Visualizing infrared light from 700 to 1700 nm! IR sensor card / infrared sensor card

Visualization of infrared light from 700 to 1700 nm through electronic trapping!!!

The IR sensor card (infrared sensor card) is laminated and is the most common product in the IR sensor series. It emits visible light from the area where infrared is irradiated. The letter R (reflective) at the end of the model number indicates that the IR beam image is displayed only on the front side of the card (the irradiated side). The letter T (transmissive or translucent) at the end of the model number indicates that the IR beam image is displayed on both sides of the card. At the same infrared intensity, the R type card provides a clearer image due to the backing of reflected light. The phosphor layer is laminated between transparent plastics suitable for various near-infrared detection and imaging applications.

• Other inspection equipment and devices

Visualizing infrared light from 700 to 1700 nm through "electronic trapping"!!!

The IR sensor seal (infrared sensor seal) is a thin, flexible sheet-type sensor. It emits visible light from the area where infrared light is irradiated. It can be cut into any shape and used by peeling off the backing to stick it in various locations. The phosphor is coated with adhesive on transparent Mylar. This sensor seal is not laminated. By attaching the sensor seal to reflective materials, it becomes a reflective sensor, allowing confirmation of light emission from the irradiated surface. When attached to transparent materials, it acts as a transmissive sensor, enabling light emission to be confirmed from both sides.

• Other inspection equipment and devices

Visualizing infrared light from 700 to 1700 nm using "electronic trapping"!!!

The infrared position detection board is a sensor printed with crosshairs and circular sighting lines on a 3mm thick polycarbonate substrate. It emits visible light from the areas where infrared is irradiated, making it ideal for adjusting the optical axis of infrared. There are versions available in reflective (R) and transmissive (T). They can be secured to various fixtures using clamps, drilling, bolting, or other methods for installation on different equipment. Both versions have measurement lines marked in 2mm increments.

• Other inspection equipment and devices

Visualizing ultraviolet light from 250nm to 500nm!!!

The UV sensor card (ultraviolet sensor card) is laminated and is the most common product in the UV sensor series. It emits visible light from the areas exposed to ultraviolet radiation. The letter R (reflective) at the end of the model number indicates that the UV beam image is displayed only on the front side of the card (the irradiated side). The letter T (transmissive or translucent) at the end of the model number indicates that the UV beam image is displayed on both sides of the card. At the same ultraviolet intensity, the R-type card provides a clearer image due to the backing of reflected light. The surface is not laminated to prevent the blocking of ultraviolet rays.

• Other inspection equipment and devices

Visualizing ultraviolet light from 250nm to 500nm!!!

The UV sensor seal (ultraviolet sensor seal) is a thin, flexible sheet-type sensor. It emits visible light from the area exposed to ultraviolet radiation. It can be cut into any shape and used by peeling off the backing to stick it in various locations. The phosphor is coated with adhesive on a transparent Mylar. This sensor seal is not laminated. By adhering the sensor seal to reflective materials, it becomes a reflective-type sensor, allowing you to confirm the emission from the irradiated surface. When attached to transparent materials, it acts as a transmissive-type sensor, enabling confirmation of emission from both sides.

• Other inspection equipment and devices

In civil engineering sites, workers walk around the site throughout the day. Moving over hard steel plates, experiencing strong glare and radiant heat during the summer, and being surrounded by the metallic sounds of vehicles can make the ground environment burdensome. The Hyper CLT board is a wooden lightweight board made from CLT (Cross-Laminated Timber) that is laminated in a perpendicular direction. The unique texture and temperature of the wood surface differ from that of steel plates, providing an opportunity to reconsider the environment of worker pathways, rest areas, and material storage. The 5×10 board weighs approximately 230 kg, and the 5×20 board weighs about 460 kg, making them relatively lightweight and easy to install, remove, or relocate depending on site conditions. The Hyper CLT board is registered as a technology with the Ministry of Land, Infrastructure, Transport and Tourism under NETIS as "TH-250021-A." It can also be utilized for proposals to improve working environments and consider environmental impact. Wooden boards, NETIS, civil engineering, CLT, wooden lightweight boards. Reevaluating the ground environment contributes to creating a more comfortable workplace.

Hertz Electronics Co., Ltd. will update the software for its "Pokayoke Tools," a group of IoT tools that support the prevention of operator errors (Pokayoke) in production processes such as assembly and inspection, which require high quality. The update will add the "Communication Log Storage for Tool-Used Work" feature to the Pokayoke receiver TW-870R series (single output type "TW-870R," four output type "TW-870R-EXP," LAN connection type "TW-870R-EXL"). The "Communication Log Storage for Tool-Used Work" feature allows for the logging of work performed with Pokayoke-compatible tools (tools equipped with Pokayoke transmitters) each time work is done, storing logs of the work performed (transmitter serial number, work achievements, etc.) and logs of the wireless communication between the Pokayoke transmitter and the TW-870R series (communication date and time, channel, number of transmissions, etc.) as communication logs within the TW-870R series. The communication logs stored in the TW-870R series can be output in CSV format via the Windows application "Pokayoke Tools Settings," allowing for analysis of the wireless communication status in the production process and management of work history using Pokayoke-compatible tools.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding repair methods can alter the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" or "secondary damage." Hinode Water Supply Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repair without the application of heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.

● The production time for cast prototypes can be shortened! Since model making is not required, the production time for prototypes, which previously took about a month, can be significantly reduced. ● Model costs can be reduced! By directly producing sand molds from 3D data, there is no need for model production costs. If changes to the model are necessary, they can be addressed by modifying the 3D data. ● Similar products with different shapes and dimensions can be prototyped simultaneously! Different products, such as similar shapes or varying dimensions, can be molded at the same time in one molding process. This allows for the verification of multiple types in a short period.

Metal cracks are one of the concerns in equipment maintenance operations. Conventional welding methods for repairs can change the base material around the crack due to heat, leading to residual stress and deformation, which always carries the risk of "crack recurrence" and "secondary damage." Hinode Waterworks Equipment Co., Ltd.'s "Mechanical Stitching Method" is a new technique that allows for metal crack repairs without applying heat. By using special bolts and reinforcement plates, the crack is physically removed without affecting the base material at all. Repairs can be made even in environments where open flames cannot be used. Since no heat is applied, the disassembly of equipment is minimized. For more details, please contact us or download the catalog.