We will be exhibiting at "Interfex Week Osaka 2020."

A stirring device that can vigorously mix liquids in a one-dan can or a pail can without transferring them.

This is a Bernoulli flow stirring device that powerfully stirs liquids without transferring them from a 20-liter can or a pail. It can be attached to a hand mixer or a drill. - It can be directly inserted into containers such as 20-liter cans, pails, bag-in-boxes, and poly tanks, as long as the opening is 32mm or larger. - Since it does not require cutting the top of the can, the risk of foreign matter contamination is reduced, and the cap can be replaced for storage after stirring. - There is no need for physically demanding tasks such as transferring to another container or shaking the can, which reduces the burden on the operator. - The stirring body adopts the L-shaped Bernoulli flow stirring body BEAG, which minimizes air entrapment and foaming. - It powerfully stirs liquids from low to high viscosity using centrifugal force generated by high-speed rotation. - The stirring body, which is integrated with the stirring shaft, is not only resistant to damage but also has no gaps for dirt to enter, making it easy to clean. - It can be attached to hand mixers or drills with a shaft diameter of φ10mm or φ12mm. - By adjusting the rotation speed, efficient stirring can be achieved.

• Mixer/agitator

High power for reduced heating time! Stainless container with a heater that can warm up in a short time.

1. Compact Equipment The heater unit is directly attached to the container, making the equipment compact and space-efficient. Since all the devices are mounted on the container, moving it is easy. 2. No Initial Cost Chillers with both heating and cooling functions are expensive and have a higher initial cost compared to heaters. If only heating of the jacket is needed, heaters are overwhelmingly more cost-effective in terms of initial investment. 3. Can Quickly Heat the Jacket By adopting a 7.5kW heater, the water in the jacket can be heated to high temperatures in a short time, warming the contents. Product Features - The heater is installed in the jacket section, allowing for liquid heating with just this unit. - It has a dry-run prevention feature, so the heater stops when the water in the jacket is low. - Equipped with a level gauge to check the water level in the jacket. - The temperature of the mixed liquid can be adjusted through the linkage between the thermometer and the heater. - A stirrer can be attached to the container, allowing for uniform heating of the contents. As this is a made-to-order product, modifications to "dimensions" and "materials" can be made, as well as custom processing to suit specific applications.

• tank

This is an original air motor mixer from Nitto Metal Industry. It is ideal for preventing foaming during mixing and for stirring high-viscosity liquids.

- It can stir in a sealed state with a Heller connection. Pressure reduction is also possible. - It can stir liquids with low to medium-high viscosity. - It comes standard with a waste receiver to prevent contamination from wear particles generated at the shaft seal. - The stirring body is a Bernoulli flow stirring body type BEAG E, which is less likely to incorporate air. (Patent No. 6169207) - It can be used in explosion-proof areas. - Made entirely of stainless steel, it is resistant to rust and hygienic. - It can be used without lubrication, so there is no oil splatter. For more details, please visit our website. https://www.monovate.co.jp/shop/g/gntma-s/

• Mixer/agitator

This is an original electric motor stirrer from Nitto Metal Industry. It is ideal for preventing foaming during stirring and for stirring high-viscosity liquids.

- It features an easy-to-remove and attach connection. - It can stir in a sealed state and is usable under both pressurized and vacuum conditions. - It can stir liquids with low to medium-high viscosity. - It comes standard with a debris collector to prevent contamination from wear particles generated at the shaft seal. - The stirring element is a Bernoulli flow stirring element type BEAG E, which is designed to minimize air entrapment. (Patent No. 6169207) - It is equipped with a standard controller that allows for speed adjustment. For more details, please visit our website. https://www.monovate.co.jp/shop/g/gntme-a/

• Other energy equipment

A manufacturer specializing in liquid mixing has produced it! Here is a summary of the features of the mixer equipped with the Bernoulli flow mixing body BEAG.

The Bernoulli flow mixer introduced in this document is a mixer equipped with the Bernoulli flow stirring body BEAG. The Bernoulli flow stirring body BEAG utilizes centrifugal force. By utilizing the pressure difference created by centrifugal force, it stirs liquids uniformly. A characteristic of BEAG is that it does not have stirring blades like propellers or holes for utilizing centrifugal force. The Bernoulli flow mixer is recommended for customers who are facing the following issues: - They are dealing with high-viscosity liquids that are difficult to mix, causing delays in stirring operations. - The liquid is settling, making it hard to stir. - They want to eliminate air entrapment. - They want to use it in a sealed and pressure-resistant manner. - They want to prevent foreign matter contamination from the shaft. This document summarizes the mechanism of BEAG's stirring and the centrifugal mixer equipped with BEAG. Please take a look.

• Mixer/agitator

We would like to express our congratulations on the continued prosperity of your esteemed company. Our company will be exhibiting at the following trade show, where we will be showcasing a number of products, including our new product, the Packaging Container Air Leak Test (Pin Hole Inspection) Device | MSQ-2003 series. We sincerely apologize for the inconvenience during your busy schedule, but we would like to cordially invite you to attend this event. 【 Trade Show Name 】 【 Dates 】 【 Venue/Booth Number 】

We will showcase our new product "BLFF," a palletizing foam gripper that weighs only 1.9 kg and measures 350mm×250mm, ideal for bulk picking. We will also introduce various products that cater to different work applications, including durable suction cups and solutions for bag handling. Additionally, we are implementing energy-saving proposals by replacing ejectors to reduce compressed air consumption, which has become a challenge in many industries. If you have any issues with adhesion or transport, please feel free to consult with us at the venue. ■ Lightweight Foam Gripper for Collaborative Robots "CVGC Series" Despite weighing only 1.9 kg, this gripper has a theoretical lifting force of 100 kg, maximizing the payload capacity of collaborative robots. ■ Gripper for Films This gripper is designed to transport thin films gently, minimizing marks left on the surface. By utilizing 3D printing, we can accommodate highly flexible shape designs tailored to specific workpieces and applications. ■ Energy Saving Comparison Panel "Why does a single ejector consume less compressed air compared to a multi-stage ejector?" You can actually verify the differences in compressed air consumption through a comparative display using a flow meter and actual equipment.

We will be exhibiting at Smart Factory JAPAN, held at Tokyo Big Sight from November 18 (Wednesday) to November 20 (Friday), 2026. We will introduce the 'Dr. Process Navi Series', 'Dr. Mold Cloud', and AI solutions that integrate with both products! <Introducing the latest solutions that innovate productivity in manufacturing sites!> ● 'Dr. Process Navi' Series ● 'Dr. Mold Cloud' ● 'AI Solutions' For more details, please check the related products. ■■ Smart Factory JAPAN 2026 Overview ■■ Dates: November 18 (Wednesday), 19 (Thursday), 20 (Friday), 2026 Opening Hours: 10:00 AM - 5:00 PM Venue: Tokyo Big Sight, East Hall 1-3 Our Booth Number: F-20 Registration: Nikkan Kogyo Shimbun 6 Exhibition Joint Site When visiting, please register in advance from your My Page and bring a printed admission ticket. Business meeting requests are also possible, so please make use of this opportunity.

We will be exhibiting at the Monozukuri World Fukuoka Design and Manufacturing Solutions Exhibition, held at Marine Messe Fukuoka from December 2 (Wednesday) to December 4 (Friday), 2026. We will introduce the 'Dr. Process Navi Series', 'Dr. Mold Cloud', and AI solutions that help improve efficiency and reform in manufacturing sites! <Introducing the latest solutions that innovate productivity in manufacturing sites!> ● 'Dr. Process Navi' Series ● 'Dr. Mold Cloud' ● 'AI Solutions' For more details, please check the related products. ■■ Overview of the 4th Monozukuri World Fukuoka Design and Manufacturing Solutions Exhibition ■■ Dates: December 4 (Wednesday), 5 (Thursday), 6 (Friday), 2026 Opening hours: 10:00 AM to 5:00 PM Venue: Marine Messe Fukuoka Our booth number: 14-18 When visiting, please register in advance through the dedicated page and bring your printed visitor badge.

Announcement of participation in the "12th Robot and Aerospace Festival Fukushima 2026 / 5th Drone Summit." 【Date and Time】 　November 27, 2026 (Wednesday) 10:00 AM - 5:00 PM Business Exhibition 　November 28, 2026 (Thursday) 10:00 AM - 4:00 PM General Exhibition 【Venue】 　Big Palette Fukushima (52 Minami 2-chome, Koriyama City, Fukushima Prefecture) 【Exhibits】 　Cardboard Insulated Box 　Craft Cooler Cube