篠原電機 List of Products and Services

The "SSH Type and TSSH Type Space Heater Specifications" are equipped with a heat dissipation cover attached to the space heater, which can be used to prevent condensation and reduce humidity inside the panel. By using the space heater, the total length is shortened by only 200W, allowing for space-saving solutions. This product incorporates a space heater into a heat dissipation cover made of punched steel plate, making it easy to install with four screws. 【Features】 ■ Shortened total length for space-saving solutions ■ Space heater integrated into a punched steel plate heat dissipation cover ■ Easy installation with four screws *For more details, please refer to the PDF document or feel free to contact us.

The "surface heater" is a surface heating element with a patterned nickel alloy resistor arranged between silicone rubber sheets. The outer layer is reinforced with glass cloth, providing excellent mechanical strength. High-efficiency far-infrared radiation is emitted from the surface, making it suitable for far-infrared heating of polymer materials. Compared to conventional ceramic far-infrared radiators, it is lighter, softer, and lower in cost. 【Features (Silicone Rubber Heater)】 ■ Shapes and patterns can be freely designed and manufactured according to application ■ Fits heated surfaces such as curved and cylindrical shapes ■ Excellent thermal responsiveness and rapid heating capability *For more details, please refer to the PDF materials or feel free to contact us.

Since the copper plate and steel plate are brazed together, they will not come apart due to the heat from welding. We offer a variety of options from one hole to four holes, rated for a current of up to 400A. Additionally, the "ECK type" is convenient for use in narrow areas where it is difficult to tighten bolts, such as corner sections. 【Features】 ■ Complies with Ministry of Land, Infrastructure, Transport and Tourism standards ■ Brazed copper and steel plates do not come apart due to welding heat ■ Various options available from one hole to four holes, rated for a current of up to 400A *For more details, please refer to the PDF document or feel free to contact us.

The "ground terminal block" is a terminal block that allows for easy measurement of the resistance on the grounding side by opening the movable bar. By short-circuiting the EA, EB, and ED terminals, the resistance on the grounding side can be easily measured. There is also a type with a two-tier movable bar (AT-200W) available for use according to your conditions. 【Features】 ■ Easy measurement of the resistance on the grounding side by opening the movable bar ■ Easy measurement of the resistance on the grounding side by short-circuiting the EA, EB, and ED terminals ■ A type with a two-tier movable bar (AT-200W) is also available in the lineup ■ The base is available in black and green types *For more details, please refer to the PDF document or feel free to contact us.

The "Back Wiring Type Ground Terminal Block" is a terminal block that allows for easy wiring when using rear-wired devices. By opening the movable bar, it is possible to easily measure the resistance on the ground electrode side. Additionally, by short-circuiting each of the T1, T2, and T3 terminals, the resistance on the ground electrode side can be easily measured. 【Features】 ■ Easy wiring when using rear-wired devices ■ Easy measurement of resistance on the ground electrode side by opening the movable bar ■ Easy measurement of resistance on the ground electrode side by short-circuiting each of the T1, T2, and T3 terminals *For more details, please refer to the PDF document or feel free to contact us.

The "Ground Terminal Panel" is a ground terminal panel based on the "Guidelines for Certification of Cubicle-Type Emergency Power Supply Receiving Equipment" issued by the Japan Electric Association. We use our ground terminal blocks AT-50/100/200. Depending on the application, you can choose from six combinations regarding the number of ground terminal blocks, the presence of separators, and the presence of test terminals. 【Features】 ■ For certified cubicles ■ Uses ground terminal blocks "AT-50/100/200" ■ Choose from six combinations based on application *For more details, please refer to the PDF materials or feel free to contact us.

The "Stud Terminal Block" is a terminal block that can be used as a junction, branch, or support for wires, copper busbars, etc. Without changing the dimensions of the main body, there are three types of screw diameters: M6, M8, and M10. It has excellent insulation properties, is lightweight, and does not break. 【Features】 ■ Choose from three types of screw diameters: M6, M8, and M10 without changing the dimensions of the main body ■ Excellent insulation properties, lightweight, and unbreakable ■ Green type also available for the main body ■ RoHS compliant *For more details, please refer to the PDF document or feel free to contact us.

The "Low Voltage Branch Terminal Block" is a terminal block that can connect up to 7 branches as a low voltage branch terminal block. It has an insulation voltage of 2.5kV and a creepage distance of more than 20mm. 【Features】 ■ Can connect up to 7 branches as a low voltage branch terminal block (for 200A) ■ Insulation voltage of 2.5kV ■ Creepage distance of more than 20mm *For more details, please refer to the PDF document or feel free to contact us.

【Features】 ■Made to order (e.g., AT-200 × 5 units) *For more details, please refer to the PDF document or feel free to contact us.

【Features】 1. The earth wire is built into the plastic pipe, providing excellent insulation and safety. 2. The earth wire and clips at the bottom of the pipe are covered with an insulating tube, allowing for safe use. 3. It is lightweight and easy to operate. 4. The pipe is made of a hazardous color, yellow. *For more details, please refer to the PDF document or feel free to contact us.

The "Parts Box" is a storage box for spare parts used in equipment such as distribution boards, control panels, and operation panels. Made of transparent plastic, the contents can be seen from the outside. The opening and closing mechanism is one-touch, making it easy to access spare parts. It becomes even more convenient when used in combination with a drawing holder. It can be attached with double-sided adhesive tape and can also be secured with screws. It is lightweight and there is no worry about it breaking. 【Features】 ■ Transparent plastic allows visibility of contents from the outside ■ One-touch opening and closing makes it easy to access spare parts ■ Can be attached with double-sided adhesive tape and secured with screws ■ Lightweight with no risk of breaking *For more details, please refer to the PDF document or feel free to contact us.

"Decorative screws" can be used for distribution and control panels, etc. *For more details, please refer to the PDF document or feel free to contact us.

The "Disconnect Switch Hook Rod (Hook Rod for Operating Disconnect Switches)" can be used for opening and closing operations of electrical circuit disconnect switches. 【Features】 1. Complies with JIS-C-4510 standards. 2. Made of plastic, it has excellent insulation properties and is non-absorbent. 3. Lightweight and easy to operate. 4. Uses a danger color yellow pipe. 5. With a pipe diameter of 32mm, it has excellent strength. * The FBK type has a longer hook section, making it easier not only to open and close the disconnect switch but also to operate the cutout. * For more details, please refer to the PDF document or feel free to contact us.

We also offer a "holder and tray for hook rods" that can be used for the opening and closing operation of electrical circuit breakers. 【Features】 ■ For hook rods used in the opening and closing operation of electrical circuit breakers ■ Environmentally friendly, electro-galvanized trivalent chromate treatment *For more details, please refer to the PDF document or feel free to contact us.

The "Hook Stick Display Label" is a label that can be used to indicate storage on a panel equipped with a hook stick for operating circuit breakers. It has been laminated, making it suitable for outdoor use. The base paper is transparent PET, so it blends well with the panel's paint color. It is based on the "Guidelines for Certification of Cubicle-Type Emergency Power Supply Receiving Equipment" published by the Japan Electric Association. 【Features】 ■ Display label based on the "Guidelines for Certification of Cubicle-Type Emergency Power Supply Receiving Equipment" published by the Japan Electric Association ■ Laminated for outdoor use ■ The base paper is transparent PET, ensuring no discomfort with the panel's paint color *For more details, please refer to the PDF document or feel free to contact us.

The "Bracket for Mounting Protection Plates" can be used as a bracket (suspension device) for mounting protection plates (charging area protection barriers) inside cubicles and similar enclosures. 【Features】 1. The protection plate can be suspended, eliminating the need for troublesome processing such as daruma holes. 2. Since it is a suspension type, there is no need for complicated screw processing like tapping on the panel side. (It can be attached with a single touch.) 3. Installation and removal are easy, improving work efficiency and reducing maintenance time for inspections and cleaning. 4. No mounting screws are required, so there is no worry about losing screws during work, allowing for safe operations. 5. Products with insulated protection plates (barrier plates) can also be manufactured. Please specify the dimensions. *For more details, please refer to the PDF materials or feel free to contact us.

The "SS Bushing" can be used as an introduction bushing for the lock shaft that opens and closes the doors of distribution boards and similar equipment. 【Features】 1. When locking the door, the taper of the "bushing" smoothly guides the shaft into the lock hole. 2. It prevents noise caused by vibrations. 3. It eliminates paint peeling around the lock hole due to the opening and closing of the lock shaft, preventing rust formation. 4. The installation of the SS bushing can be done with a simple push, making it a one-touch operation. *For more details, please refer to the PDF document or feel free to contact us.

The "Card Holder (Adhesive Fixed Type with Screw Combination)" has a strong double-sided adhesive tape applied to the back, providing very strong adhesion and eliminating the need for drilling holes and tapping. It does not corrode the adhesive surface. It is resistant to temperature and humidity, and can easily adapt to slightly rough surfaces while also allowing for screw installation. 【Features】 ■ Strong adhesion due to the double-sided adhesive tape on the back ■ Eliminates the need for drilling holes and tapping ■ Does not corrode the adhesive surface ■ Resistant to temperature and humidity, and can easily adapt to slightly rough surfaces while allowing for screw installation *For more details, please refer to the PDF document or feel free to contact us.

The "Card Holder (Continuous Type) CH-D" is designed as a single unit, allowing for significant labor savings in the application process compared to traditional individual piece card holders. It can be freely cut along the welded sections for use. 【Features】 - As a single unit, it enables significant labor savings in the application process - Can be freely cut along the welded sections - Holds 40 pieces of cards per sheet - Compatible card size: 19mm x 39mm *For more details, please refer to the PDF document or feel free to contact us.

The "Thermo Marker 80 TM080RY" is a marker that allows for simultaneous checking of connection points and temperature management, enabling efficient work. It begins to change color at temperatures above 65°C, and at temperatures above 80°C, the color change locks in and does not revert at normal environmental temperatures. Therefore, even during inspections when the power is off, you can identify areas that have exceeded 80°C. It can be used on surfaces such as screw heads and copper bars, and can also serve as a substitute for temperature indication seals. 【Features】 ■ Simultaneous checking of connection points and temperature management ■ Irreversible type ■ Usable on surfaces such as screw heads and copper bars ■ Can be used as a substitute for temperature indication seals *For more details, please refer to the PDF document or feel free to contact us.

**Features** <Irreversibility> 1. High precision while being low cost. 2. Reversible and combination types are also available. <Combination type of reversible + irreversible / Reversible type> 1. Environmentally friendly materials (paraffin wax, PET-based film) are used. 2. High precision (±2°C), fast response (fastest color development in 2 seconds), and high durability (outdoor use with over 6 years of weather resistance). *For more details, please refer to the PDF document or feel free to contact us.*

At Shinohara Electric, we handle "Fire and Hazardous Material Sign Boards." Starting with the "Hazardous Area Room Sign," we offer a wide range of products recommended by the Japan Fire Sign Industry Association, including "Fire Sign Boards." We have hard vinyl, printed types, and laminated types available. 【Product Lineup】 < Hazardous Area Room Signs > ■ Hazard G11: Pump Room ■ Hazard G12: Boiler Room ■ Hazard G13: Electrical Room ■ Hazard G14: Machinery Room, etc. *For more details, please refer to the PDF materials or feel free to contact us.

The "Repair Sheet" handled by Shinohara Electric is an adhesive sheet that matches the color of the panel's paint. By applying it over scratches or peeling on the painted surface, simple repairs can be made. It can also be used to protect cut edges. 【Features】 ■ Adhesive sheet that matches the color of the panel's paint ■ Allows for simple repairs by applying over scratches or peeling on the painted surface ■ Can also be used to protect cut edges *For more details, please refer to the PDF document or feel free to contact us.

The "Repair Sheet Round" handled by Shinohara Electric is a seal that can be used for simple repairs of unnecessary screw holes on the painted surfaces of existing panels due to design changes or processing errors. Since it is round, it allows for easy repair of screw holes. 【Features】 - It comes in three colors that match the panel's paint: 5Y7/1, 2.5Y9/1, and 2.5Y8/2. - Being round, it can easily repair screw holes ranging from M3 to M12. - The seal in 3.6Y6/0.5 color (silver gray) is less noticeable on steel plate surfaces. *For more details, please refer to the PDF document or feel free to contact us.

The "Repair Sheet Roll Type RS-W50L20" handled by Shinohara Electric is an adhesive sheet for indoor panels that matches the paint color of the panel. It allows for easy repairs by applying it over scratches or peeling on the painted surface. It can also be used to protect cut edges. 【Features】 ■ An adhesive sheet that matches the paint color of the panel (width 50mm, length 20m). ■ Easy repairs can be made by applying it over scratches or peeling on the painted surface. It can also be used to protect cut edges. *For more details, please refer to the PDF document or feel free to contact us.

It comes with an adhesive material (double-sided tape), so you can simply stick it directly onto the area you want to protect from scratches, eliminating the need to bend thin sheets and prepare protective fittings as in the past. 【Features】 ■ Since it comes with an adhesive (double-sided tape), you can stick it directly onto the area you want to protect from scratches, without the need to bend thin sheets and prepare protective fittings as before! ■ It can protect the board from scratches caused by fasteners and rods. ◇ 200 sheets per roll ■ It is rolled up, making it very convenient for storage. Additionally, the product can be easily peeled off from the separator (release material), which improves work efficiency. ◇ Thick type ■ It has a thickness of 1.5 times that of conventional products (60μm) and about 5 times the abrasion resistance! ■ With a large size (80mm x 80mm), it can protect a wider area! *For more details, please refer to the PDF document or feel free to contact us.

The foam section is flame-retardant, elastic, and highly durable. We offer a lineup that includes "D sponge" with a hardness of approximately 25°, "SD sponge" with a hardness of approximately 20°, and "SS sponge" with a hardness of approximately 10°. 【Features】 The foam section is flame-retardant, elastic, and highly durable. *For more details, please refer to the PDF document or feel free to contact us.

【Features】 1. Excellent elasticity, water resistance, and dust resistance. 2. It has a dual structure of sponge and hard rubber, allowing for easy straight application without the need for traditional guides or packing that prevent wavering. *For more details, please refer to the PDF document or feel free to contact us.

【Features】 Excellent heat resistance, cold resistance, oil resistance, weather resistance, and chemical resistance. *For more details, please refer to the PDF document or feel free to contact us.*

【Features】 1. Excellent weather resistance, oil resistance, chemical resistance, cold resistance, and thermal stability. 2. Flexural fatigue strength, aging resistance, and ozone resistance are several times greater than that of rubber. *For more details, please refer to the PDF document or feel free to contact us.

"Groove rubber" is a packing that can be used to protect the openings of various enclosures. We offer a lineup including "RP-MB," which can be commonly used for plate thicknesses of 1.6 to 3.2 mm due to its internal groove, "RP-MB-15," which protects the cross-section of plates with a thickness of 1.6 to 3.2 mm, and "RP-KE," which has a high holding power due to its internal core and can be commonly used for plate thicknesses of 0.8 to 2.3 mm. 【Features】 ■ RP-MB: Can be commonly used for plate thicknesses of 1.6 to 3.2 mm due to its internal groove. ■ RP-MB-15: Can protect the cross-section of plates with a thickness of 1.6 to 3.2 mm. ■ RP-KE: Has a high holding power due to its internal core and can be commonly used for plate thicknesses of 0.8 to 2.3 mm. *For more details, please refer to the PDF document or feel free to contact us.

The "Inset Packing" handled by Shinohara Electric is excellent in waterproofing and is particularly suitable for drainage packing. 【Features】 1. By using it at the opening of the distribution box, complicated metalwork for drainage sections becomes unnecessary. 2. It can be easily installed by simply pushing it into the edge of the metalwork, improving work efficiency. 3. There are two types available: one for vertical metal edges (without drainage structure) and one for horizontal metal edges (with drainage structure), allowing you to choose according to your application. *For more details, please refer to the PDF materials or feel free to contact us.*

The "Solar Power Generation Equipment Display Label" is a label that indicates the installation of solar power generation equipment at building entrances, serving to alert to the risk of electric shock during firefighting activities in the event of a fire. It is produced in accordance with the guidelines of the Tokyo Fire Department. 【Features】 ■ Produced in accordance with the guidelines of the Tokyo Fire Department ■ Indicates the installation of solar power generation equipment at building entrances ■ Aims to raise awareness of the risk of electric shock during firefighting activities in the event of a fire *For more details, please refer to the PDF document or feel free to contact us.

The "Ventilation Gallery (made of steel and stainless steel)" is a product used as a ventilation component for operation panels, control panels, distribution boards, cubicles, etc. Since it eliminates the need for processing ventilation holes in panels as in the past, it significantly reduces labor. Additionally, installation is extremely simple; the product can be fitted into the panel hole from the front and secured with a backing frame using screws from the back. With accessories such as a blow-in prevention cover, insect mesh, and dust filter, specifications can be selected according to the application. Other options include "Corrosion-resistant specification IP41" and "Filter front replacement type G2-20FM (for indoor use)" among the lineup. 【Features】 ■ No need for processing ventilation holes in panels ■ Extremely easy installation ■ Specifications can be selected according to application with accessories ■ Can also be used outdoors with the blow-in prevention cover (accessory) ■ Insect mesh compatible with IPX2 is also available *For more details, please refer to the PDF document or feel free to contact us.

The "Splash-proof Gallery IP45" is a product used for cubicles, distribution boards, etc., installed in harsh outdoor conditions exposed to wind and rain. 【Features】 1. There is no need to process large panels for ventilation holes as before. Please install this "Ventilation Gallery" as a component afterwards. 2. The ventilation gallery and the splash-proof cover are integrated, providing good waterproofing and a structure that withstands JIS C 0920 (splash-proof test). 3. There is also a stainless steel ventilation gallery available. *For more details, please refer to the PDF materials or feel free to contact us.*

The "Anti-Splash Type Gallery (Salt Damage Prevention Specification)" is a product designed for salt damage prevention, featuring excellent impact resistance and achieving more than twice the lifespan of conventional products. It has a high collection efficiency for marine salt particles, and even when the collected marine salt particles deliquesce, the increase in pressure loss is low, resulting in approximately half the low pressure loss compared to conventional products. Additionally, we offer a cover resin type that allows for the use of standard salt-resistant filters and dust filters interchangeably. 【Features】 ■ Salt damage prevention specification ■ Low pressure loss (about half of conventional products) ■ High collection efficiency for marine salt particles ■ Long lifespan (more than twice that of conventional products) ■ Excellent impact resistance *For more details, please refer to the PDF materials or feel free to contact us.

The "Slim Splash-Proof Gallery" achieves significant downsizing in depth dimensions while ensuring the same level of protection as conventional products, allowing for space-saving design. Thanks to the effect of the inner parts, the filter surface is less exposed to rain and wind, so even in rainy weather, the water film does not reduce the filter's ventilation capacity. Maintenance work on the filter can be performed from the front side. A fan can be installed on the back side (please use it for exhaust purposes when installing the fan). We also offer a salt damage-resistant version in 20 types "GTS-20W-ST" and 45 types "GTS-45W-ST." 【Features】 ■ Inner parts allow air to pass while stopping water ■ Space-saving and compact ■ Splash-proof: IP45 ■ Filter replacement possible from the front ■ Ventilation fan installation available (back side) *For more details, please refer to the PDF document or feel free to contact us.

The "Inwing Type Ventilation Gallery (Splash-Proof Type) IP45" is designed for outdoor use with a splash prevention cover, ensuring an opening area of 148 cm². Since there is no need for processing ventilation holes in the panel as in conventional designs, significant labor savings can be achieved, and adding additional ventilation holes is also easy. Moreover, by combining the rear-side gallery with the splash prevention cover, it offers excellent waterproofing and is constructed to withstand JIS C 0920 (splash-proof test). 【Features】 ■ Splash-proof type IP45 ■ Outdoor specification with splash prevention cover ■ Double-structured gallery ■ No need for processing ventilation holes ■ Easy to add ventilation holes ■ Excellent waterproofing and withstands JIS C 0920 (splash-proof test) *For more details, please refer to the PDF document or feel free to contact us.

The "Fan-equipped Gallery (Salt Damage Prevention Specification) IP45" is a product used for forced ventilation (exhaust) of various panels. It features a salt-resistant filter designed for salt damage prevention, and its structure is excellent in waterproofing due to the drainage filter. Additionally, we also offer stainless steel fan-equipped galleries that can be used outdoors. 【Features】 ■ Salt damage prevention specification with a salt-resistant filter ■ Excellent waterproof structure ■ Can be installed with only corner hole processing on the panel ■ The included fan comes with a finger guard and power cord ■ The drainage filter and dust filter can be regenerated through cleaning ■ Standard paint color: Munsell 5Y7/1 semi-gloss *For more details, please refer to the PDF materials or feel free to contact us.

The "Fan Unit" is a product used as a ceiling exhaust component for control panels. When exhausting from the top of the panel, the hinge structure allows for easy maintenance and replacement of the filter from the inside, eliminating the need for high-altitude work or ladders. Since the fan and terminal block are pre-assembled, installation is simple: just connect the power line to the terminal block after mounting it to the enclosure. 【Features】 ■ Easy filter maintenance with a hinge structure ■ Filter replacement can be done from inside the control panel, eliminating the need for high-altitude work ■ Fan and terminal block are pre-assembled ■ Maximum airflow (m3/min): 50/60Hz 2.0/2.3 *For more details, please refer to the PDF document or feel free to contact us.

The "Small Ventilation Gallery (for Indoor Use)" can be installed as a component for ventilating indoor distribution boards, control panels, instrument panels, etc., after the completion of the enclosure (it is not waterproof). There is no need to directly process ventilation holes in the panel as was done traditionally, and by installing it later, work efficiency can be improved. Additionally, it is also possible to install a 120 square motor fan. We also offer a small ventilation gallery with a dust filter that can be attached and removed from the front. 【Features】 ■ No need to directly process ventilation holes in the panel ■ Improved work efficiency by installing it later ■ Can also accommodate a 120 square motor fan (SG1-10-4) ■ Material: Steel plate…1.6mm with primer, Stainless steel…1.5mm *For more details, please refer to the PDF document or feel free to contact us.

The "Hooded Gallery IP34" is a ventilation component for control panels, operation panels, cubicles, etc. Due to its structure with a hood on the gallery, it is effective against wind and rain. Additionally, installation is simple; it can be mounted by inserting it into the panel hole from the front and securing it with screws from the back with a holding frame. With the included accessories such as an anti-blow cover, insect mesh, and dust filter, specifications can be selected according to the application (only FG-15 and FG-20). It can also be paired with a salt-resistant filter. 【Features】 ■ Its structure with a hood on the gallery makes it effective against wind and rain. ■ Installation is easy. It can be mounted by inserting it into the panel hole from the front and securing it with screws from the back with a holding frame (holding plate). ■ It can also be paired with a salt damage prevention filter. *For more details, please refer to the PDF materials or feel free to contact us.

The "Ventilation Fan Hood IP34" is a product used as a ventilation fan for control panels, control boards, cubicles, etc. It is easy to install; simply insert it into the panel hole from the front and secure the ventilation fan with screws from the back. The set includes the hood, fan, finger guard, and a power cord (1m), so you can use it right away. If you want to maintain a similar opening area for the hood in relation to the fan diameter, you can use a mounting plate to install a hood that is one size larger. 【Features】 - Easy installation. Just insert it into the panel hole from the front and secure the ventilation fan with screws from the back. - The set includes the hood, fan, finger guard, and a power cord (1m), so you can use it right away. - If you want to maintain a similar opening area for the hood in relation to the fan diameter, you can use a mounting plate to install a hood that is one size larger. *For more details, please refer to the PDF document or feel free to contact us.

The "Free Aluminum Gallery" is an aluminum ventilation gallery designed for ventilation within enclosures such as cubicles, distribution boards, and control panels. It can be manufactured to your specified dimensions, eliminating the need to process ventilation holes directly into the panels as was done traditionally. Please install this product as a component afterward. It offers high ventilation efficiency and is opaque. It is lightweight and does not pose a rust concern. 【Features】 ■ Customizable to your specified dimensions ■ No need to process ventilation holes in the panels ■ High ventilation efficiency and opaque ■ Lightweight with no rust concerns *For more details, please refer to the PDF materials or feel free to contact us.

The "Connected Plastic Gallery (for indoor use)" is a ventilation component for control panels, instrument panels, etc. Holes are drilled to the panel cut dimensions, and the plastic gallery can be easily fitted from the front and mounted with mounting brackets from the back. The "GP-9" can accommodate a 92mm square fan motor, while the "GP-12" can accommodate a 120mm square fan motor. Additionally, the installation of dust filters is also easy. Furthermore, by using the plastic gallery joints (PGJ-12, PGJW-12), it can be connected in pairs, threes, and so on (only for GP-12). 【Features】 ■ For indoor use ■ Easy to install ■ Easy installation of dust filters ■ Can be connected using plastic gallery joints (only for GP-12) *For more details, please refer to the PDF document or feel free to contact us.