新明工業 List of Products and Services

The "Medium Load Drive Roller Conveyor" is a transport device suitable for E/G assembly lines. It rotates the rollers through belt drive, allowing pallets to be transported at a constant speed. Since it uses rollers, it can accommodate changes in pallet width. 【Specifications】 ■ Load capacity: 60kg ■ Pallet width: 300–500mm ■ Pallet length: 250–500mm ■ Motor specifications: AC200V induction motor ■ Conveyor speed: 12m/min *For more details, please refer to the PDF document or feel free to contact us.

• Conveyor

The "Leak Full Length Measuring Machine" is an assembly machine suitable for hydrogen tank assembly lines. It inspects the leak (leakage) of the tank (liner assembly) while measuring the full length of the workpiece. 【Specifications】 ■ Equipment size: Width 4060mm × Depth 1620mm × Height 1500mm ■ Cycle time: 238 seconds ■ Conveying height: 620mm ■ Tank length: Compatible with 680 to 1470mm *Automatic size change ■ Tank outer diameter: φ300mm ■ Full length measuring machine ・ Minimum detectable object: 0.3mm ・ Measurement accuracy: ±0.15μm *For more details, please refer to the PDF document or feel free to contact us.

• Other assembly machines

The "Anti-adhesion Agent Coating Machine" is suitable for the hydrogen tank assembly line. The transport height is 620mm, and it accommodates tank lengths from 680 to 1470mm. It applies an anti-adhesion agent to the surface of the tank (liner assembly) and dries it. 【Specifications】 ■ Equipment size: Width 5110mm × Depth 3850mm × Height 1900mm ■ Cycle time: 238 seconds ■ Transport height: 620mm ■ Tank length: Accommodates 680 to 1470mm *Automatic size change ■ Tank outer diameter: φ300mm ■ Heater capacity: 20kW × 3 units *Air supply uses factory air ■ Primary power supply: AC200V 80KVA ■ Air pressure: 0.35 to 0.5MPa *For more details, please refer to the PDF document or feel free to contact us.

• Other processing machines

The "FW Fiber End Processing Machine" is suitable for hydrogen tank assembly lines. It accommodates tank lengths from 680 to 1470 mm, and tank outer diameters up to φ300 mm. The end parts of the FW fibers are partially cured with heat to prevent fiber peeling. 【Specifications】 ■ Equipment size: Width 3100 mm × Depth 2900 mm × Height 1500 mm ■ Cycle time: 374 seconds ■ Conveying height: 620 mm ■ Tank length: Accommodates 680 to 1470 mm *Automatic size change ■ Tank outer diameter: Accommodates up to φ300 mm ■ Primary power supply: AC200V 8.6KVA ■ Air pressure: 0.35 MPa *For more details, please refer to the PDF document or feel free to contact us.

• Other processing machines

The "adhesive application machine" is suitable for the hydrogen tank assembly line. The cycle time is 238 seconds, and the work set height is 900mm. Adhesive is applied inside the protective layer (protector). 【Specifications】 ■ Equipment size: Width 1000mm × Depth 3250mm × Height 1600mm ■ Cycle time: 238 seconds ■ Work set height: 900mm ■ Protective layer size: φ300mm ■ Application machine: Single-component quantitative booster (maximum discharge volume 17cc) ■ Primary power supply: AC200V 3.6KVA *For more details, please refer to the PDF document or feel free to contact us.

• Other processing machines

The "Protective Layer Assembly Machine" is suitable for hydrogen tank assembly lines. It accommodates tank lengths from 680 to 1470 mm and external diameters up to φ300 mm. The protective layer (protector) is assembled at two locations on the E.V. side, at both ends of the tank. 【Specifications】 ■ Equipment size: Width 4400 mm × Depth 1510 mm × Height 1500 mm ■ Cycle time: 238 seconds ■ Conveying height: 620 mm ■ Tank length: Accommodates from 680 to 1470 mm *Automatic size change ■ Tank external diameter: Accommodates up to φ300 mm ■ Tank weight: 50 kg ■ Primary power supply: AC200V 9.4KVA *Airless specification *For more details, please refer to the PDF document or feel free to contact us.

• Other processing machines

The "Collecting Terminal Assembly Machine" is suitable for battery assembly lines. It features a high-speed transport system using a linear conveyor module. The assembly jig can be stopped at any position to perform the assembly of collecting terminals, as well as the assembly and press-fitting of gaskets and covers. 【Overview】 <Specifications> ■ Cycle Time: 3s per unit ■ Size: Width 547mm × Height 1900mm × Depth 2805mm <Main Equipment Used> ■ Jig Transport: LCM-X ■ Parts Feeder: 1 unit (gasket) ■ Scara Robot: 3 units (collecting terminal positive and negative poles, cover) YK600XGH-200-F ■ Image Processing Camera: 1 unit (cover assembly) *For more details, please refer to the PDF document or feel free to contact us.

• Other processing machines

The "Insulator and Z Terminal Assembly Machine" is suitable for battery assembly lines. It allows the assembly jig to stop at any position to perform insulator assembly and press-fitting, bolt assembly, and Z terminal assembly. It features a high-speed transport system using a linear conveyor module. 【Overview】 <Specifications> ■ Cycle Time: 3s per unit ■ Size: Width 5396mm × Height 1900mm × Depth 2800mm <Main Equipment Used> ■ Assembly Jig Transport: LCM-X ■ Parts Feeders: 3 units (insulator positive and negative terminals, bolts) ■ Scara Robots: 2 units (YK600XGH-200-F for Z terminal positive and negative terminals) ■ Image Processing Cameras: 2 units (for Z terminal positive and negative assembly) *For more details, please refer to the PDF document or feel free to contact us.

• Other processing machines

The "crimping machine" is a lid assembly machine suitable for battery assembly lines. It stops the assembly jig at a designated position and performs the crimping process and work transfer to the carrier. Variations are measured using a contact-type displacement sensor, and adjustments to the crimping height are made. 【Overview】 <Specifications> ■ Cycle time: 3s per unit ■ Size: Width 2990mm × Height 2050mm × Depth 1374mm <Main Equipment Used> ■ Assembly jig transport: LCM-X ■ Crimping units: 3 units *For more details, please refer to the PDF document or feel free to contact us.

• Other conveying machines

The "buffer conveyor" is suitable for battery assembly lines. It can store a buffer to accommodate stoppages due to component exchanges between the front and rear equipment in the lid assembly process of lithium batteries. 【Specifications】 ■ Cycle time: 3s/unit ■ Size: Width 1900mm × Height 1104mm × Depth 755mm ■ Maximum carrier stock number: 60 *For more details, please refer to the PDF document or feel free to contact us.

• Conveyor

This product is a cleaning machine suitable for battery assembly lines. It removes foreign substances attached to parts using air blow, and cleans the workpiece by inverting it and using 15 air nozzles. The sealed structure allows air to flow from the top to the bottom, preventing dust from reattaching. 【Specifications】 ■ Cycle time: 3s/piece ■ Size: Width 2865mm × Height 2066mm × Depth 1520mm ■ Air blow nozzles: 15 *For more details, please refer to the PDF document or feel free to contact us.

• Other cleaning machines

This product is an integrated machine suitable for battery assembly lines. It disassembles 10 layers of empty containers step by step, packs the completed lid parts into containers, and then stacks them back into 10 layers for dispatch. 【Specifications】 ■ Cycle time: 3s/item (54 items per container) ■ Size: Width 3784mm × Height 1800mm × Depth 1956mm ■ Number of empty containers to be input: 20 (10 layers × 2 stacks) ■ Number of completed containers on standby: 20 (10 layers × 2 stacks) *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

The "Rear Suspension Assembly Device & Conveyor" is suitable for vehicle assembly lines. It can accommodate various configurations, including loop type, reciprocating type, and combinations with various fastening tools and nut runners. The rear suspension and engine assembly are mounted on the suspended body. 【Specifications】 ■ Machine Size: Depth 2500mm × Width 1500mm × Height 600mm ■ Lifter Stroke: 1200mm H = 650mm to 1850mm ■ Lifter: Hydraulic type / Electric type ■ Lifter Capacity: 2500kgf ■ Travel Speed: 500mm/s ■ Lifting Speed: 250mm/s *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

We introduce various fastening devices suitable for vehicle assembly lines. Tightening operations for body and suspension components are carried out. Various fastening tools can be combined with nut runners. There are simple types using aluminum erectors and types equipped with coil compression functions. 【Specifications】 ■ Machine size: Depth 1650mm × Width 700mm × Height 1600mm ■ Tightening torque: 216–294 N·m ■ Nut runner: Atlas Copco *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

We introduce various types of press-fitting machines suitable for vehicle assembly lines. Press-fitting of the bushings (cushions) at the connection points of the front and rear suspension members to the body. Compatible with hydraulic and electric systems, ensuring safety with various covers and sensors. 【Specifications】 ■ Machine size: Depth 1100mm × Width 1100mm × Height 1400mm ■ Press-fitting source: Hydraulic / Electric press ■ Press-fitting cycle: 15 seconds to 65 seconds ■ Press-fitting load: 100kN *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

Introducing the "Oil Injection Device & Guarantee Device" suitable for vehicle assembly lines. The "Oil Injection Device" injects various oils from the oil supply room or drums into the transaxle, transfer case, differential, etc. The "Oil Guarantee Device" checks for the presence of oil using a fiber sensor. 【Specifications】 ■ Machine Size: Depth 1500mm × Width 670mm × Height 1800mm ■ Power Source: Air (High Pressure 0.6MPa, Low Pressure 0.3MPa) ■ Injection Cycle (Approx.): 4000g (just under 5000cc) in 12 seconds at high pressure, 15 seconds at low pressure ■ Injection Gun: The nozzle part is designed according to the target work each time *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

The "trolley transport conveyor" is suitable for vehicle assembly lines. It connects the preparation trolley and ribbon steel, driving the ribbon steel by pinching it with polyurethane rollers, allowing for various layouts and combinations of continuous feeding and STOP & GO. Additionally, it is a patented product. 【Specifications】 ■ Pulling capacity: approximately 100 kgf with a 0.2 kW reducer ■ Transport speed: 250 mm/s ■ Minimum conveyor height: 200 mm *For more details, please refer to the PDF document or feel free to contact us.

• Conveyor

The "jig pallet transport conveyor" is suitable for vehicle assembly lines. It can accommodate various types according to specifications, such as free flow conveyors and roller conveyors. It is a heavy-duty type designed to transport jig pallets. 【Specifications】 ■Transport speed: MAX 250mm/s ■Transport capacity: MAX 700kg ■Conveyor length: 4000mm *For more details, please refer to the PDF document or feel free to contact us.

• Conveyor

The "Alignment Adjustment Device" is suitable for vehicle assembly lines. It reproduces the loaded state (coil compression) to measure the wheel's camber angle and caster angle, and adjusts and tightens the cam bolts. There is a lineup of both automatic and manual machines. 【Specifications】 ■ Machine size: Depth 6000mm × Width 3850mm × Height 1600mm ■ Work input method: Loader automatic input ■ MAX tact (adjustment time): 31 seconds *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

This product is a cart suitable for vehicle assembly lines. It is used for preparation processes of various units before vehicle installation and can be combined with AGVs and our various preparation conveyors, as well as being used as a hand-pushed cart. Please feel free to contact us when you need assistance. *For more details, please refer to the PDF materials or feel free to contact us.

• Trolley

The "Man Conveyor" is suitable for vehicle assembly lines. The belts are available in plastic and resin types. They transport people and carts at the same speed as the products in the flow process. 【Specifications】 ■ Width: up to 3000mm ■ Length: up to 50000mm ■ Speed: 100mm/s *For more details, please refer to the PDF document or feel free to contact us.

• Conveyor

This product is a simple type of auxiliary lifting device that uses an air balancer, etc. It can lift items weighing up to 60 kg with a weight of 7 kg or less, and it is also compatible with air tank-mounted types. We offer various types including "suspension type," "ground traveling type," and "pole type (jib crane type)." 【Specifications】 ■ Machine size: Depth 800mm × Width 800mm × Height 820mm ■ Lifting stroke: 1000mm *For more details, please refer to the PDF document or feel free to contact us.

• Other conveying machines

We would like to introduce our "jig pallet" suitable for vehicle assembly lines. These are trays for preparation processes and installation of various units such as rear suspension, engine, hydrogen tank, etc., before vehicle installation. 【Various Units】 ■ Front Suspension ■ Rear Suspension ■ Engine ■ Fuel Tank ■ Hydrogen Tank, etc. *For more details, please refer to the PDF materials or feel free to contact us.

• Inspection fixture

The "Steering Angle Inspection Device" is suitable for vehicle assembly lines. It measures the maximum steering angle of the vehicle's front tires and determines pass or fail. Additionally, it performs headlamp alignment, camera calibration, millimeter-wave learning, and rear millimeter-wave learning through the vehicle alignment mechanism. 【Specifications】 ■ Machine Size: Depth 6500mm × Width 3000mm × Height 2000mm ■ Allowable Axle Load: 1500kgf for both front and rear wheels ■ Wheelbase Compatibility Range: 2400mm to 3200mm ■ Tread Compatibility Range: 1350mm to 1650mm ■ Tire Steering Angle Compatibility Range: ±50° ■ Vehicle Alignment Accuracy: ±0.5° ■ Measurement Accuracy: ±0.1° *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Side Slip Inspection Device" is suitable for vehicle assembly lines. It measures the lateral slip of the tires during straight driving and determines pass or fail. The allowable axle weight is MAX 1500kgf, and the measurement range is 0±10mm/m. 【Specifications】 ■ Machine size: Depth 1500mm × Width 2500mm × Height 350mm ■ Allowable axle weight: MAX 1500kgf ■ Tread compatibility range: 1400mm to 1750mm ■ Measurement range: 0±10mm/m ■ Measurement accuracy: Front and rear wheel stress during vehicle operation ±0.1m ■ Passing speed determination: Yes *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Headlight Inspection Device" is suitable for vehicle assembly lines. It checks the brightness and direction of the headlights and determines pass or fail. Adjustments are made automatically with specialized hand tools. The maximum vehicle passage width is 2400mm, and the compatible light sources for the headlamps are halogen, HID, and LED. 【Specifications】 ■ Machine size: Depth 2500mm × Width 3800mm × Height 2000mm ■ Focusing lens movement range - X-axis Original position 0–2400mm - Y-axis Original position ±250mm - Z-axis Original position 0–700mm ■ Vehicle passage width: MAX 2400mm ■ Measurement content: Headlamp optical axis height ■ Compatible light sources for headlamps: Halogen, HID, LED ■ Fog light compatibility: Available (optional) *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Speedometer Inspection Device" is suitable for vehicle assembly lines. It allows vehicles to be driven on a drum roller under conditions close to actual driving, such as equivalent inertia weight suitable for the vehicle's weight, to perform driving checks and meter checks. 【Specifications】 ■ Machine size: Depth 7500mm × Width 3200mm × Height 1300mm ■ Allowable axle load: 1500kgf for both front and rear wheels ■ Equivalent inertia weight: 800kgf to 1800kgf (fixed) / Supports two-stage variable (mechanical) ■ Wheelbase range: 2400mm to 3700mm ■ Tread range: 1400mm to 1750mm ■ Maximum test speed: MAX 160km/h, capable of 200km/h (optional) *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Brake Testing Device" is suitable for vehicle assembly lines. It drives the rollers to rotate the car's tires and measures the braking force applied by the driver to determine pass or fail. The inspection items include dragging, braking force, parking brake, and ABS. 【Specifications】 ■ Machine size: Depth 6000mm × Width 3600mm × Height 1900mm ■ Allowable axle weight: 1500kgf for both front and rear wheels ■ Roller size: φ185mm for both front and rear, Width 700mm ■ Wheelbase range: 2400mm to 3200mm ■ Tread range: 1400mm to 1800mm ■ Inspection items: dragging, braking force, parking brake, ABS ■ Measurement accuracy: ±5% *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Noise Inspection Device" is suitable for vehicle assembly lines. It inspects interior noise during actual driving conditions using uneven surfaces installed on a drum roller. There are two types of inspection: one is manual inspection by driving, and the other is automatic inspection by rotating the drum roller with a motor. 【Specifications】 ■ Machine Size: Depth 6400mm × Width 4000mm × Height 2200mm ■ Allowable Axle Weight: 1700kgf for both front and rear wheels ■ Wheelbase Compatibility Range: 2400mm to 3200mm ■ Tread Compatibility Range: 1400mm to 1750mm ■ Maximum Test Speed: MAX 35km/h ■ Road Surface Patterns: Rope road, cobblestone road, undulating road *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Alignment Inspection Device" is suitable for vehicle assembly lines. It measures the front wheel's toe, camber, caster, and the rear wheel's toe and camber without contact. Specifications can be adjusted using tire guides, tread, and wheelbase switching mechanisms. 【Specifications】 ■ Machine size: Depth 6500mm × Width 3500mm × Height 2200mm ■ Allowable axle weight: 1500kgf for both front and rear wheels ■ Wheelbase adjustment range: 2400mm to 3200mm ■ Tread adjustment range: 1350mm to 1650mm ■ Compatible tire outer diameter size: φ560mm to φ760mm ■ Runout speed: MAX 10km/h ■ Measurement method: Non-contact laser sensor ■ Measurement accuracy: ±0.05° *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Fully Automatic Alignment Adjustment Machine" is suitable for vehicle assembly lines. It automatically performs all operations for adjusting and tightening the front and rear toe based on the toe values measured by the alignment inspection device. We recommend a combined introduction with the alignment inspection device. 【Specifications】 ■ Machine Size: Depth 7500mm × Width 3200mm × Height 2000mm (with built-in alignment tester) ■ Allowable Tightening Torque: Front Wheels 80N·m, Rear Wheels 80N·m ■ Wheelbase Compatibility Range: 2400mm to 3200mm ■ Tread Compatibility Range: 1350mm to 1650mm ■ Compatible Tire Outer Diameter Size: φ560mm to φ760mm ■ Runout Speed: MAX 10km/h ■ Vehicle Alignment Accuracy: ±0.3° *For more details, please refer to the PDF document or feel free to contact us.

• Other inspection equipment and devices

The "Vehicle Alignment Device" is suitable for vehicle assembly lines. It aligns the vehicle by pushing the tires from the inside. The tire passage height is designed to be low, eliminating the need for an embedded pit. There are two types: air-operated and electric. 【Specifications】 ■ Machine size: Depth 9000mm × Width 5000mm × Height 150mm ■ Maximum axle load: MAX 2500kgf ■ Wheelbase compatibility range: 2400mm to 3200mm ■ Tread compatibility range: 1250mm to 1750mm ■ Tire width compatibility range: 155mm to 255mm ■ Vehicle alignment accuracy: ±0.3° (vehicle off-center) *For more details, please refer to the PDF document or feel free to contact us.

• Assembly Machine

It is possible to create original vehicles tailored to specific purposes and needs. Ensuring the safety of passengers is also a feature. Specifications ◆ Installation of an 8-point roll bar (including body reinforcement) ◆ Installation of a carrier-type roof guard (floorboard: Hardox plate) ◆ Installation of a front grill guard and front wind guard ◆ Installation of a front wind mesh guard ◆ Installation of a steel plate under cover ◆ Installation of LED work lights and a single beacon lamp

• others

Our "Frozen Bike" operates the compressor using electricity, allowing it to run with zero gasoline and exhaust emissions. Additionally, it has low engine load, contributing to reduced running costs. *Production and sales will take place in Indonesia. *For more details, please download the materials or contact us through our website.

• others

We respond to requests from the concept of various automated machines and labor-saving devices to design and manufacturing, creating something new from scratch. <Production Flow> ■ Meeting: Develop a detailed plan from specific discussions ■ Proposal 1: Present an outline of usage and conceptual drawings ■ Proposal 2: Conduct specifications meeting and provide a rough estimate ■ Design: Carry out detailed design ■ Delivery: Manufacturing, assembly, debugging, and installation

• Other processing machines

This is a low-cost, high-effect bio cleaner that can be discharged while still in a state of oil decomposition. It has received numerous environmental technology awards worldwide. 〈Specifications〉 ◆ Cleaning power similar to alkaline detergents ◆ Reduces burden on the materials being cleaned (Prevents deterioration of pit paint and discoloration of wheels) ◆ Removes odors simultaneously with oil decomposition (also reduces cigarette smell) ◆ The work itself is simple and hassle-free ◆ Gentle on the environment and human body, no worries about skin irritation even when handled with bare hands ◆ Cost reduction possible due to 20-40 times dilution (41-81 yen per liter)

• Cleaning agents

We offer a wide range of automotive parts for the aftermarket, from automotive repair parts and car accessories to automotive maintenance-related equipment. *For more details, please contact us through our company website.*

• Other Auto Parts

We deliver a variety of automotive parts for the aftermarket. We offer a wide range of products, from automotive repair parts and car accessories to automotive maintenance-related equipment.

• Other Auto Parts

By not placing luggage under the passenger seat, we ensure visibility through the safety window. The storage box is sliding, making it easy to load and unload luggage without stepping on it. 〈Specifications〉 Size of the sliding box: Length 54cm × Width 38cm × Height 38cm Sliding box: Made of durable, lightweight fabric Maximum weight of stored luggage: 20kg ◆ Allows visibility of the safety window without obstructing the driver's view ◆ Comes with an adjustable belt that can be attached to the seatbelt ◆ Equipped with a lid to prevent items from falling out *For more details, please contact us through our website.

• others

We offer a wide range of automotive parts for the aftermarket, from automotive repair parts and car accessories to automotive maintenance-related equipment. ■ Genuine parts from automotive manufacturers Toyota, Nissan, Honda, Daihatsu, Mitsubishi, Mazda, Subaru, Suzuki, etc. ■ Quality manufacturer parts Advics, Tokico, Miyako Automotive Industry, Musashi Oil Seal, Ohno Rubber, etc. ■ Rebuilt manufacturers Japan Rebuilt, Turbo Techno, Ernest

• Other Auto Parts

We deliver a variety of automotive parts for the aftermarket. We offer a wide range of products from automotive repair parts and car accessories to automotive maintenance-related equipment. <Specifications> - Car Navigation Panasonic, Pioneer, Kenwood, Alpine, Eclipse - ETC Panasonic, Pioneer, Kenwood, Alpine, etc. - Dash Cameras, Radar Detectors, Engine Starters, Theft Alarms Comtec, Yupiteru, Celstar, Kato Electric

• Interior parts

To operate the compressor with electricity, gasoline and exhaust emissions are zero. The engine load is also low, which reduces running costs. *Production and sales will take place in Indonesia.* <Specifications> Body type: Refrigerated box Internal dimensions: 3.0m³ (L=2000mm, W=1500mm, H=1000mm) Operating temperature: -18℃ to +20℃ Refrigerant used: R134a Power source: DC12V-700W / AC220V-700W Payload: 800kg *Production and sales will take place in Indonesia.*

• others

To operate the compressor with electricity, there are zero gasoline and exhaust emissions. It is a large refrigerated truck with low engine load and reduced running costs. *Production and sales will take place in Indonesia.

• others

A lightweight fire truck that is effective in densely populated residential areas and mountainous regions. It can be boarded while wearing a helmet and, despite its compact size, accommodates four passengers along with firefighting equipment. <Specifications> ◆ Equipped with essential firefighting gear such as pumps, suction hoses, and nozzles ◆ Utilizes a cold-weather chassis designed for firefighting, making it suitable for use anywhere in the country ◆ Long items such as hoses and ladders can be mounted on the top of the vehicle ◆ Features a unique pump rail designed by Shinmei that allows for the mounting of various pumps and makes loading and unloading easy with an inclined rail ◆ No need for a medium or semi-medium license; anyone can drive it.

• others

This is a workbench for manual assembly and manual bolt fastening. The nut runner is equipped with weight assistance from a spring balancer. <Specifications> Nut runner: NA979-C00-0 (Estic)

• Other work tools