Smooth flow under high pressure: KNF announces new product FP 1.70.

Pulsation-reducing liquid pump, a high-output diaphragm liquid pump that significantly reduces pulsation generated during pump suction and discharge. Exhibiting at JASIS 2025.

We have reviewed the design of the pump itself as a liquid pump for pulsation reduction measures. Previously, pulsation reduction was achieved using dampers, but now the pump itself significantly suppresses pulsation. It features a high discharge specification. - FP1.7 Series / FP1.25 Series We have integrated the pulsation reduction damper with the pump. Two types are available: brushed DC motors and brushless DC motors. The brushless DC motor also allows for digital customization. We will be exhibiting at JASIS 2025, one of Asia's largest cutting-edge science and analysis systems & solutions exhibitions, where manufacturers of analytical and scientific instruments gather. Please visit our booth. We look forward to seeing you there. ■ Exhibition Name: JASIS 2025 ■ Date: September 3 (Wed) - 5 (Fri), 2025 (3 days) ■ Venue: Makuhari Messe International Exhibition Hall and Conference Center ■ Participation Fee: Free (Pre-registration required) ■ Booth Number: 6B-703

• Other pumps

Pulsation-reducing liquid pump, a diaphragm liquid pump that significantly reduces pulsation generated during pump suction and discharge.

We have reviewed the design of the pump itself as a liquid pump for pulsation reduction measures. Previously, pulsation reduction was achieved using dampers, but now the pump itself significantly suppresses pulsation. - FP7 Series / FP25 Series The pulsation reduction damper has been integrated with the pump. Two types are available: brushed DC motors and brushless DC motors. Digital customization is also possible with the brushless DC motor.

• Other pumps

Pulsation-reducing liquid pump, a diaphragm liquid pump that significantly reduces pulsation generated during pump suction and discharge.

We have reviewed the design of the pump itself as a liquid pump for pulsation reduction measures. Traditionally, pulsation reduction was achieved using dampers, but we have significantly suppressed pulsation with the pump itself. - FP70 Series We have integrated the pulsation reduction damper with the pump. - FP150 / FP400 / FK1100 Series We have increased the number of diaphragms to a maximum of five, allowing for the cancellation of pulsation within the pump. - FP1.150 / FP1.400 / FK1.1100 Series We have increased the number of diaphragms to a maximum of five, allowing for the cancellation of pulsation within the pump. Additionally, we have improved the maximum allowable discharge pressure to 6 bar (0.6 MPa), achieving smooth liquid transfer even under challenging pressure conditions.

• Other pumps

Pulsation Reduction Gentle Flow Diaphragm Liquid Pump

- The pulsation reduction feature allows for the transfer of liquids with minimal pulsation. - Due to the reduced pulsation, pressure loss in the tubing can be minimized. - It enables the transfer of liquids with fewer air bubbles. - It can reduce the optional parts for pulsation reduction measures. - Equipped with a newly developed valve, it can achieve self-priming suction even at lower motor speeds. - Flow rate adjustment is possible through brushless motor control. - Materials with NFS certification are also available. Basic flow rate: 700 ml/min Diaphragm material: EPDM / PTFE

• Other pumps

Introduction to the mechanism of the low-pulse liquid pump FP400 series. You can see the five-diaphragm system and the movement of the valves.

Introduction to the FP400 series mechanism *The FP150 series has the same mechanism.

• Other pumps

Maintenance procedure video for low pulsation liquid pumps FP150 and FP400 series.

Maintenance can be performed by the users themselves using general-purpose tools.

• Other pumps

High-output type, pulsation control design diaphragm liquid pump, ideal for inkjet printers, high-pressure cleaning systems, etc., with corrosion-resistant components also available.

- High discharge design, maximum allowable discharge pressure 0.6 MPa - Reduced pulsation in liquid delivery - Long lifespan design - Excellent linearity - Self-sustaining - Transfer of sensitive liquids - Abundant wetted materials Significantly reduces pulsation using five diaphragms, controls flow rate with an external signal to a brushless DC motor, and demonstrates a linear flow curve based on the control signal. It offers extensive customization for users' technical challenges and various optional parts are available.

• Other pumps

A damper that reduces pulsation during liquid transfer.

- Reduces pulsation by up to 97% - Accessories specifically for KNF liquid pumps - A wide range of wetted materials available according to liquid composition, just like the pumps - Maintenance-free - NSF certified materials (optional) FPD06: Flow rate up to 1200 ml/min, maximum allowable discharge pressure 0.2 MPa FPD10: Flow rate from 1300 ml/min, maximum allowable discharge pressure 0.2 MPa FPD1.06: Flow rate up to 1200 ml/min, maximum allowable discharge pressure 0.6 MPa FPD1.10: Flow rate from 1300 ml/min, maximum allowable discharge pressure 0.6 MPa

• Other pumps

Pulsation control design diaphragm liquid pump

- Reduced pulsation in liquid delivery - Long lifespan design - Excellent linearity - Self-sustaining - Transfer of sensitive liquids - Abundant wetted materials Basic flow rate: 1.5 l/min (KP) / 1.3 l/min (KT) Suction lift: 2.7 mH2O (KP) / 2.5 mH2O (KT) Discharge lift: 20 mH2O

• Other pumps

In civil engineering sites such as mountainous areas and construction sites, it may be necessary to use wooden boards on slopes or inclined access roads. Hyper CLT boards are civil engineering materials utilizing wood CLT, which can be laid not only on flat ground but also on sloped terrain. They can be used for temporary roads, access routes, heavy machinery entry paths, and measures against muddy conditions, creating a driving environment that takes advantage of the unique surface characteristics of wood. The 5×10 board weighs approximately 230 kg, and the 5×20 board weighs about 460 kg, making them lightweight and easy to install and remove even with small machinery, which is a notable feature for maneuverability in narrow sites. This wooden board is registered as a technology under the Ministry of Land, Infrastructure, Transport and Tourism's NETIS system as "TH-250021-A," and can also be utilized for safety measures and innovative ideas in public works.

Metal cracks are one of the concerns in equipment maintenance operations. Repairs using conventional welding methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" or "secondary damage." Hinode Waterworks Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be performed even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

● To determine the sealing and waterproofing of sealed products based on pressure changes, it is not necessary to conduct tests that involve spraying water on the product or immersing it in water. ● Once the product is placed in a dedicated fixture within the inspection device, waterproofing can be quantitatively confirmed through automatic measurement. ● The target product size is W 300 × D 210 × H 100 mm or smaller. ● The target products include automotive cameras, smartphones, ECUs, small motors, and other packaging containers, and are effective for any products that require confirmation of sealing, waterproofing, and airtightness. ● For product specifications and details, please contact us.

The inspection targets of the "MSX-7003 series" are relatively large electronic devices. 【Inspection Targets】 - LED - Optical devices - High-frequency devices - Power semiconductors - IR sensors - Gyro sensors - Angular velocity sensors - Electrolytic capacitors, etc. The transport system is designed based on "pallet to pallet" to accommodate various types of work. The following three processes are performed automatically by the airtight inspection device: - Helium bombarding - Gross leak test - Fine leak test For packaged products smaller than 10 mm on each side, the work is set up using pallets or trays, followed by helium bombarding ↓ Then transported to the leak test process through high-speed handling ↓ Going through a continuous process from the gross leak test to the fine leak test ↓ And finally, discharged onto a pallet through high-speed handling. It also supports inline operations (the height of the pass line is 940 mm). Please watch the YouTube video from the link below.