[Free Materials Available] Introducing Useful Information on Vehicle Detection Sensors!

Contributing to smooth and efficient parking management, from coin parking to large-scale parking lots.

To guide customers to parking spaces without stress. Hotron's "vehicle detection sensors" adapt to on-site needs, including occupancy management in parking lots, truck berth vehicle detection, merging warnings, exit alerts, and drive-thru applications, allowing for the construction of various systems according to scale. ■ Introduction video of Hotron's vehicle detection sensors https://youtu.be/wij31XlZz00?si=RhhhLeBNYrJPonBD ◎ For detailed information and products, please download the catalog or feel free to contact us.

• Sensors
• Indicator Light
• Signal lights and rotating lights

Achieving cost reduction through occupancy management of parking lots tailored to specific situations, such as floor management, block management, and vehicle room management.

Parking space management refers to the real-time display of parking availability and the management of efficient use of parking spaces. By utilizing Hotron's sensors, drivers can quickly discover available parking spaces, enabling efficient parking lot operations. In large parking lots, there are "floor management methods/block management methods" that prioritize cost reduction and "parking space management methods" that prioritize high accuracy. The floor management/block management methods involve installing sensors at specific points to count and manage the number of passing vehicles. These methods are easy to install and cost-effective. The parking space management method involves installing sensors in every parking space to manage each vehicle individually, achieving high-precision parking management. ■ Target Products - Vehicle Count Sensor CCS2 (Ceiling-mounted, Infrared method) - Occupancy Detection Sensor HM-UX2/UW2 (Ceiling-mounted, Ultrasonic method) ■ Introduction video for the Occupancy Detection Sensor HM-UX2 https://youtu.be/5tzrBAykAqU?si=EwSLqE9WYoolaNCy

• Sensors
• Indicator Light
• Signal lights and rotating lights

In a narrow parking lot, the occupancy status of each parking space is detected to reduce unnecessary entry of new vehicles and ensure safe parking lot operations.

For managing occupancy in small parking lots, the "space management method," which involves installing sensors for each parking space to display availability with higher accuracy, is recommended. In small parking lots, maneuvering vehicles can be difficult, and if a driver mistakenly enters, they may have to back out, leading to customer stress and potential accidents. Therefore, by installing sensors for each parking space to ensure accurate occupancy displays, unnecessary entries of new vehicles can be reduced, enabling safe parking lot operations. ■ Target Products - Vehicle Detection Sensor HM-UX2/UW2 (Ceiling-mounted, Ultrasonic type) - Vehicle/Pass Detection Sensor HM-LC6 (Relay type, Loop coil type) - Vehicle Detection Sensor HM-LC7/LC7-FLS (Communication type, Loop coil type) - Vehicle/Pass Detection Sensor HM-S6 (Buried type, Magnetic type) - Vehicle Detection Sensor HM-S8 (Exposed type, Magnetic type) ■ Introduction Video for Vehicle Detection Sensor HM-UX2 https://youtu.be/5tzrBAykAqU?si=EwSLqE9WYoolaNCy

• Sensors
• Indicator Light
• Signal lights and rotating lights

Install vehicle detection sensors suitable for the scale and method of coin parking, providing real-time occupancy information.

We install vehicle detection sensors suitable for the scale and method of coin parking, such as gate-type/flap-type (lock-type), gate-less/flap-less (lock-less), and provide real-time occupancy information. This ensures accurate occupancy display for safe coin parking operations.

• Sensors
• Indicator Light
• Signal lights and rotating lights

Accurately detects traffic jams and oncoming vehicles! A vehicle counting sensor that can be used for parking space management and as an exit warning.

The "CCS2" is a ceiling-mounted vehicle counting sensor that employs an infrared reflection method. It can be installed at fixed locations such as entrances and ramps, detecting vehicles in both directions with a single unit. It accurately detects and counts vehicles even during traffic jams or when vehicles are passing each other. It contributes to cost reduction in managing occupancy in large parking lots. In addition to vehicle counting, it can also be used as a sensor for exit warnings. 【Features】 ■ Can be installed in high-ceiling environments with a mounting height of 4m ■ Detection area covers 40 spots, allowing for wide-range detection ■ Angle adjustment is possible up to ±5° ■ The display LED is color-coded by direction, making operation confirmation easy ■ Easy installation. Simply set the mounting height and road surface type for straightforward use *For more details, please download the catalog or contact us.

• Safety Sensors
• Other safety equipment

The SSR-3 is ideal for sites where there is a risk of contact with pedestrians! It is a vehicle detection sensor that ensures safety at the exits of parking lots in condominiums and office buildings.

This is a suitable passage detection sensor for locations where there is a risk of pedestrian contact, such as parking lot exits of condominiums and office buildings. The "SSR-3" is a radar-reflection combination sensor that can determine direction with a single unit. It is also compatible with ceiling mounting. Additionally, it can warn of vehicles exiting the parking space when used in conjunction with our rotating light controller. For more details, please contact us or download the catalog.

• Sensors
• Indicator Light
• Signal lights and rotating lights

Industrial sensor for installation at heights of 3.5m to 6.5m. IP65.

"KABUTO" is an industrial sensor designed for installation at heights ranging from 3.5m to 6.5m. It features a long-range radar and a wide infrared area combined sensor. It detects only the desired direction through its directional detection function. 【Features】 ■ IP65 industrial sensor ■ Detects the entry and presence of packer trucks at waste disposal sites ■ Monitors trouble spots at merging locations from a high vantage point ■ Alerts to potential contact accidents involving forklifts within factories ■ Capable of monitoring from a height of 6.5m, with settings adjustable via remote control ■ Ensures stationary detection in a wide infrared area; directional management is possible when used across all areas ■ Manages lateral directionality with cross-traffic functionality ■ Easy installation and initial setup ◎ For more details, please contact us or download the catalog.

• Sensors

Ceiling-mounted ultrasonic sensor for vehicle detection to reliably detect the entry and exit of each parking space.

The "HM-UX2-HM-UW2" is a vehicle detection sensor for parking systems that utilizes ultrasonic technology. It offers excellent cost performance for large-scale parking management. Since it can be configured directly on the sensor itself, a controller is not required. Together with our rotating light controller, it can provide warnings for vehicles exiting the parking space. ★ Introduction video for HM-UX2 can be found here: https://youtu.be/5tzrBAykAqU 【Features】 ● Ceiling-mounted sensor that detects vehicles in each parking space Detection distance can be adjusted according to the ceiling height of the parking lot. ● Detection is possible without being affected by the floor surface! By changing the detection distance as needed, it is unaffected by the floor surface. ● Easy installation with minimal wiring No synchronization lines are needed when installing sensors for each parking space, reducing construction effort. ● Option to select between vehicle detection and passage detection types With dip switch settings, it can be used as either a vehicle detection type or a passage detection type. ● Choose between relay type (UX2) and communication type (UW2) Relay type is recommended for small parking lots, while the communication type with minimal wiring is suitable for larger parking lots. ● Convenient for truck bays and drive-thrus.

• Signal lights and rotating lights

Less affected by the natural environment! A round-shaped vehicle detection sensor evolved with a load capacity 10 times greater (compared to our company).

The "HM-S6" is an embedded park sensor that detects vehicles through changes in magnetic flux, accommodating various situations from passing to stationary vehicles. It is recommended for use with the opening and closing of waste disposal plant doors, as well as for gates where vehicles pass and outdoor parking applications. It can also be installed on reinforced concrete or steel plates. 【Features】 ■ Less susceptible to the effects of natural environments such as rain, snow, temperature changes, and geomagnetism ■ Protection rating IP68 to reduce water ingress ■ Ten times the load capacity compared to conventional embedded park sensors (based on our comparison) ■ Can distinguish between vehicles even when they pass continuously ■ Can be installed on reinforced concrete or steel plates *For more details, please refer to the PDF materials or feel free to contact us.

• Sensors
• Safety Sensors

Communication-type loop coil vehicle detection sensor capable of setting up to 100 vehicle spaces.

The "HM-LC7/LC7-FLS" is a vehicle detection sensor using a communication-type loop coil system. The loop coil sensor is a simple vehicle detection system formed by a coil and a controller. It detects general vehicles in parking lots and traffic management systems. Since each detector is connected via communication lines, it places less burden on installation compared to relay types. It can be configured for up to 100 parking spaces. 【Features】 ■ Loop coil type detector aimed at general vehicles ■ Vehicle detection results are reported to the payment machine via communication (RS-485) ■ Configurable for up to 100 parking spaces ■ Each detector is connected via communication lines, reducing installation burden compared to relay types ■ Flap plate can be raised or lowered based on communication instructions from the payment machine (only for HM-LC7) ■ HM-LC7-FLS is for flapless (no locking plate) use ◎ For more details, please contact us or download the catalog.

• Sensors

Compact-sized loop coil vehicle detection sensor

The "HM-LC6" is a relay-type loop coil vehicle presence and passage detection sensor. The loop coil sensor is a simple vehicle detection system formed from a coil and a controller. It detects general vehicles in parking lots and traffic management systems. Additionally, it can issue warnings for vehicles exiting from parking spaces when used in conjunction with our rotating light controller. 【Features】 ■ Loop coil type detector targeting general vehicles ■ Achieves high-accuracy occupancy management in small parking lots ■ Recommended for the opening and closing of input doors at waste disposal sites and outdoor parking lots ■ Adopts an automatic tuning method, adjusting to the optimal operating point of the device simply by powering it on ■ Can be used as a sensor for exit warnings when combined with an exit warning light For more details on the exit warning system, click here↓ http://www.hotron.co.jp/recommend/car_alert.html ◎ For more information, please contact us or download the catalog.

• Sensors
• Safety Sensors
• Signal lights and rotating lights

Vehicle detection sensor that does not detect people or animals, unaffected by natural environments such as rain and snow or geomagnetic influences.

The "HM-S8" is an exposed type park sensor that does not require installation and is less affected by natural environments such as rain and snow, as well as geomagnetic influences. It is installed next to the flap plate, eliminating the need for burial during construction. The vehicle detection results are reported to the payment machine via communication (RS-485). 【Features】 ■ Less affected by natural environmental factors such as rain, snow, temperature changes, and geomagnetism ■ Protection rating IPX7 ■ Does not detect humans or animals ■ Installed next to the flap plate (no burial required) ■ Usable without a flap (passage is not allowed) ■ Cables available in 1.5M and 2M lengths ■ Achieves high-accuracy occupancy management in small parking lots *For more details, please refer to the PDF document or feel free to contact us.

• Sensors
• Safety Sensors

Fukuda Co., Ltd., which develops, manufactures, and sells leak testing equipment to inspect airtightness and sealing performance, provides a technical document that clearly explains the methods and theories of airtight testing, titled "Technical Manual." We are offering it as a PDF file. Please take this opportunity to download and view it!

● What is a packaging container air leak test device? It is a leak testing device that identifies the peeling, tearing, and presence of pinholes in packaging containers for pharmaceuticals and other products, conducting a Container Closure Integrity Test (CCIT). It can be applied to a wide variety of packaging containers, including flexible packaging, bottle containers, and glass containers, primarily in pharmaceutical packaging. The measurement method employs the <sealed chamber method (pressure change leak testing method 1)>. A sample is placed in the chamber, and by applying pressure or vacuum and measuring the pressure change within the chamber, quantitative inspection is performed. It can be used in various scenarios, including offline manufacturing, inline manufacturing, CMC laboratories, quality control laboratories, and stability testing. * The containers subject to inspection are referred to as "work" or "samples." Here, specific samples are referred to as "samples" to differentiate the terminology.

The pinhole inspection for packaging engineering is fully automated, eliminating packaging defects based on certain quality standards. The judgment results and operational status can be managed via a monitor screen. - Quantitative management of quality standards for the pinhole inspection process - Ensuring the quality of the product's shelf life - Establishing evaluation criteria for the manufacturing process, achieving quantitative quality assurance - Slim and space-saving design that can be connected to existing production lines - Quick changeover for product variety switching can be handled in a short time by exchanging chambers - Fully domestically produced, allowing for rapid maintenance and troubleshooting - Example target works: pillow packaging, packaged rice (packaged cooked rice), etc. *Please consult us regarding the use of this product for pharmaceuticals.

In construction work, it is important not only to focus on the building itself but also to create a safe environment for construction vehicles and workers to move around. The Hyper CLT plywood is a lightweight wooden board that utilizes CLT. It can be used as temporary materials to support temporary roads, material delivery routes, heavy machinery work yards, material storage areas, and worker pathways, rather than as structural materials for buildings. The 5×10 board weighs approximately 230 kg, making it relatively lightweight and easy to install, remove, or relocate depending on site conditions. This allows for the boards to be moved in accordance with the progress of the construction, making it easier to effectively utilize limited space. Additionally, the natural texture of the wood blends well with construction sites in residential areas and around public facilities, contributing to considerations for metal noise and summer heat reflection. The Hyper CLT plywood is a registered technology under the Ministry of Land, Infrastructure, Transport and Tourism's NETIS system, designated as "TH-250021-A." It can be incorporated into highly public construction projects and exterior and earthworks, promoting the use of new technologies and environmental considerations. Wooden plywood, NETIS, civil engineering, CLT, lightweight wooden boards. A new option for temporary materials using wood is available for construction sites.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or variations in dimensions, can be molded at the same time in a single molding process. This allows for the verification of multiple types in a short period.