Circular Economy News, September 9, 2024 Issue, Notice of Advertisements and Article Publications

You can easily tell if the liquid in the drum is full or empty with just one touch!

"Sensor-type Liquid Level Gauge for 200L Drums" GDB-CF / For Full GDB-CL / For Empty (For low-viscosity oil, kerosene, diesel, wastewater, and waste liquids) *Not suitable for solvents or chemicals that can damage materials. "Benefits" ● You can check whether the liquid inside the drum is full or empty without tilting the drum or peering inside, using each product. ● You can confirm when the drum is full or empty during liquid transfer. ● The sensor can be adjusted according to the desired liquid level line using a position adjustment adapter. ● Lightweight and affordable. ● Enables management of liquids inside the drum. ● Usable liquids include low-viscosity oil, kerosene, diesel, water, wastewater, and waste liquids. *Not suitable for solvents or chemicals that can damage materials. "Features" ● Dedicated to JIS standard 200L drums. *Can be attached to the small plug of the drum (G3/4). ● Confirmation work can be done within 3 minutes from startup (automatic stop after 3 minutes). ● The full and empty indicators light up in red and alert with a 15-second buzzer. ● Uses four AA batteries (approximately 1,000 uses). ● This product is for indoor use only. *Do not use outdoors.

• Other pumps

Reusing cutting fluids for machine tools and tank cleaning.

**APDQO Series** APDQO-FS (Stainless Steel Filter) APDQO-FF (Non-woven Fabric Filter) APDQO-FB (Bag Filter) ◎ Does not use electricity ◎ Automatically stops when full ◎ Equipped with a safety valve as standard **Benefits** ● Enables reuse of cutting fluid ● Improves tool life ● Safe with no electric leakage due to air drive ● Cleaning time as short as 5 minutes **Features** ● Designed specifically for JIS standard 200L open drums ● Capable of separating cutting fluid and chips ● Safety valve and float included as standard **Applications** The air-operated tank cleaning filtration cleaner APDQO-F series is capable of cleaning tanks of machine tools and filtering and separating both "liquids" and "solids." Therefore, in addition to filtering chips and sludge from machine tools, it can also be used for the following purposes: ● Cleaning machine tool tanks (removing chips and sludge and reusing cutting fluid) ● Separating and sorting food waste in wastewater at food processing plants (restaurants) ● Separating water and sludge from mountains and rivers ● Separating and sorting waste and sewage

• Filtration Equipment

Cutting fluids for machine tools can be reused! Tank cleaning time is significantly reduced!

**APDQO Series** APDQO-FF100 (Non-woven Fabric Filter) APDQO-FS100 (Stainless Steel Filter) APDQO-FB100 (Bag Filter) ◎ Does not use electricity ◎ Automatically stops when full ◎ Equipped with a safety valve as standard **Benefits** ● Enables reuse of cutting fluid ● Improves tool life ● Safe due to air drive with no electric leakage ● Cleaning time as short as 5 minutes **Features** ● Designed specifically for JIS standard 200L open drums ● Capable of separating cutting fluid and chips ● Safety valve and float included as standard **Applications** The air-operated tank cleaning filtration cleaner APDQO-F series is capable of cleaning tanks of machine tools as well as filtering and separating 'liquids' and 'solids'. Therefore, in addition to filtering chips and sludge from machine tools, it can be used for the following purposes: ● Cleaning of machine tool tanks (removal of chips and sludge and reuse of cutting fluid) ● Separation and sorting of food waste in wastewater at food processing plants (restaurants) ● Separation of water and sludge from mountains and rivers ● Separation and sorting of waste and sewage

• Filtration Equipment

Non-sticky! Refreshing, smooth mist. Ideal mist fan for heatstroke and static electricity prevention in areas where open flames are prohibited.

**Merits** - Maximum cooling of minus 8 degrees (−8℃) improves work efficiency in high-temperature and high-humidity environments - Continuous operation possible - Safe to use in explosion-proof areas as the power source is air - High water-saving function allows for usage while conserving water - By adjusting the valve opening, it can operate for about 8 hours on 1 liter **Features** - Dedicated container included as a substitute for the tank - Water supply tank compatible with large 10-liter types and servers - Circulator and oscillation function enable wide-area cooling, ventilation, and air blowing - Mist and airflow adjustment with a needle valve - Two types available, 18 type and 24 type, depending on the "site" or "application"

• Oil Mist Collector

For transferring low-viscosity oils such as kerosene, light oil, and biodiesel! Electric handheld pump.

**EMH Series** EMH-20FC (for oil, kerosene, diesel, biodiesel / pump only) EMH-20SUS (for oil, kerosene, diesel, biodiesel, solvents / pump only) EMHH-20FC (for oil, kerosene, diesel / both ends with hose) **Advantages** ● Continuous operation possible ● Can transfer kerosene and diesel without selecting containers ● Ideal for transferring biodiesel oil ● Low vibration and low noise **Features** ● Dedicated to JIS standard 200L closed drums (large cap G2) ● Equipped with a relief valve (0.1MPa), vane pump ● Various customizations available for drum cans and hose connections *Note: The SUS type cannot be used with water or solvents.* **Mechanism of EMH Pump** The center of the pump body is slightly offset from the center of the impeller, creating a structure where the movable vanes extend due to centrifugal force. It adopts a principle of operation that increases pressure by reducing volume with the vanes. Additionally, the EMH series uses Teflon and fluorine for the packing, allowing for the transfer of biodiesel.

• Other pumps

A heater that warms up drums and other containers to reduce the viscosity of liquids.

"HTJ Series" HTJ-A-P (for pails and one-gallon cans) HTJ-B-50D (for 50L drums) HTJ-C-100D (for 100L drums) HTJ-C-200D (for 200L drums) HTJ-HHD (for 200L drums) HTJ-HP2D (for 200L drums) HTJ-IBC1-40 (for IBC containers) HTJ-IBC2-90 (for IBC containers) ◎ Selectable by container type "Benefits" ● Completely covers the container, making it less likely to cool down ● Foldable, requiring less space for storage "Features" ● Compatible with 6 types of containers, temperature adjustment via dial ● Three types of outer covering material, simply wrap around the container and secure with a band <Common Specifications> Power Supply (V): 100 <Usable Liquids> - Oil - Water-based paint - Triethanolamine * Not suitable for flammable liquids. * The product shown in the video is from the time of filming. The design and specifications may differ at the current time or during the sales period. Thank you for your understanding.

• Other heaters
• Heater

Collecting cutting fluids, waste oil, and solvents such as IPA, methanol, and toluene in drums.

◎Explosion-proof specification that does not use electricity ◎Can be stored in a sealed manner ◎Compatible with high-viscosity liquids ◎Low failure rate 《Advantages》 ●Safely suction volatile and flammable liquids ●Cost-effective with low failure rates, reducing expenses ●Low air consumption, energy-saving ●Acceptable for small amounts of foreign matter contamination ●Continuous operation possible ●Automatic stop when full ●Easy adapter installation (bag nut type) 《Features》 ●Dedicated to JIS standard 200L closed drums (large cap G2) ●Sealed negative pressure type for suction only, discharge not possible ●Equipped with an anti-static grounding wire *Only for G and AS ●Built-in float ball for leak prevention 《Suction Mechanism》 1. Connect compressor air (air pressure 0.4 to 0.6 MPa) 2. Discharge externally from the ejector without entering the tank 3. Negative pressure is generated at the ejector, expelling air from the tank 4. The tank becomes negative pressure and sucks in external air 5. Liquid is suctioned from the suction nozzle 6. When the liquid is full, the float ball blocks the air discharge port, stopping suction

• Other pumps

Collecting cutting fluids, waste oil, and solvents such as IPA, methanol, and toluene in drums.

◎Explosion-proof specification that does not use electricity ◎Can be stored in a sealed manner ◎Compatible with high-viscosity liquids ◎Low failure rate 《Benefits》 ●Safely suction volatile and flammable liquids ●Cost-effective with low failure rates, reducing expenses ●Low air consumption, energy-saving ●Acceptable for small amounts of foreign matter contamination ●Continuous operation possible ●Automatic stop when full ●Easy adapter installation (bag nut type) 《Features》 ●Dedicated to JIS standard 200L closed drums (large cap G2) ●Sealed negative pressure type for drum cans, suction only, no discharge ●Equipped with an anti-static grounding wire (only for G and AS) ●Built-in float ball for leak prevention 《Suction Mechanism》 1. Connect compressor air (air pressure 0.4 to 0.6 MPa) 2. Discharge outside from the ejector without entering the tank 3. Negative pressure is generated at the ejector, expelling air from the tank 4. The tank becomes negative pressure and draws in external air 5. Liquid is suctioned from the suction nozzle 6. When the liquid is full, the float ball blocks the air discharge port, stopping the suction

• Other pumps

Collecting cutting fluids, waste oil, and solvents such as kerosene, light oil, gasoline, IPA, methanol, and toluene in drums.

◎Explosion-proof design that does not use electricity ◎Can be stored in a sealed manner ◎Compatible with high-viscosity liquids ◎Low failure rate 《Advantages》 ●Safely suction volatile and flammable liquids ●Cost-effective with low failure rates, reducing expenses ●Low air consumption, energy-saving ●Acceptable for small amounts of foreign matter contamination ●Continuous operation possible ●Automatic stop when full ●Easy adapter installation (bag nut type) 《Features》 ●Dedicated to JIS standard 200L closed drums (large cap G2) ●Sealed negative pressure type for suction only, not for discharge ●Equipped with an anti-static grounding wire (for G and AS only) ●Built-in float ball for leak prevention 《Suction Mechanism》 1. Connect compressor air (air pressure 0.4 to 0.6 MPa) 2. Discharge outside from the ejector without entering the tank 3. Negative pressure is generated at the ejector, expelling air from the tank 4. The tank becomes negative pressure, drawing in external air 5. Liquid is suctioned through the suction nozzle 6. When the liquid is full, the float ball blocks the air discharge port, stopping suction

• Other pumps

On September 15, 2026, we issued a press release regarding the wooden lightweight sheet "Hyper CLT Sheet." The Hyper CLT Sheet is a civil engineering sheet that utilizes CLT (Cross-Laminated Timber) stacked in an orthogonal direction. It can be used in various locations such as temporary roads, access routes, heavy machinery work yards, and material storage areas. The 5×10 version weighs approximately 230 kg, making it relatively lightweight and easy to install, remove, and relocate. Additionally, it offers environmental benefits such as reducing glare and metallic sounds typical of wood, as well as CO2 fixation. Furthermore, it can be proposed for the use of new technologies in public works as a **registered technology with the Ministry of Land, Infrastructure, Transport and Tourism "TH-250021-A."** Through this press release, we aim to expand the new wooden lightweight sheet that combines wood, NETIS, civil engineering, and CLT to more construction sites.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

The "HA-T Series" is an energy-saving automatic door sensor that opens only for those who wish to enter, whether on a busy street or in a narrow passageway. The automatic door opens simply by bringing your hand close, addressing hygiene concerns even in facilities used by a large number of people. You can choose between "Non-vision Mount Type/HA-T401" and "Non-vision Built-in Type/HA-T520" depending on the application and installation location. 【Recommended for such places!】 ☑ Entrance facing a busy corridor ☑ Presence of counters or signs near the door ☑ Buildings facing narrow passages ☑ Buildings that prioritize aesthetics ☑ Hospitals and facilities that consider hygiene ☑ Large facilities with many doors 【Features】 ● Adaptable to various door types with four detection spot settings ● Reduces unnecessary opening and closing, contributing to energy-saving by minimizing wasteful power consumption ● Equipped with a light touch function, allowing the door to open and close just by waving your hand, ensuring hygiene ● Can also be used as a wide detection range non-vision infrared sensor ◎ For more details, please download the materials or contact us.

Metal cracks are one of the concerns in equipment maintenance operations. Repairs using conventional welding methods often change the base material around the crack due to heat, leading to residual stress and deformation, which constantly carries the risk of "crack recurrence" and "secondary damage." Hinode Waterworks Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be carried out even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

Metal cracks are one of the concerns in equipment maintenance operations. Repairs using conventional welding methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" or "secondary damage." Hinode Waterworks Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be performed even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.