List of Contract measurement products

Achieves high collection efficiency through electrostatic methods. Offers a wide range of products from large to small sizes. Also compatible with water-soluble oil mist.

• air conditioning

Explanation of the test results divided into five categories: pH, total hardness, electrical conductivity, evaporative residue, and others!

• Contract measurement

We will introduce a case where the components of the lubricant were analyzed and the degree of deterioration was confirmed, along with seven analysis items.

• Contract measurement

This is an introduction to a case study analyzing the proportion of diesel fuel mixed in engine oil (dilution rate).

• Contract measurement

Explanation with photos! After polishing the steel plate and applying the test solution, we let it sit and observed the occurrence of rust.

• Contract measurement

Explanation with photos! The test solution was taken in a graduated cylinder and shaken under specific conditions.

• Contract measurement

We provide a clear explanation of appearance and contamination mass methods along with photographs.

• Contract measurement

Introduction of a case where contaminating bacteria were detected in water-soluble cutting oil, along with explanations and photos!

• Contract measurement

Measuring the oil residue attached to metal parts! We provide a clear explanation along with photos.

• Contract measurement

Dynamic balance adjustment service

• Contract measurement

Attach strain gauges that are orthogonal to the center of the specimen, or uniaxial gauges at 0° and 90°, to measure longitudinal and transverse strain.

• Contract measurement

Measure the behavior changes during cooling [P (pressure) - V (volume) - T (temperature)] and use it as simulation data for flow analysis and mold design.

• Contract measurement

20mm vertical burning test (IEC 60695-11-10 Method B, ASTM D3801)

• Contract measurement

Horizontal combustion test (IEC 60695-11-10 Method A, ASTM D635)

• Contract measurement

Vertical Combustion Test for Thin Materials (ASTM D4804)

• Contract measurement

125mm vertical combustion test (IEC60695-11-20, ASTM D5048)

• Contract measurement

Horizontal combustion test of foamed materials (ISO 3582, JIS K6400-6, ASTM D4986)

• Contract measurement

The oil temperature is raised at a constant rate (120°C/h), and a specified bending stress is applied to the sample, with the temperature at which the specified deflection is reached being defined as ...

• Contract measurement

The temperature at which the penetration depth of a needle with a cross-sectional area of 1 mm² reaches 1 mm under a specified load, while the oil temperature is steadily increased in the oil, is refe...

• Contract measurement

It is represented as BPT when a φ5mm steel ball is pressed with a load of 20N for 1 hour in oil at the test temperature, resulting in a sample indentation depth of 0.209mm.

• Contract measurement

The temperature that causes destruction with a 50% probability during impact testing in low temperatures with methanol/dry ice is referred to as the embrittlement temperature.

• Contract measurement

The glass transition temperature of the resin, as well as measurements of viscosity during melting, thermosetting behavior, and steady-state flow viscosity, can be performed.

• Contract measurement

This is a method for measuring accurate thermal conductivity without performing absolute measurements of heat quantity, by simultaneously measuring a reference sample with known thermal conductivity.

• Contract measurement

Measure the electrical resistance using an insulation resistance meter between the circular electrodes, and determine the volume resistivity and surface resistivity from the electrode shape.

• Contract measurement

While the volume resistivity and surface resistivity reflect the shape factors of the test specimen, the insulation resistance is directly indicated by the resistance value (Ω) between the tapered pin...

• Contract measurement

It is a standard for conductive rubber, but it is applied to resistance measurement of conductive plastics.

• Contract measurement

Place four needle-shaped electrodes in a straight line on the sample, pass a constant current between the outer two probes, measure the potential difference that occurs between the inner two probes, a...

• Contract measurement

Using the mutual induction bridge method, the dielectric constant and dielectric loss tangent are determined from the capacitance and conductance of the measurement object at equilibrium.

• Contract measurement

Apply a commercial frequency voltage of 50Hz or 60Hz across the electrodes with the test specimen in between, and determine the voltage that causes the sample to break down.

• Contract measurement

An arc discharge is generated at a specified interval between two tungsten electrodes on the surface of the test specimen, and the time until the sample breaks and the arc discharge disappears is also...

• Contract measurement

Apply a voltage between the platinum electrodes and drip the electrolyte until tracking failure occurs. Evaluate at a voltage that does not cause failure with the specified number of drips.

• Contract measurement

Charge Decay Measurement Device STATIC HONESTMETER Type S-5109 (Manufactured by Shishido Electrostatic Co., Ltd.)

• Contract measurement

It is possible to evaluate the electrostatic properties of polymer materials.

• Contract measurement

Measurement of injection flow length using spiral flow.

• Contract measurement

If you need to measure thermal conductivity, leave it to us.

• Contract measurement

Check trends in the location and size of internal defects with CT scans! Introducing our quality assurance.

• Contract Inspection
• Contract Analysis
• Contract measurement

We will provide various validation services that meet different standards.

• Other clean room equipment and facilities
• Contract Inspection
• Contract measurement

Analyze the filter after resin circulation as needed! Supporting optimal operation for our customers.

• Analytical Equipment and Devices
• Contract measurement
• filter

Surely realize your business ideas! Introduction of evaluation cases for solvent-free UV-curable coatings.

• Contract Inspection
• Contract measurement

Comprehensive evaluation of the potential of the relevant mining area! There is a wealth of experience in various countries and fields.

• Contract measurement

It is possible to estimate the curing time of epoxy resin from the DSC measurement results. We will simulate using the Kamal model.

• Contract Analysis
• Contract measurement
• Other polymer materials

Acquisition of ISO/IEC 17025 laboratory accreditation! Reliable testing services through a controlled environment and established procedures.

• Contract Analysis
• Contract measurement
• Contract Inspection

Effective for identifying defects in semiconductors and electronic components, as well as measuring current distribution in new materials!

• Contract Analysis
• Contract measurement
• Contract Inspection

Increase the reliability of measurement results with high-performance scanning! We also accept requests for measurements only.

• 3D measuring device
• Contract measurement
• Other measurement, recording and measuring instruments

Floor subsidence caused by earthquakes and ground sinking. The subsidence correction specialist, Upcon, will fix the existing floor without demolition and in a short period! Over 3,000 successful case...

• Contract measurement

Providing 3D CAD data quickly with high-precision scanning. For evaluation of prototypes and reverse engineering, etc.

• Contract measurement