Exhibiting at the 【TIC】 online exhibition platform.

Tilt the two air knives slightly and present a blowing method that focuses on the body and upper part.

The gap or slot of the air knife can be adjusted in length to allow for a wider gap. This means that the air knife, which is concentrated on the body, can maintain a standard gap while separately adjusting the knife gap at the top and bottom to hit the handle and the lower ring. This method not only allows the wind to effectively hit the body of the canister but also reduces the required power consumption. SONIC has also suggested further cost reduction by switching from plated steel pipes to ABS piping to lower prices even more. [Contents] [Issues] ○ Yankee Gas faced the problem of propane gas canisters not being sufficiently dry before going to the painting process while changing their solvent-based painting system. ○ Proper drying of the canisters is essential for effective painting. ○ The drying method they were using involved compressed air, which was ineffective and did not adequately remove moisture for painting. ○ High humidity means that no matter how much compressed air is applied, moisture remains on the canisters. For more details, please contact us or download the catalog.

• nozzle
• Pneumatic Equipment
• Drying Equipment

There was no need for additional construction, and it fit into the existing production line.

Sonic Corporation decided to operate the Sonic150 with 25 horsepower and two air knives, and to circulate air to raise the temperature coming from the air knives. The concept behind Sonic Corporation's revolutionary VT (patent pending) design is to utilize the pressure heat from the blower by partially circulating air. The exit temperature from the air knives will be approximately 45°C to 50°C. This method does not require an external thermal system. The air knives are installed about 10mm away from the bottles, allowing the bottles to pass through at a wind speed of approximately 9,300m/min. The high-speed air and heated exit temperature melt the ice and turn the remaining moisture into a mist. As a result, the bottles can be completely dried. [Content] [Issues] ○ Moisture and cold air leave water droplets on the glass, resulting in the reformation of water droplets before labeling. ○ Labels cannot be applied until the bottles are dried. ○ The injection and labeling of bottles require empty bottles to be stacked in a heated warehouse, and this process can only occur after they have been warmed. For more details, please contact us or download the catalog.

• nozzle
• Pneumatic Equipment
• Drying Equipment

I have made it possible to repeatedly position the air knife.

We proposed 12 Sonic 70 blowers with 7.5 horsepower motors, enclosures, Sonic HEPA filters, and two custom Sonic XE air knives measuring 13 inches. The performance of the air knives delivered at the beginning of this system perfectly matched the blow level requested by the customer. The results of the contamination test also confirmed that Sonic's HEPA filters maintained the requested 0.3μ. Additionally, to operate most effectively while keeping the noise level below 80dB, the angle and distance of the air knives are very important, so we manufactured custom Sonic air knives to fit the existing air knife enclosures, allowing for repeated positioning of the air knives. [Content] [Issues] - Compressed air with HEPA filters - The factory was using more compressed air for automatic devices on the production line and other equipment on a daily basis. - They were compelled to add another air compressor to avoid pressure drops due to increased demand for compressed air. For more details, please contact us or download the catalog.

• nozzle
• Pneumatic Equipment
• Drying Equipment

It has been proven to be the most cost-effective solution.

Sonic Corporation proposed an arrangement to blow a rotating air knife (patented) from above and a standard air knife from the side, positioned diagonally from top to bottom. Due to the low production speed and the complex shape of the engine block, it has been proven that the rotating air knife is suitable. The rotating air knife can achieve a rotation speed of 200 rpm. By rotating the air knife and then blowing, it can deliver multiple high-impact blows to the surface of the parts with a single air knife. In cases of such complex shapes, attempting to achieve the same drying with other methods would require the installation of six air knives. This technology has proven to reduce horsepower and provides the most cost-effective solution while utilizing limited space. [Content] [Issues] - The surface of the engine block has many complex irregularities, and if water remains in these areas, it can ultimately lead to defective products. - The factory has found existing drying methods to be inefficient and is seeking urgent solutions. For more details, please contact us or download the catalog.

• nozzle
• Pneumatic Equipment
• Drying Equipment

Non-contact water removal and drying of wire cables using Sonic Corporation's blower and air knife.

We would like to introduce a successful application of the Sonic SP Dryer cable drying machine. A manufacturer of low-voltage wires and cables, as well as bare aluminum and copper wires, needed to install a spark tester before the final packaging process. This meant that the wire, running at 3000 feet per minute (900 m/min), had to be completely dried before the spark test. Due to the rapid increase in line speed, traditional methods became costly and inefficient. If the cable is not completely dried, the inspection machine may misidentify it as defective. Because of the high-speed production at 3000 feet per minute (900 m/min), Sonic recommended the SP dryer. This is a drying device housed in a box that features energy-saving air knife technology (XE 42” long) with a centrifugal blower (Sonic 150, 20 horsepower). For more details, please contact us or refer to our catalog.

• nozzle
• Pneumatic Equipment
• Drying Equipment

Using it before the final drying provided results that exceeded expectations in terms of drying effectiveness.

Sonic Corporation's 96” (2.44m) air knife operates with the Sonic 100 (15 horsepower motor). Long steel plates flow under the air knife at speeds of 1.22m/min to 3.05m/min. The widths of these steel plates range from 48” to 96” (1.22m to 2.44m). Typically, this line runs for several days in two shifts and then stops for several days. Essentially, it operates continuously without stopping during the given shifts. This system provides unparalleled satisfaction to customers and has achieved exceptional drying effects when used before final drying to blow away a significant amount of residual water. [Content] [Issues] ○ After blasting the material, it needs to be wiped and all remaining sand particles must be completely blown away. ○ In special cases, residual shot can occur that passes through the cleaning brush. ○ Residual shot material sticks to large electromagnetic components, making transportation hazardous. For more details, please contact us or download the catalog.

• nozzle
• Drying Equipment
• others

"Sonic" drying is Sonic! We are introducing success stories and photos. [Simplified version]

This is a case study collection of Sonic Corporation's blower air knife systems. As success stories, we introduce how the Sonic air knife system provided technical solutions to issues such as labeling problems, removal of residues in the steel industry [removal of residues on plates], drying of automotive cylinders, insufficient drying of propane gas cylinders, and removal of residual water after cleaning contact lens pallets. We also present photographs. For more details, please contact us or refer to the catalog. We also have demo units available. You can try them in your factory! Alternatively, we can conduct simple tests at our company! Please consider it!

• Drying Equipment

"Sonic" water drainage drying is Sonic!! We are introducing case studies, conceptual installation diagrams, and photos.

This is a case study of Sonic Corporation's blower and air knife systems. As success stories, we introduce how the Sonic air knife system provided technical solutions to issues such as labeling problems, removal of residues in the steel industry [on plates], drying of automotive cylinders, insufficient drying of propane gas cylinders, contamination of fine particles due to static electricity in clean rooms, and removal of residual water after cleaning contact lens pallets. We also present conceptual installation diagrams and photos. For more details, please contact us or refer to our catalog. We also have demo units available. You can try them at your factory! Alternatively, we can conduct simple tests at our company! Please consider it!

• Drying Equipment

A product that suppresses water splashing generated during the inspection, printing, labeling, and water drainage/drying of filled PET bottles, cans, bottles, and pouches before packaging.

The Sonic SMART Tunnel is a versatile water drainage drying system. It is a turnkey product designed to dry PET bottles, cans, and jars before inspection, printing, labeling, or packaging, with a processing capacity of 100 to 1500 CPM. Adaptability: The Sonic SMART Tunnel is a modular system. Due to its bolt-on design, it can be easily expanded if changes in product size or additional air knife configurations are needed due to increased production line demands.

• Beverage Production Equipment

Improved air knife of the traditional Tear Drop (tear-shaped) design! Enhanced blowing efficiency!!

■High-Speed XE Air Knife The Sonic Corporation's High-Speed XE Air Knife nozzle, further improved from the conventional Tear Drop shape, achieves excellent work efficiency. It efficiently laminarizes the air, resulting in minimal pressure loss and uniform blowing across the entire slot. One of its greatest features is that there are no control plates inside the air knife, allowing for uniform blowing from end to end. Additionally, it effectively draws in the surrounding air to create a powerful blow. We offer a wide variety of options for the number, position, direction, and length of the nozzle's piping installation. We also provide the world's only rotary air knife.

• Hydraulic Equipment

A specialized blower for draining/drying that uses a small motor to spin at high speed and create a large airflow!

Powerful air at over 25 m/s for water removal and drying! Furthermore, time-saving and energy-efficient! Sonic Corporation's "Blower & Air Knife" is a device that dramatically improves the efficiency of parts drying, food processing drying, and blowing away water droplets. Processes requiring 400 kPa of pressure can be achieved with an ultra-high efficiency of just 29 kPa! While achieving a 75% reduction in energy compared to compressed air, the water removal efficiency exceeds 95%, resulting in significant energy savings. ≪Sonic Corporation's Spiral Blower≫ 【Features】 ■ Lightweight and compact design ■ Generates a large volume of air with a small horsepower ■ Clean and dry air. Promotes evaporation with warm air at approximately 40°C ■ Energy-saving effects that greatly exceed those of compressors △▽△Basic Information△▽△ 【Product Lineup】 ■ Spiral Blower Using unique technology, it generates a large volume of air with energy efficiency compared to compressors and conventional blowers. The generated large volume of air can be supplied continuously without pulsation. The structure is also easy to maintain.

• Pneumatic Equipment

Blow away water, dust, and dirt from parts with high-speed air and dry quickly. Demo units are also available for loan!

Water removal drying with Sonic Corporation's blower and air knife! By rotating the fan inside the blower at a minimum of approximately 12,000 rpm to 20,000 rpm, it is possible to achieve a larger airflow than compressors or domestic blowers. Additionally, one of the greatest features of the Sonic air knife system is that it is very economical, consuming only a fraction of the power compared to similar operations using conventional compressed air. Environmentally, it not only operates at low noise levels but also contributes to the reduction of carbon dioxide emissions due to its low power consumption. Demo units are available for loan, so please feel free to contact us. 【Demo Units】 ★ Unit 1 (Sonic 70) Flow rate: 3 Nm³/min to 13 Nm³/min Motor size: 5.5 kW *With inverter ★ Unit 2 (Sonic 85) Flow rate: 4 Nm³/min to 20 Nm³/min Motor size: 7.5 kW *With inverter ★ Air Knife Total length: 610 mm Maximum wind speed: approximately 170 m/sec Connection diameter: 3 inches Slit width: approximately 1 mm Note: Please contact us if you need a hose.

• Pneumatic Equipment

Sonic Corporation's blower and air knife use high-speed air of up to 25.4 m/sec for water removal and drying! Energy-saving blower! Demo units available for loan!

Are there any issues with the water drainage and drying processes for beverages, food, food processing, etc., or with blowing off water droplets from cans, bottles, and PET bottles? ------ Such problems can be efficiently and economically solved by the Sonic Air Knife System's high air volume and high-speed air! Tasks that previously required pressure like that of a compressor can now be achieved with just 29 kPa! When comparing the air volume of a compressor and a Sonic Blower, obtaining an air volume of 7 m³/min requires 62.5 horsepower with a compressor, while the Sonic Blower achieves this with only 4 horsepower. The difference is significant compared to compressors and domestic blowers! 【Features】 ● Energy-saving effect reduces consumption by 75% compared to compressor air ● Water drainage efficiency of over 95% ● Generates large volumes of air with low horsepower ● The air is clean and dry, promoting evaporation with warm air at about 40°C ● Energy-efficient (compared to compressors) ● Lightweight and compact design *Demo units are available for loan, so please feel free to contact us. Additionally, if you can provide samples, we will conduct tests at our company.

• nozzle
• Pneumatic Equipment
• Other drying equipment

By rotating the air knife, even complex shapes can be optimally drained/dried!

A rotary air knife that seems like it should exist but doesn't The Sonic Corporation's rotary air knife (patented) has been developed for draining (blow-off) and drying parts with complex shapes. The gaps in the air knife are angled at 15° relative to the rotating axis, allowing it to eject high-speed air while changing the blowing surface at regular intervals for the areas that require draining or drying. This effectively drains and dries the uneven surfaces and sides of the workpiece, as a single air knife passes over the workpiece multiple times. The rotary air knife can reduce energy costs compared to draining/drying done by multiple air knives. Additionally, it saves space since the installation of multiple air knives is unnecessary.

• Pneumatic Equipment

Seeing is believing! Improve drying and reduce running costs by using a high-speed air knife to blow off air discharged from a high-volume blower!

Is there any problem with the Sonic food processing drying process and the blowing off of water droplets from cans/bottles? After sterilization and filling, it is also used for draining water before printing expiration dates on PET bottle caps, cans, retort packs, and for drying transport boxes. It is utilized in various industries, not only in the food industry but also for draining and drying automotive parts, steel plates and pipes, and semiconductor components. The Sonic Air Knife System's high airflow and high-speed air efficiently and economically solve these problems! For those who have not been able to resolve issues until now… we have numerous case studies for problem-solving! ***Videos will be updated regularly*** [Case Studies] - Examples for the food/beverage industry - Examples for the automotive industry - Examples for the pharmaceutical industry - Examples for the steel industry, etc. For more details, please contact us or download the catalog.

• nozzle
• Pneumatic Equipment
• Hot air dryer

Sales of the "VT Tank Dryer," which incorporates a patented mechanism from Sonic Corporation's blowers, have begun.

The "VT Tank Dryer" is a product that incorporates a mechanism to raise the temperature of air circulated by a blower without using heating heaters or heat sources. It is designed for drying tanks, mixing machines, tote tanks, and piping up to 500 cubic feet (14.16 m³) after liquid cleaning. This device forces a reduction in the time typically spent on natural drying or manual cleaning and drying processes. Time reduction = energy savings Time reduction = labor cost reduction Additionally, it is safe.

• Drying Equipment
• Other drying equipment
• Hot air dryer

Spraying fine particles without pressure! Atomization through the vibration of piezoelectric ceramics!! Low power consumption and low energy costs!!

Ultrasonic waves generated by piezoelectric ceramics are transmitted to the spray nozzle (atomizer), where they vibrate the liquid film to create extremely fine particles for spraying. Liquid can be supplied and sprayed into fine particles without the need for pressurization. The flow rate varies depending on the model, but it can accommodate a wide range from a minimum flow rate of 10 ml/min to a maximum of 100 ml/min. Since pressure is not applied to the liquid, there is very little splatter or rebound, eliminating waste of the applied liquid. Additionally, there is no need for a large painting booth. This achieves a reduction in capital investment and running costs. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia Corporation.

• Ultrasonic Oscillator
• nozzle
• valve

Designed for ultra-low flow rates of 1 ml/min or less.

The stainless steel micro feed tube made by Sonia is designed for extremely low flow rates of less than 1 ml/min. *Of course, it can also be used at flow rates above 1 ml/min. The liquid flows through without touching the tip, which forms a uniform particle size. *This product is an accessory specifically for Sonia's ultrasonic spray nozzle.

• nozzle
• spray
• others

A new challenge with the Sonia Corporation's low-flow ultrasonic spray nozzle!

Low Flow Ultrasonic Spray Nozzle (Atomizer) The low flow spray nozzle (atomizer) manufactured by Sonia is designed to apply droplets (particles) of various viscosities in micron and submicron sizes without over-applying them to small parts. The nozzle shape comes in two types: flat and wide nozzle tips. It is suitable for concentrated application using an ultrasonic spray nozzle and a pinpoint air transport fixture (custom order), as well as for transporting very small droplets (particles). These spray nozzles can be easily applied to applications where coating control and uniform film are required. The spray nozzle is lightweight and ideal for coating systems using robots. The main body of the spray nozzle is made of stainless steel. *Custom micro feed tubes are suitable for low flow application and are available in stainless steel or PTFE fluororesin. The spray nozzle can be equipped with a spray shaper for pinpoint spraying or a wider spray for better coating control. *Micro feed tubes are optional.

• nozzle
• Other machine elements
• Other physicochemical equipment

A fixture for spreading wider than a wide-angle air transport fixture.

Dove Tail Spray Shaper The Dove Tail Spray Shaper is an air transport fixture, ideal for wide-angle spraying and flux coating. It can be used with all spray nozzles of NS and WS types. By changing the position of the Dove Tail Spray Shaper, it is possible to switch from a fan-shaped spray pattern to an elliptical spray pattern. *This product is a dedicated accessory for the ultrasonic spray nozzles manufactured by Sonia Corporation.

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

Designed for fluids that have a strong impact on stainless steel, such as pharmaceutical-related applications.

The Sonia Corporation's PTFE fluoropolymer microfeed tube is designed specifically for fluids that have a strong impact on stainless steel, particularly for pharmaceutical-related applications. The liquid must be completely isolated for reasons of hygiene and chemical reactions. *This product is an accessory specifically for Sonia Corporation's ultrasonic spray nozzle.

• nozzle
• Water Hydraulic Equipment
• others

A fixture for applying particles sprayed from an ultrasonic spray nozzle over a wide area.

The wide-angle air transport fixture is a device that uses gas or air to expand the spray angle. The wide-angle air transport fixture can be attached to the Narrow Spray models 60K50T and 130K50T. There is an air supply port on the side of the wide-angle air transport fixture. By injecting gas or air, the gas or air circulates inside, causing the particles sprayed from the ultrasonic spray nozzle to spread and be pushed out. By adjusting the gas volume, air volume, pressure, and the tip of the ultrasonic spray nozzle, a spray angle of up to approximately 100° can be achieved. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia.

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

The Sonia Corporation's ultrasonic particle size generator transforms liquids into fine particles!

The ultrasonic particle generator transforms low-viscosity liquids into fine particles. Our company's compact 2.4MHz NO model 241T uses a Teflon-coated nebulizer. This device is fully microcontroller-based, allowing users to program operating parameters while handling various applications for actual particle generation. The front panel is equipped with an LCD that enables users to vary the particle generation rate from 0% to 100% in 5% increments. For special processes, such as applying small parts, a device is incorporated that can adjust the flow rate between 0-2 cfm to move particles out of the vessel where they are created. This air source and all other connections feature easily removable 304SS fittings and Teflon O-rings, allowing for easy adaptation to cleaning, external gas supply, or vacuum connections. The 304SS Tee (also available with Teflon coating) is designed to trap particles, with a small amount of airflow/gas/vacuum used to move particles from the device.

• Ultrasonic Oscillator
• Other physicochemical equipment
• others

Flow spray of 2 mmlit/min or less is possible!

Sonaer low-flow spray nozzle manufactured by Sonia Co. It can focus on small parts without waste by creating micron and sub-micron particles. There are two types of nozzles: flat and wide spray tips. These nozzles are ideal for pinpoint spray shaping, focusing particles and minimizing solution waste. With these nozzles, coating control becomes possible, easily adapting to applications that require thin and uniform application. This nozzle is lightweight, making it attractive for use in robotic coating systems. The nozzle comes in a lightweight black aluminum case (custom-made) or a stainless steel case with a stainless steel inner feed tube. The micro feed tube can be used for microliter capacities and is available in stainless steel and PTFE. The nozzle can utilize a spray shaper for pinpoint spraying, allowing for better control of your coating applications.

• nozzle
• valve
• Etching Equipment

Designed to use fast-reacting liquids and capable of stirring in a short time!

The Sonia dual micro feed tube is designed to use fast-reacting liquids and can be stirred in a short amount of time. The material is stainless steel. The dual micro feed tube has two liquid supply ports, one at the top and the other on the side. *This product is a dedicated accessory for Sonia ultrasonic spray nozzles.*

• nozzle
• others

Air transport fixture for spraying in a square or rectangular shape.

This is an air transport device designed to spray particles from an ultrasonic spray nozzle in a square or rectangular shape. Its main application is for coating purposes. By adding a small amount of gas or air, it applies to square, rectangular, or flat substrates. By adjusting the distance from the workpiece and the pressure of the transport gas or air, various sizes and shapes of spray patterns can be achieved with the ultrasonic spray nozzle manufactured by Sonia. *This product is a dedicated accessory for the ultrasonic spray nozzle made by Sonia.*

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

It precisely sprays fine particles!

The pinpoint air transport fixture generates high-quality, fine particles and can uniformly apply them to medical coatings and other small precision devices. The spray speed is slow, making it suitable for applying expensive chemicals in a thin layer with minimal use. It excels not only in coating and manufacturing applications for medical precision instruments but also in uses such as stent coating and catheter coating, providing excellent reproducibility of spray speed and particle diameter, while significantly reducing the consumption of the coating agent. *This product is a dedicated accessory for the ultrasonic spray nozzle manufactured by Sonia Corporation.*

• nozzle
• Other physicochemical equipment
• Other surface treatment equipment

It is a subcutaneous solvent delivery device that can coat evenly and thinly.

Sonia's hypodermic needle spray attachment allows for precise and uniform thin coating, generating high-quality fine particles in a relatively narrow range. It is suitable not only for improving biocompatibility and drug delivery but also for preventing restenosis and thrombosis. It prevents clogging, provides uniform film thickness and density with low-speed application, and reduces wasteful coating. *This product is a dedicated accessory for Sonia's ultrasonic spray nozzle.*

• Ultrasonic Oscillator
• nozzle
• spray

The air nozzle manufactured by Lechler, affectionately known as the Multi-Channel Jet (combining low noise, energy efficiency, and high functionality).

In many industries and factories, work using compressed air has become essential. Air is utilized in various fields such as cleaning, blowing off, drying, and conveying. When air pressure is not controlled, annoying noise caused by high frequencies often occurs, leading to problems. This noise is due to turbulence at the air outlet of the nozzle, and its intensity is related to the shape of the nozzle orifice and the air pressure. Therefore, the higher the air pressure, the greater the harmful noise, which in turn increases the amount of air used, making it uneconomical. Lechler's multi-channel jet (air nozzle) significantly reduces noise levels while featuring high blowing power and low air consumption. The multi-channel jet is based on dividing the airflow into several air jets. The 116-hole orifice, designed to optimize airflow conditions, creates particularly uniform and straight powerful air jets. For more details, please contact us or refer to the catalog. You can download the English version of the catalog. *Lechler GmbH is a German spray nozzle manufacturer.

• nozzle

The noise level has decreased by about 60%! This air nozzle can be used not only in general industries but also in food service and healthcare.

Lechler multi-channel jet (air nozzle) A new low-noise flat jet nozzle has been introduced for the multi-channel jet! When replaced with a 4mm pipe, the noise level is reduced by approximately 60%. Air consumption can also be reduced by about 33%. The new air nozzle 'FL-600SY' is suitable for draining water, blowing away debris, and drying in very narrow spaces with flat air. By using SUS-316L material, it has become a product that can be used not only in general industry but also in food service and medical applications. ◆ For product details, please refer to the catalog or contact us. *Lechler GmbH is a German spray nozzle manufacturer.

• nozzle
• Pneumatic Equipment
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to any desired location for blowing freely and can be used over a wide temperature range of -30°C to 80°C. This product comes equipped with the FL-600H multi-channel jet (air nozzle). * The current model has an orange tip on the flexible hose and a dark blue body. * The thread standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• hose
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with a multi-channel jet (air nozzle) FL-600E. * The current model has an orange tip on the flexible hose and a dark navy connector. * The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• hose
• nozzle

Freely and precisely fixed to the blow area.

Multi-channel jet (flexible hose) Material: Polyacetal resin The flexible hose can be fixed to the desired blowing area freely and can be used in a wide temperature range from -30°C to 80°C. Dedicated flexible hose for Lechler's multi-channel jet (air nozzle) Can be connected to 1/4" male thread. *Lechler GmbH is a German spray nozzle manufacturer. *The current product has an orange tip and a dark blue body. *The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• hose
• nozzle

Best-selling Rehiller air nozzle FL-600E's sister product, ultra-compact round type, made of stainless steel SUS316L (5mm type).

Lechler multi-channel jet (air nozzle) The air emitted is laminar, allowing not only for powerful impact force but also for reduced noise levels. Additionally, by utilizing laminar flow, the amount of air consumed can also be minimized. In other words, it is an energy-saving product. The blow pattern is straight (7mm wide). *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehiller air nozzle FL-600E's sister product, ultra-compact round type, made of stainless steel SUS316L (4mm type).

Rehira's multi-channel jet (air nozzle) allows for laminar airflow, which not only provides powerful impact force but also reduces noise levels. Additionally, by utilizing laminar flow, it can also minimize air consumption. In other words, it is an energy-saving product. The blow pattern is straight (7mm width).

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehiller air nozzle FL-600E's sister product, small round type.

Lechler multi-channel jet (air nozzle) The air emitted is laminar, which not only provides powerful impact force but also reduces noise levels. Additionally, by maintaining laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehira air nozzle FL-600E's sister product, round type, made of zinc material.

Lechler multi-channel jet (air nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the bestselling Rehiller air nozzle FL-600E, round type.

Lechler multi-channel jet (air nozzle) The air emitted is laminar, which allows for minimal impact force and reduces noise levels. Additionally, by maintaining laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the best-selling Rehiller air nozzle FL-600E, offered in stainless steel 316L, wide type FL-600ST.

Lechler GmbH Multi-Channel Jet (Air Nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by maintaining laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. The Multi-Channel Jet model FL-600STW generates a very wide and powerful impact force. This nozzle is made of stainless steel 316L, allowing it to be used in high-temperature environments. The protruding tip of the nozzle prevents air from penetrating human skin. This nozzle complies with OSHA standards. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehira air nozzle, multi-channel jet series, flat type extra large.

Lechler multi-channel jet (air nozzle) The air blown out is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, it is possible to reduce the amount of air consumption. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehira air nozzle Multi-channel jet series flat type outlet two-phase type (FL-600FK sister product)

Lechler GmbH multi-channel jet (air nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehiller Company Air Nozzle Multi-Channel Jet Series Flat Type

Lechler multi-channel jet (air nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehiller Company air nozzle FL-600E's sister product, super large round type.

Rehira's multi-channel jet (air nozzle) allows the ejected air to be laminar, which not only provides powerful impact force but also reduces noise levels. Additionally, by maintaining laminar flow, it can also minimize the amount of air consumed. In other words, it is an energy-saving product.

• nozzle
• Pneumatic Equipment
• nozzle

Best-selling Rehiller Company Air Nozzle Multi-Channel Jet Series Flat Type

Rehira's multi-channel jet (air nozzle) allows for laminar flow of the expelled air, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product.

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the bestselling Rehiller air nozzle FL-600E, offered in stainless steel 316L.

Multi-channel jet (air nozzle) manufactured by Rehira The air blown out is laminar, which allows not only for minimal impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. This is an air nozzle made of stainless steel 316L, a sister product of the FL-600E. Being made of stainless steel allows for use in high-temperature environments, while also providing a powerful impact force.

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the best-selling Rehiller air nozzle FL-600E, made of PP material.

Lechler multi-channel jet (air nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by maintaining laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the bestselling Rehiller air nozzle FL-600E, a type with half the spray width.

Lechler GmbH multi-channel jet (air nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumed during use can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the best-selling Rehiller air nozzle FL-600E, offered in aluminum material.

Lechler multi-channel jet (air nozzle) The air emitted is laminar, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumption can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German spray nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

Sister product of the best-selling Rehiller company's air nozzle FL-600E, offered in POM without pigments.

Lechler multi-channel jet (air nozzle) The air emitted is laminar flow, which not only minimizes impact force but also reduces noise levels. Additionally, by achieving laminar flow, the amount of air consumption can also be minimized. In other words, it is an energy-saving product. *Lechler GmbH is a German nozzle manufacturer.*

• nozzle
• Pneumatic Equipment
• nozzle

World's One, Air Nozzle with Orifice Cover - An air nozzle that achieves strong impact force with laminar flow - One of the best-selling products.

Rehiler Multi-Channel Jet (Air Nozzle) ≪Product Features≫ The air emitted is laminar (well-structured airflow), which allows for not only minimal impact force but also reduced noise levels. Additionally, by maintaining laminar flow, the amount of air consumed is minimized, and even with reduced pressure, the impact force does not decrease. In other words, this product contributes to energy savings and noise reduction. The blow pattern is straight (47mm width). ≪Significant Differences from Other Products≫ This product comes with an orifice cover (discharge hole adjustment plug). By using the orifice cover, it is possible to adjust the necessary air holes and suppress unnecessary air, making it a world-class product. ≪≪For Energy Savings, High Efficiency, and Noise Problem Solutions!≫≫ - Is the impact force sufficient? - Have you resolved the noise issues generated by the air nozzle? - Is the material suitable for use in food, medical, and pharmaceutical applications? The Rehiler Multi-Channel Jet is here to solve those concerns. Only Rehiler provides a catalog that includes impact force, noise levels, air consumption (energy-saving measures), and blow patterns!

• nozzle
• Pneumatic Equipment
• nozzle

What is "one stone, three birds"? It refers to an air nozzle that, while being low noise (quiet) and reducing air consumption (energy-saving), also has a strong impact force (high functionality).

Air nozzle created by a long-established European manufacturer. Only Lechler provides information on impact force, noise level, air consumption (energy-saving measures), and blow pattern in their catalog! In various industries, air plays an extremely important role in processes such as drying, cooling, conveying, blowing off, cleaning, mixing, and opening packaging bags. There is no doubt that the use of air contributes to improving the economic efficiency of production processes, and its applications still have no limits. However, air production incurs significant costs, and during use, it generates high-frequency noise that adversely affects the hearing of workers. Therefore, air nozzles that consume as little air as possible and operate at low noise levels are required. Lechler will leverage all accumulated nozzle technology and years of experience and achievements to solve this problem. ■□━━━━━━━━━━━━━━━━━・・・・・‥‥‥……… For details on each product, please download the catalog or feel free to contact us. ・・・・・‥‥‥………━━━━━━━━━━━━━━━━━■□ *Lechler GmbH is a German spray nozzle manufacturer.

• nozzle
• Pneumatic Equipment
• Drying Equipment and Devices

Best-selling Rehiller Co. air nozzle FL-600E's sister product, round type, offered in brass.

Rehira Multi-Channel Jet (Air Nozzle) Material: Brass Impact Force: 2.1N @ 0.2MPa Noise Level: 79 dB (A) @ 0.2MPa Flow Rate: 18N?/h @ 0.2MPa Maximum Operating Pressure: 1MPa Heat Resistance: 200℃ *Please refer to the catalog for mounting screws, dimensions, and spray width. = Features = - Quiet operation (compared to half-moon single outlet nozzle (copper pipe and crushed): approximately 12 dB (A) reduction) - Low air consumption (approximately 30% reduction possible for the intended purpose) - Pressure loss within the air nozzle (approximately 6%) = Approval Standards = - OSHA (Occupational Safety and Health Administration [Noise])

• nozzle
• Pneumatic Equipment
• nozzle

Freely and precisely fixed to the blow area.

Multi-channel jet (flexible hose) Material: Polyacetal resin The flexible hose can be fixed to the desired blowing area freely and can be used in a wide temperature range from -30°C to 80°C. Dedicated flexible hose for Lechler's multi-channel jet (air nozzle) Can be connected to 1/4" male thread. *Lechler GmbH is a German spray nozzle manufacturer. *The current product has an orange tip and a dark blue body. *The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Fixed precisely at the blow area freely and effortlessly.

Multi-channel jet (flexible hose) Material: Polyacetal resin The flexible hose can be fixed to the desired blowing location, allowing for versatile use within a wide temperature range of -30°C to 80°C. Dedicated flexible hose for Lechler multi-channel jets (air nozzles) Can be connected to 1/4" male threads. *Lechler GmbH is a German spray nozzle manufacturer. *The current product has an orange tip and a dark blue body. *The thread standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Multi-channel jet (flexible hose) Material: Polyacetal resin The flexible hose can be fixed to the desired blowing location, allowing for versatile use within a wide temperature range of -30°C to 80°C. Dedicated flexible hose for Lechler multi-channel jet (air nozzle) Can be connected with 1/4" male thread. *Lechler GmbH is a German spray nozzle manufacturer. *The current product has an orange tip and a dark blue collar. *The thread standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• Pipe Fittings
• nozzle

Freely and easily fixed to the blow area in a pinpoint manner.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600E. * The current model has an orange tip on the flexible hose and a dark blue connector. * The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired blowing area and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600E. * The current model has an orange tip on the flexible hose and a dark blue body. * The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600E. * The current model has an orange tip on the flexible hose and a dark blue body. * The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired blowing area and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600H. *The current model has an orange tip on the flexible hose and a dark blue connector. *The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the FL-600H multi-channel jet (air nozzle). * The current model has an orange tip on the flexible hose and a dark blue connector. * The thread standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600H. *The current model has an orange tip on the flexible hose and a dark blue body. *The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600R. * The current model has an orange tip on the flexible hose and a dark blue connector. * The thread standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• Pipe Fittings
• nozzle

Freely and easily fixed to the blow area in a pinpoint manner.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the multi-channel jet (air nozzle) FL-600R. * The current model has an orange tip on the flexible hose and a dark blue connector. * The screw standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose, which can be fixed to the desired blowing area, can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with the FL-600R multi-channel jet (air nozzle). * The current model has an orange tip on the flexible hose and a dark blue connector. * The screw standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to any desired location for blowing freely and can be used over a wide temperature range of -30°C to 80°C. This product comes equipped with a multi-channel jet (air nozzle) FL-600R. *The current model has an orange tip on the flexible hose and a dark blue body. *The screw standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes with the multi-channel jet (air nozzle) FL-600M already installed. * To attach the FL-600M to the flexible hose, a 1/8" PF female x 1/4" PF male fitting is required. * The current product has an orange tip on the flexible hose and a dark blue collar. * The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired area for blowing freely and can be used in a wide temperature range from -30°C to 80°C. This product comes equipped with a multi-channel jet (air nozzle) FL-600M. * To attach the FL-600M to the flexible hose, a 1/8" PF female x 1/4" PF male fitting is required. * The current product has an orange tip on the flexible hose and a dark blue collar. * The thread standard on the piping connection side is PT (the nozzle connection side is PF).

• nozzle
• Pipe Fittings
• nozzle

Freely and precisely fixed to the blow area.

Material: Polyacetal resin The flexible hose can be fixed to the desired blowing area and can be used in a wide temperature range from -30°C to 80°C. This product comes with the multi-channel jet (air nozzle) FL-600M pre-installed. * To attach the FL-600M to the flexible hose, a 1/8" PF female x 1/4" PF male fitting is required. * The current product has an orange tip on the flexible hose and a dark blue collar. * The thread standard on the piping connection side is PT. (The nozzle connection side is PF.)

• nozzle
• Pipe Fittings
• nozzle

Cost reduction! A lineup of "low noise + energy-saving + high-performance" air nozzles approved by OSHA, FDA, and EC No. 1935/2004.

Only Reihler Corporation includes impact force, noise level, air consumption (energy-saving measures), and blow patterns in their catalog! In various industries, air plays an extremely important role in drying, cooling, transporting, blowing off, cleaning, mixing, and opening packaging bags. There is no doubt that the use of air contributes to improving the economic efficiency of production processes, and its applications still have no limits. However, air production incurs significant costs, and during use, it generates high-frequency noise that adversely affects the hearing of workers. Therefore, air consumption must be minimized, and air nozzles that operate at low noise levels are required. Reihler Corporation will leverage all accumulated nozzle technology, along with years of experience and achievements, to solve this problem. Additionally, we are always available for consultation for users who need solutions in special cases. Our products are also approved by OSHA, FDA, and (EC) no. 1935/2004. ■━━━━━━━━━━━━━━━━━ For details on each product, please download the catalog or feel free to contact us. ━━━━━━━━━━━━━━━━━■

• nozzle
• Pneumatic Equipment
• nozzle

The "24 Tissue Tubes 3.0ml Type" features a wide inner diameter of 13.4mm at the mouth, a low height of 25.9mm, and a flat bottom design, making it easy to insert and remove samples. Each tube is equipped with a 2D code on the bottom, allowing for efficient sample information management by using a 2D scanner to reflect the code in a PC database. Additionally, it is compatible with automated systems due to its SBS format. 【Features】 ■ Easy insertion and removal of samples ■ Particularly suitable for tissue/cell samples measuring 5mm to 7mm ■ Using our dedicated rack for 24 tubes allows for bulk reading of the 2D codes on the tube bottoms ■ Compatible with automated systems due to its SBS format ■ Made of polypropylene, autoclavable, and compatible with DMSO *For more details, please refer to the related links or feel free to contact us.

■Disadvantages of Conventional Antistatic Fluororesin Coatings - Requires high-temperature firing (around 400°C) - Applicable only to metals - Limited color options - Low mechanical strength ■Features of Safron LF+ - Can be processed at low temperatures (below 100°C) - Applicable to metals and resins - Color variations available - High friction coefficient and mechanical strength - Antistatic performance is equivalent to conventional Safron For more details, please check the product site.

The "Mechanical Stitching Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

The "Mechanical Stitch Method" by Nichinichisui Road Machinery Co., Ltd. is a new technique that allows for the repair of metal cracks without the application of heat. By using special bolts and reinforcement plates, cracks are physically removed, and repairs are made without causing any thermal impact to the base material. Repairs can be carried out in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. ◎ For more details, please contact us. ◎ If a detailed technical explanation is needed, please contact us.

<Title> Development of Gene Expression Control Technology through RNA Hacking In the latest presentation paper, we have utilized Abby. Associate Professor Yosuke Katsuta from Kumamoto University Graduate School of Advanced Science and Technology, Analytical Chemistry Laboratory (also co-founder of StapleBio), will be giving a presentation in an online seminar. He is working on the development of RNA hacking technology aimed at controlling gene expression by utilizing short nucleic acids named Staple to change the higher-order structure of target mRNA. He will present the latest data focusing on the results of cell experiments and animal experiments in the development of this technology. Related paper on the presentation content: Staple oligomers induce a stable RNA G-quadruplex structure for protein translation inhibition in therapeutics | Nature Biomedical Engineering