PICO Corporation High Power Output DC/DC Power Supply

Palm-sized with high power output, maximum output 300W.

PICO's high power output series (QP/LP/P/XP series) is a compact DC/DC power supply with a wide input range, high efficiency, low ripple, isolation, and a wide temperature range.

• Other power sources

The HPHA series is among the world's smallest with a high power of 2000W, making it suitable for the front end of aircraft power supplies.

The HPHA series from PICO is a three-phase AC-DC converter designed for aircraft installation. It can be connected to a DC-DC converter in the subsequent stage to generate multiple voltages.

• Other power sources

PICO's products can support output up to 10,000V.

PICO's high-voltage output series (AV/SMV/VV series) is a DC/DC converter capable of boosting up to 5,000V, all in a compact 0.5-inch package.

• Other power sources

Fukuda Co., Ltd. has been pursuing leak detection for 60 years and is committed to advancing the future of leak testing. 【 Supporting Various Leak Tests: Air Leak Test / Gas Leak Test (Hydrogen Gas, Helium Gas) 】 We develop, manufacture, and sell leak testing equipment to inspect airtightness and sealing properties. We will propose the appropriate testers and devices for each inspection target. 【 Target Industries and Examples of Inspection Targets 】 - Automotive Industry: Engines, FC components, valves and piping, various parts - Electronic Components Industry: Smartphones, keyless switches, various small sensors - Pharmaceuticals / Food / Cosmetics Industry: Bottle containers, syringes, vials, eye drop containers, pillow packaging, PTP packaging We will propose the most suitable leak testers for each industry. 【 ISO Certification 】JIS Q 9001:2015 (ISO 9001:2015)

We will introduce the implementation results of the sensor technology developed by the Hotron Group, which has been cultivated over more than half a century, through customer case studies. In addition to automatic door sensors, we also offer a wide range of vehicle detection sensors and nursing/care sensors. Many implementation examples are also presented, so please take a look at the case study page.

The inspection targets of the "MSX-7003 series" are relatively large electronic devices. 【Inspection Targets】 - LED - Optical devices - High-frequency devices - Power semiconductors - IR sensors - Gyro sensors - Angular velocity sensors - Electrolytic capacitors, etc. The transport system is designed based on "pallet to pallet" to accommodate various types of work. The following three processes are performed automatically by the airtight inspection device: - Helium bombarding - Gross leak test - Fine leak test For packaged products smaller than 10 mm on each side, the work is set up using pallets or trays, followed by helium bombarding ↓ Then transported to the leak test process through high-speed handling ↓ Going through a continuous process from the gross leak test to the fine leak test ↓ And finally, discharged onto a pallet through high-speed handling. It also supports inline operations (the height of the pass line is 940 mm). Please watch the YouTube video from the link below.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can cause changes in the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for the repair of metal cracks without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material with heat. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for casting prototypes can be shortened! Since model production is not required, the time needed to create prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or variations in dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.