サカタ製作所 Product Lineup

To install metal standing seam roofs, a variety of specialized construction hardware is required. Our company is an expert in this field as a "manufacturer of construction hardware specialized in metal standing seam roofs." In this catalog, we introduce "special hardware for overlapping standing seams," "special hardware for snap-lock standing seams," and "accessory materials." We also provide information about the matching site "Mitsukuru," which specializes in metal roofing and wall construction. We encourage you to take a look. [Contents (partial)] ■ How to read the catalog ■ Table of contents ■ Special hardware for overlapping standing seams ■ Special hardware for snap-lock standing seams ■ Accessory materials *For more details, please refer to the PDF document or feel free to contact us.

• Other work tools

We would like to introduce the "Walkway Installation Unit on Standing Seam Roof" that we handle. The target roof is the Type II standing seam. The flow direction consists of components at the seam fastening part, the end, and the middle section, while the span direction is composed of the middle and end sections. Please feel free to contact us when you need assistance. 【Walkway Specifications (Partial)】 ■ Model: MN250-40-2.0 ■ Plate Thickness: 2.0mm ■ Height: 40mm ■ Fixed Span: Within 1,300mm ■ Load Capacity: 150kg (1471N) or less *For more details, please refer to the PDF document or feel free to contact us.

• Solar power generator

Our company handles a variety of auxiliary materials related to metal standing seam roofs. The "insulation fittings" are used to place insulation material between the seams to suppress heat conduction when installing a double-layer roof. By doing so, it is expected to reduce the air conditioning load. In addition, we offer a wide range of products such as "snow stop fittings," which are installed to prevent snow from sliding off easily from the standing seam, and "re-roofing fittings," which are used when installing a new roof over an aging roof. Please feel free to contact us. 【Features】 ■ Snow Stop Fittings - Installed to prevent snow from falling off easily from the standing seam. - The type of fittings used varies depending on the type of standing seam. ■ Re-roofing Fittings - Used when installing a new roof over an aging roof. - Double-layer roofing takes less time and cost than removing the existing roof and installing a new one. *For more details, please refer to the PDF materials or feel free to contact us.

• others

The folded plate is primarily developed with a focus on the structure of its cross-section and is widely used in steel buildings such as factories, carports, and warehouses. It is a representative roofing method for metal roofs. The "haze-type folded plate" involves a processing technique called "haze" at the joints of the folded plate body, and the tight frame and the folded plate body are fixed with a fitting called "tsuruko." As a final step, tightening the haze is necessary. Our company offers a variety of fittings specifically for haze-type folded plates. Please feel free to contact us if you need assistance. 【Components of Haze-Type Folded Plate Roof (Partial)】 ■ Apron face ■ Tight frame ■ Decorative frame ■ Reinforcement leg ■ Ridge tight frame *For more details, please refer to the PDF materials or feel free to contact us.

• others

The folded plate is primarily developed with a focus on the structure of its cross-section and is widely used in steel buildings such as factories, carports, and warehouses. It is a representative roofing method for metal roofs. The "overlapping folded plate" method involves penetrating the folded plate body with a tight frame's sword tip bolt and tightening it with nuts, washers, and packing. It is orthodox and is used in relatively small warehouses, factories, and carports. Our company offers a variety of fittings specifically for overlapping folded plates. Please feel free to contact us when needed. 【Components of Overlapping Folded Plate Roof (Partial)】 ■ Apron face (ridge face) ■ Decorative frame ■ Eaves roof (suspended folded plate) ■ Water surface (stop) face ■ Gable frame *For more details, please refer to the PDF materials or feel free to contact us.

• others

The "Earth Connector" is a component that connects solar panel modules without any wiring. The installation of this product may cause small scratches on the plated and painted parts of the rack components and solar brackets, but these scratches do not significantly impair the corrosion resistance of the solar brackets. In this document, we conducted a "composite cycle test" to confirm the conductivity of the module frame. For more details, please refer to the related catalog below. [Contents] ■ Composite Cycle Test Results *For more information, please refer to the PDF document or feel free to contact us.

• Assembly Jig
• Other machine elements
• others

In this document, we introduce the "corrosion resistance of snow stop fittings." To simulate and promote natural environmental conditions, we conduct a corrosion testing method called "composite cycle testing," which involves repeated cycles of salt spray, drying, and wetting. One cycle consists of salt spray for 2 hours, drying for 4 hours, and wetting for 2 hours, totaling 8 hours. The test results are published for cycles 0, 60, and 120, so please take a look. [Contents] ■ Testing Method ■ Test Results *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Jig
• Other machine elements
• others

There are cases where the corrosion of mounting brackets is accelerated by the water flow accumulated on solar panels. In this document, we will introduce the measures against water rust for our mounting bracket "Haze Type High Strength Solar Bracket." Please take a look at the related catalog below for more information. *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Jig
• Other machine elements
• others

Sakata Manufacturing is a specialized manufacturer focused on components that support metal roofs, receiving significant support from across the country. In the field of renewable energy (solar power generation), we also utilize our expertise in metal roofing. This catalog introduces "mounting brackets and frames" for solar panels. We invite you to read it. [Contents (partial)] ■ Sakata Manufacturing supports both roofs and solar power ■ Reasons why Sakata is chosen ■ Table of contents ■ Roof type and solar panel type identification chart ■ Examples of implementation *For more details, please refer to the PDF document or feel free to contact us.

• nut
• Other machine elements
• others

Just attach it to your drill driver! Rust removal from bolts is completed in seconds!! It is powerful for reusing embedded bolts and removing nuts from rusty bolts!!

• bolt

We would like to introduce our insulation fittings, "Dankichi HQ/HQS/HQIII type." "Dankichi HQ" features a box-shaped design that enhances strength and stability. The stopper function allows the fitting to remain open, eliminating the need to loosen the nut and perform the operation with both hands. Additionally, "Dankichi HQS" is recommended for projects requiring negative pressure (tensile) strength, while "Dankichi HQIII type" is designed for a socket size with a side length of 17mm. 【Features】 <Dankichi HQ> ■ Excellent strength and durability ■ Box-shaped design improves strength and stability ■ Easy installation with the stopper function *For more details, please refer to the PDF document or feel free to contact us.

• others

We would like to introduce the "Kaku Haze V-1 Type Tight Frame" that we handle. This is a construction hardware for trapezoidal sheet roofs, equipped with a washer nut suspension set. The integration of the suspension and reinforcement hardware has improved workability. The main material is galvanized steel sheet, and you can choose from three thicknesses: 2.5, 2.8, and 3.2 mm. Please feel free to contact us when you need assistance. 【Features】 ■ Comes with a washer nut suspension set ■ Main material: Galvanized steel sheet ■ Suspension material: Galvanized steel sheet and stainless steel ■ Bolt and nut: Iron (chromate) M10 ■ Main sheet thickness (t): 2.5, 2.8, 3.2 *For more details, please refer to the PDF document or feel free to contact us.

• others