We have added an 800nm short pass filter to our expert coating.

It is an optical filter that selectively transmits light below a specific wavelength and blocks light with longer wavelengths.

The short pass filter selectively transmits light below a specific wavelength while blocking light of longer wavelengths. This allows for effective handling of light in a specific wavelength range. (Do you have any of the following concerns?) ■ Is it customizable due to its high wavelength dependence? ■ If light is incident at an angle, will performance decrease, and can it be controlled? ■ When blocking a specific wavelength, there may be a decrease in transmittance. ■ Can it cause chromatic aberration? ■ Is it difficult to control multiple wavelengths simultaneously?

• Other optical parts
• Color camera
• Sensors

This is a mirror that reflects near-infrared light, which causes heat. It has a proven track record in projectors and lighting devices where temperature rise is a concern.

1) Are you facing such issues? ■ I want to prevent the temperature from rising due to near-infrared light emitted from the light source. ■ Projectors and lighting devices are getting too hot. ■ Is it possible to transmit visible light while reflecting near-infrared (NIR)? ■ Can the wavelength range of the mirror be customized? 2) What is a hot mirror? A hot mirror is used in projectors and lighting devices where temperature rise due to infrared radiation is a concern. By using a hot mirror, it is possible to suppress temperature rise and enable bright light source design. As for the coating, it has a special coating that transmits visible light and reflects more than 95% of near-infrared light (NIR). It is used in lighting equipment that employs halogen or xenon light sources, as well as in light source reflection mirrors for medical devices.

• LED Module
• mirror
• Sensors

It is an optical filter that cuts ultraviolet and infrared light while having a high transmittance in the visible light range.

A UV-IR cut filter is a filter that cuts light in the ultraviolet and infrared regions while having a high transmission rate in the visible light region. In other words, it is an optical filter that simultaneously realizes the characteristics of both a UV cut filter and an IR cut filter. By placing it in front of CMOS sensors or CCD sensors, it serves multiple roles such as cutting noise light, providing heat protection against various light sources, and preventing degradation of liquid crystal components due to ultraviolet light. It is an excellent optical filter and optical thin film with multiple functions. Are you facing any of these issues? - Is it possible to cut both ultraviolet and near-infrared light? - Can a filter be made that allows visible light to pass while blocking IR and UV wavelengths? - I want to reduce noise light and increase sensor sensitivity. Can I consult about this? - Is it possible to customize the wavelength range that I want to transmit? - Is processing to chip size possible?

• Other optical parts
• Surveillance Cameras
• Sensors

It is a dielectric multilayer film filter that transmits visible light and reflects near-infrared light.

It is used as a near-infrared cut filter that adversely affects CCD devices such as video cameras. The optical characteristics, such as the wavelength position with a transmittance of 50%, transmittance, and cut wavelength band, can be set arbitrarily. (Are you facing such challenges?) Is it possible to cut only the wavelength of near-infrared light? I want to allow visible light to pass while blocking IR wavelengths. I want to suppress light that causes noise and increase the sensitivity of the sensor. Can the wavelength range I want to transmit be custom adjusted? Is it possible to process it to chip size?

• Other optical parts
• Color camera
• Sensors

The glass pot lid has a hydrophilic heat-resistant coating, allowing you to check the cooking state without any fogging.

SPACECOOL Co., Ltd. is pleased to announce its support for the purpose of the newly established memorial day "Day to End the Too Hot Summer" by the Japan Climate Leaders Partnership (JCLP). In order to address the increasingly severe heat waves, we will continue to promote the expansion of our zero-energy cooling radiative cooling material "SPACECOOL." JCLP has registered August 8, 2025, and every August 8 thereafter, as "Day to End the Too Hot Summer" with the Japan Anniversary Association. — What is the new memorial day "Day to End the Too Hot Summer"? In recent times, many regions in Japan have been experiencing consecutive days of extreme heat, and the impacts of climate change are manifesting in serious ways in our lives. Nevertheless, reports and discussions linking this to "climate change" are limited, and there is currently a lack of momentum for climate change measures. In response to this issue, JCLP has decided to establish the "Day to End the Too Hot Summer" during this hottest time of the year, creating a social impetus to reframe "heat" as a climate change issue. This memorial day aims to share the commitment to halt the climate crisis for future generations and serve as a starting point for advancing the systemic transformation of society as a whole.

Are you making progress on measures for the "2024 Problem"? With stricter management of drivers' working hours, reducing "waiting time" has become an urgent issue in the logistics field. To address this challenge, our company, Hotron, proposes the "Vehicle Detection Ultrasonic Sensor 'HM-UX2'," which instantly grasps the availability of loading bays. The 'HM-UX2' contributes to the resolution of waiting times by accurately understanding the availability situation, reducing unnecessary waiting and queueing, and shortening waiting times to alleviate the burden on drivers! By replacing the "eyes" of your loading bay management with this high-precision sensor, why not start addressing the "2024 Problem"? Take a look at the product features: "Can it accurately detect availability?" "Can we really use it in our company?" "I just want to know the cost, even if it's an estimate." If you have any questions or requests, please feel free to consult with us.

The following cameras are supported in the Elua 7.6 series. Product introduction: https://aileunsys.co.jp/b01_aileun.html Compatible camera list: https://aileunsys.co.jp/aileun/compatible_camera.html Newly added: - Manufacturer: DAHUA Model number (1 model): DH-IPC-HFW2449TLN-S-PRO

Dear Valued Customers, Thank you very much for your continued support. We would like to inform you that our company will be closed for summer vacation from Wednesday, August 13, 2025, to Friday, August 15, 2025. We will resume normal operations on Monday, August 18. We appreciate your understanding and cooperation.