[Webinar] "Introduction to TOC and VFA Measurement in Wastewater, and Hydrogen Sulfide Sensors - Laboratory and Online Analytical Devices" July 10, 2026 (Friday) 11:00 - 11:45

Simultaneous automatic measurement of TN and TP along with TOC! An online TOC analyzer that contributes to the optimization of wastewater processes.

●BioTector B7000 can measure TOC simultaneously with TN/TP. The simultaneous measurement cycle for TOC/TN/TP takes around 10 minutes, and it automatically cleans the sample tube while operating, eliminating downtime for cleaning clogged drainage. The short measurement cycle for TN/TP is well-received: some customers use it to measure only TN/TP or either one without measuring TOC. ●Measurement Time ◎TOC: <7 minutes ◎TN: TOC <7 minutes, TN <2 minutes ◎TP: TOC <10 minutes, TN/TP <8 minutes ●Measurement Range ◎TOC: Minimum 0-50 mg/L, Maximum 0-20,000 mg/L ◎TN: (Cell length 2mm) Minimum 0-19 mg/L, Maximum 0-5,000 mg/L, (Cell length 0.5mm) Minimum 2-55 mg/L, Maximum 160-15,000 mg/L ◎TP: (Cell length 10mm) Minimum 0-11 mg/L, Maximum 0-3,000 mg/L, (Cell length 5mm) Minimum 1-18 mg/L, Maximum 60-5,000 mg/L Please also check out the video summarizing "no clogging" in 50 seconds.

• Water quality testing

TOC analyzer with internal automatic cleaning function that reduces clogging and maintenance hassle! Demo units available for loan.

The online TOC analyzer BioTector offers several models tailored to your usage needs. The 'B7000i' is an online TOC analyzer designed for high-concentration wastewater, equipped with an internal automatic cleaning function that minimizes clogging and maintenance hassles. It can measure wastewater containing soft particles up to 2mm in diameter without dilution, allowing for automatic measurements without downtime, without the need for cleaning clogs or stopping the device. Depending on the application, various models can be selected for COD/BOD/TC, with one unit capable of handling up to 6 channels. Explosion-proof models (overseas explosion-proof) are also available. It employs a unique wet two-stage oxidation method. If there are challenges with oxidation power in the wet method, this approach overcomes those issues. 【Features】 ■ Internal automatic cleaning function ■ Reduces clogging and maintenance hassles ■ Annual operating rate of over 99% ■ Various model selections available based on application *For more details, please refer to the catalog. Feel free to contact us with any inquiries.

• Other measurement, recording and measuring instruments

"Online TOC meter" is widely usable for measuring inflow water, process water, reclaimed water, and wastewater.

The Hack Ultra online TOC analyzer BioTector B3500 series has achieved miniaturization and cost reduction by specializing in low-concentration samples, utilizing the same wet two-stage oxidation method as the higher-end B7000 model. It can be widely used for measuring inflow water, process water, reclaimed water, and wastewater. ■ The online TOC analyzer B3500 is available in three models to suit various applications: - B3500ul A TOC analyzer for low-concentration samples such as cooling water and RO water. It can be used without dilution and without blockage for soft particles up to 100 μm. - B3500c A TOC analyzer for standard samples such as reclaimed water and effluent. It can be used without dilution and without blockage for soft particles up to 100 μm. It can be configured with up to two flow paths as an option. - B3500e A TOC analyzer for high-concentration samples such as industrial wastewater. It features a self-cleaning function, resolving issues related to clogging of the sample tube. It can be used without dilution and without blockage for soft particles up to 100 μm.

• Other measurement, recording and measuring instruments

Supports particles up to 0.8mm - Laboratory TOC/TN Analyzer QP1680

The QP1680 is a laboratory TOC/TNb analyzer. Due to its combustion oxidation method, it can handle relatively high-concentration samples that contain fine particles and salts. In addition to the type that performs combined analysis of total organic carbon (TOC) and total bound nitrogen (TNb), there are also types that measure only TOC or only TNb, allowing you to choose according to your needs. Accurate measurement of TOC and TNb is essential for optimizing industrial processes, improving product quality, and protecting the environment. The QP1680 provides efficient monitoring and reliable measurement results.

• Water quality testing

Real-time VFA monitoring device to maximize the efficiency of methane fermentation in anaerobic digestion.

The online VFA meter EZ7200 series is a high-performance online titration device designed for monitoring wet anaerobic digestion tanks. It proposes a new management method for medium to large-scale anaerobic digestion processes. In biomass power generation, industrial wastewater, and sewage treatment, the anaerobic treatment of wastewater and sludge in fermentation tanks involves the breakdown of very complex organic carbon compounds, which presents challenges. Real-time measurement of VFA (volatile fatty acids) is effective for stabilizing the methane fermentation tank in anaerobic treatment. Relying solely on pH measurement and sampling can make it difficult to monitor the conditions inside the fermentation tank, depending on the timing. The ideal pH value inside the fermentation tank is said to be between 6.5 and 7.5, but measuring pH alone is not sufficient; adequate buffering capacity [total alkalinity TAC (also referred to simply as alkalinity)] is necessary to compensate for changes in acid concentration. By continuously monitoring VFA, which are intermediate substances during methane fermentation, it contributes to maintaining a more stable fermentation tank and maximizing gas production. By conducting online measurements at 10-15 minute intervals, it becomes possible to anticipate various events within the digestion tank in advance.

• Water quality testing

We would like to express our congratulations on the continued prosperity of your esteemed company. Our company will be exhibiting at the following trade show, where we will be showcasing a number of products, including our new product, the Packaging Container Air Leak Test (Pin Hole Inspection) Device | MSQ-2003 series. We sincerely apologize for the inconvenience during your busy schedule, but we would like to cordially invite you to attend this event. 【 Trade Show Name 】 【 Dates 】 【 Venue/Booth Number 】

We will be exhibiting at Smart Factory JAPAN, held at Tokyo Big Sight from November 18 (Wednesday) to November 20 (Friday), 2026. We will introduce the 'Dr. Process Navi Series', 'Dr. Mold Cloud', and AI solutions that integrate with both products! <Introducing the latest solutions that innovate productivity in manufacturing sites!> ● 'Dr. Process Navi' Series ● 'Dr. Mold Cloud' ● 'AI Solutions' For more details, please check the related products. ■■ Smart Factory JAPAN 2026 Overview ■■ Dates: November 18 (Wednesday), 19 (Thursday), 20 (Friday), 2026 Opening Hours: 10:00 AM - 5:00 PM Venue: Tokyo Big Sight, East Hall 1-3 Our Booth Number: F-20 Registration: Nikkan Kogyo Shimbun 6 Exhibition Joint Site When visiting, please register in advance from your My Page and bring a printed admission ticket. Business meeting requests are also possible, so please make use of this opportunity.

We will be exhibiting at the Monozukuri World Fukuoka Design and Manufacturing Solutions Exhibition, held at Marine Messe Fukuoka from December 2 (Wednesday) to December 4 (Friday), 2026. We will introduce the 'Dr. Process Navi Series', 'Dr. Mold Cloud', and AI solutions that help improve efficiency and reform in manufacturing sites! <Introducing the latest solutions that innovate productivity in manufacturing sites!> ● 'Dr. Process Navi' Series ● 'Dr. Mold Cloud' ● 'AI Solutions' For more details, please check the related products. ■■ Overview of the 4th Monozukuri World Fukuoka Design and Manufacturing Solutions Exhibition ■■ Dates: December 4 (Wednesday), 5 (Thursday), 6 (Friday), 2026 Opening hours: 10:00 AM to 5:00 PM Venue: Marine Messe Fukuoka Our booth number: 14-18 When visiting, please register in advance through the dedicated page and bring your printed visitor badge.

We will showcase our new product "BLFF," a palletizing foam gripper that weighs only 1.9 kg and measures 350mm×250mm, ideal for bulk picking. We will also introduce various products that cater to different work applications, including durable suction cups and solutions for bag handling. Additionally, we are implementing energy-saving proposals by replacing ejectors to reduce compressed air consumption, which has become a challenge in many industries. If you have any issues with adhesion or transport, please feel free to consult with us at the venue. ■ Lightweight Foam Gripper for Collaborative Robots "CVGC Series" Despite weighing only 1.9 kg, this gripper has a theoretical lifting force of 100 kg, maximizing the payload capacity of collaborative robots. ■ Gripper for Films This gripper is designed to transport thin films gently, minimizing marks left on the surface. By utilizing 3D printing, we can accommodate highly flexible shape designs tailored to specific workpieces and applications. ■ Energy Saving Comparison Panel "Why does a single ejector consume less compressed air compared to a multi-stage ejector?" You can actually verify the differences in compressed air consumption through a comparative display using a flow meter and actual equipment.

We will be exhibiting at "CEATEC 2026," which will be held at Makuhari Messe from October 13 to 16. We provide information technology and process informatics (PI) that optimize "how to create" by utilizing physical simulations, AI, and machine learning in process development. We look forward to your visit to our booth. 【Seminar Information】 "Process Informatics for Exploring Optimal Manufacturing Conditions" Date and Time: October 16, 2026 (Friday) 12:45 - 13:00 Venue: Makuhari Messe Exhibition Hall 4 P Stage Speaker: CEO Takaishi Please check the link below for details on our exhibition.