If an external power supply is not required or if you prefer a voltage other than 24V, please contact us.)

• Control Panel

This device is a general-purpose digital input/output unit equipped with a GPIB interface, featuring 24-bit input ports and 16-bit output ports. Simple IN/OUT commands allow for monitoring of the input ports and control of the output ports. Additionally, this device can reproduce the functions of the older model "UIO-788GPB" through jumper settings. By closing the designated jumper, users can utilize the "788 ASCII mode" and "788 Binary mode," allowing them to incorporate the GPIB interface into their own products using this handshake signal. By reading/writing data to these input/output ports through GPIB from the host computer, users can control and monitor devices (user circuits) connected on the terminal side.

• Other semiconductor manufacturing equipment
• Other environmental equipment
• Other measurement, recording and measuring instruments

Mini Power Relay Unit with GPIB Interface 【Features】 ○ Equipped with 16 relay contact outputs and 7-bit status inputs ○ Can control 16 relays ON/OFF and monitor status inputs on the terminal side via GPIB from the host computer ○ Contact outputs can be selected by the user as make/break contacts ○ There is a signal to monitor the operating state of the relay, and in the case of RLY-5416GPC, an LED is implemented ○ Two modes are available: ASCII mode and binary mode, which can be switched using dip switches ○ Complies with IEEE 488.1 and IEEE 488.2 standards, and the GPIB address can be set using dip switches ○ RLY-5416GPC has a built-in power supply and operates on AC 100V

• Other process controls
• Other semiconductor manufacturing equipment
• Other laboratory equipment and containers

Interface: Ethernet Input/Output: 16-bit Power Supply: +5V Size: 102W x 60L x 22H (excluding protrusions) I/F: 10BASE-T/100BASE-TX (Connector: RJ45)

• Other process controls
• Other network tools
• Embedded Board Computers