Visualize infrared light from 700 to 1700nm! IR sensor seal / infrared sensor seal [Can be cut into any shape]

Visualizing infrared light from 700 to 1700 nm through "electronic trapping"!!!

The IR sensor seal (infrared sensor seal) is a thin, flexible sheet-type sensor. It emits visible light from the area where infrared light is irradiated. It can be cut into any shape and used by peeling off the backing to stick it in various locations. The phosphor is coated with adhesive on transparent Mylar. This sensor seal is not laminated. By attaching the sensor seal to reflective materials, it becomes a reflective sensor, allowing confirmation of light emission from the irradiated surface. When attached to transparent materials, it acts as a transmissive sensor, enabling light emission to be confirmed from both sides.

• Other inspection equipment and devices

Visualization of infrared light from 700 to 1700 nm through electronic trapping!!!

The IR sensor card (infrared sensor card) is laminated and is the most common product in the IR sensor series. It emits visible light from the area where infrared is irradiated. The letter R (reflective) at the end of the model number indicates that the IR beam image is displayed only on the front side of the card (the irradiated side). The letter T (transmissive or translucent) at the end of the model number indicates that the IR beam image is displayed on both sides of the card. At the same infrared intensity, the R type card provides a clearer image due to the backing of reflected light. The phosphor layer is laminated between transparent plastics suitable for various near-infrared detection and imaging applications.

• Other inspection equipment and devices

Visualizing infrared light from 700 to 1700 nm using "electronic trapping"!!!

The infrared position detection board is a sensor printed with crosshairs and circular sighting lines on a 3mm thick polycarbonate substrate. It emits visible light from the areas where infrared is irradiated, making it ideal for adjusting the optical axis of infrared. There are versions available in reflective (R) and transmissive (T). They can be secured to various fixtures using clamps, drilling, bolting, or other methods for installation on different equipment. Both versions have measurement lines marked in 2mm increments.

• Other inspection equipment and devices

Visualizing ultraviolet light from 250nm to 500nm!!!

The UV sensor card (ultraviolet sensor card) is laminated and is the most common product in the UV sensor series. It emits visible light from the areas exposed to ultraviolet radiation. The letter R (reflective) at the end of the model number indicates that the UV beam image is displayed only on the front side of the card (the irradiated side). The letter T (transmissive or translucent) at the end of the model number indicates that the UV beam image is displayed on both sides of the card. At the same ultraviolet intensity, the R-type card provides a clearer image due to the backing of reflected light. The surface is not laminated to prevent the blocking of ultraviolet rays.

• Other inspection equipment and devices

Visualizing ultraviolet light from 250nm to 500nm!!!

The UV sensor seal (ultraviolet sensor seal) is a thin, flexible sheet-type sensor. It emits visible light from the area exposed to ultraviolet radiation. It can be cut into any shape and used by peeling off the backing to stick it in various locations. The phosphor is coated with adhesive on a transparent Mylar. This sensor seal is not laminated. By adhering the sensor seal to reflective materials, it becomes a reflective-type sensor, allowing you to confirm the emission from the irradiated surface. When attached to transparent materials, it acts as a transmissive-type sensor, enabling confirmation of emission from both sides.

• Other inspection equipment and devices

In civil engineering sites, the use of sheet piling methods is essential for safely utilizing the site, including temporary roads, access roads, heavy machinery work yards, material storage areas, and worker pathways. Traditionally, steel plates have been widely used, but due to their weight, they can be cumbersome to transport, install, and remove. Hyper CLT sheet piles are civil engineering materials made from wooden CLT for civil use. The 5×10 panel weighs approximately 230 kg, and the 5×20 panel weighs about 460 kg, making them lightweight and easy to handle with small machinery, contributing to reduced burdens during installation and improved work efficiency. They can be utilized in a wide range of civil engineering sites for measures against muddy conditions, ground protection, heavy machinery scaffolding, and ensuring pedestrian pathways. As a registered technology under the Ministry of Land, Infrastructure, Transport and Tourism NETIS "TH-250021-A," it is also recommended as a material for innovative ideas, safety measures, and environmental considerations in public works.

Fukuda Co., Ltd. has been pursuing leak detection for 60 years and is committed to advancing the future of leak testing. 【 Supporting Various Leak Tests: Air Leak Test / Gas Leak Test (Hydrogen Gas, Helium Gas) 】 We develop, manufacture, and sell leak testing equipment to inspect airtightness and sealing properties. We will propose the appropriate testers and devices for each inspection target. 【 Target Industries and Examples of Inspection Targets 】 - Automotive Industry: Engines, FC components, valves and piping, various parts - Electronic Components Industry: Smartphones, keyless switches, various small sensors - Pharmaceuticals / Food / Cosmetics Industry: Bottle containers, syringes, vials, eye drop containers, pillow packaging, PTP packaging We will propose the most suitable leak testers for each industry. 【 ISO Certification 】JIS Q 9001:2015 (ISO 9001:2015)

In civil engineering sites, there are many instances where temporary roads, access routes, heavy machinery workspaces, and material storage areas use ground plates. Traditional steel plates are heavy, requiring large machinery for installation and removal, which can make work difficult in narrow sites. Hyper CLT ground plates are lightweight civil engineering CLT materials made from wooden CLT for civil use. A 5×10 plate weighs about 230 kg, and a 5×20 plate weighs about 460 kg, making them easy to handle even with small machinery, thus reducing the burden of transportation, installation, and removal. They are easy to use in sites with limited space or where the use of large machinery is difficult. They can be widely used for temporary roads, heavy machinery scaffolding, pathways within the site, and material storage protection, contributing to glare reduction, noise reduction, and environmental consideration. As a registered technology with the Ministry of Land, Infrastructure, Transport and Tourism under NETIS "TH-250021-A," they are also recommended as materials for innovative ideas and safety measures in public works.

We will introduce the implementation results of the sensor technology developed by the Hotron Group, which has been cultivated over more than half a century, through customer case studies. In addition to automatic door sensors, we also offer a wide range of vehicle detection sensors and nursing/care sensors. Many implementation examples are also presented, so please take a look at the case study page.

Fukuda Co., Ltd., which develops, manufactures, and sells leak testing equipment to inspect airtightness and sealing performance, provides a technical document that clearly explains the methods and theories of airtight testing, titled "Technical Manual." We are offering it as a PDF file. Please take this opportunity to download and view it!